Sample network setup Succession CSE | Nortel Networks 555-7101-217

May 2003

1001rp server description

Sample network setup: Succession CSE 1000

The following diagram shows a CallPilot server network setup with a Succession CSE 1000 system:

i2004 Internet phonesets

Web-enabled	Desktop
CallPilot	client
administrative	PC
PC

Telephony LAN/Customer LAN (10/100BaseT or 100BaseT)

	Internet	Succession
		CSE 1000 Media
	Telephony
		Gateway Expansion
	Gateway
		Modem
	Line Card

CallPilot

server

CE-MUX

DS-30x

Internet

Telephony

Gateway

Line Card

	Succession
Succession	CSE 1000
CSE 1000	Media	MGate	MPB16-4
Call Server	Gateway	card	board

Embedded LAN (10BaseT)

Router or Ethernet switch (optional)

Optivity

Telephony

Manager

PC

Laptop	Web-enabled
	CallPilot
	administrative
	PC

G101636

Part 2: 1001rp Server Hardware Installation

21

Image 21

Nortel Networks 555-7101-217 manual Sample network setup Succession CSE, Telephony LAN/Customer LAN 10/100BaseT or 100BaseT

Contents

CallPilot P0605618 CallPilot Page Publication history Publication history Contents Installing the server and connecting the peripheral DevicesIndex A p t e r 1001rp server description Server dimensions and weight Server featuresIntroduction 49.5 cm 19.5 Alarm board Front panel features front view without the front bezel Rear panel diagram Overhead view of empty server showing PCI and ISA connectors Slot assignments Slot definition and slot numbering1001rp slot assignments Reserved for COM1 COM2 I/O bracket Slot Single Board Computer SlotElan Network card Slot Clan Network card Slot 12b BRD20 IRQ mapping table IRQ Network connectivity Customer LAN optional Sample network setup Meridian Telephony LAN/Customer LAN 10/100BaseT or 100BaseT Sample network setup Succession CSE CallPilot Elan and Clan network setup Switch connectivity Network requirements Remote access connectivity Modem Kbps external modem NTRH9078 provides Supported peripheral devicesSince the modem is an external device, it requires its own Also supported, but has been replaced by the 56 Kbps Preparing for installation Installation checklist Installation overview May 2003Preparing for installation Conventions for warnings Follow this procedure to unpack the server and peripherals Unpacking the 1001rp serverTo unpack the equipment What’s next? About the front bezel doors Removing the front bezel and server cover To remove the front bezel To remove the server cover High current inside the chassis can cause severe injuryContinue with Inspecting the server interior on To replace the front bezel after installation is complete To inspect the server interior Inspecting the server interior Preparing for installationStandard Power supply installation Safety precautions Safety informationEquipment handling guidelines Section a Installing the power supply modules AC or DC Installing the second power supply module AC or DC About the power supply moduleAC versus DC systems Power supply modules Do one of the following To install the power supply module Section B Setting up DC power source for a 1001rp DC server DC wire gauge tables Metric wire conversion DC rack cabling Following diagram shows typical rack power cabling 48VDC power distribution rationale Multiple PDUs About the Power Distribution Unit DC power input PDU terminal blocks and wiring diagram To bring DC power and ground into the PDU Bringing power and ground into the PDU May Power supply installation Installing the server and connecting the peripheral devices To install the server Installing the server Required equipment Preparing the modem DIP Modem DIP switches To set the modem DIP switches OFF Loads Y or Y1 configuration from OFF The modem sends a CD signal when itAT command set recognition OFF Disables command recognition dumb Rear panel connections Connecting peripherals to the server To connect the modem to the server To connect the mouse, keyboard, and monitor to the server Continue with Connecting the server to the Elan on Connecting the server to the Elan Media Access Control addressTo connect the server to the Elan Feature key adapter dongle. See To connect the server to the Clan Connecting the server to the Clan optional What’s next? Installing the Nortel Networks software feature key adapter For installation, you require a Phillips No screwdriver To install the software feature key adapterContinue with Connecting the server to power on Requirements Before you begin Connecting the server to power CallPilot server To connect the 1001rp AC server to power Connect the DC power cable to the server, as shown below To connect the 1001rp DC server to power To start the server Binder Installing the server and connecting the peripheral devices Index Clan Elan May Index Index Page Product release Document release Standard Date May