| Table |
| FLOW RATE MODE | ||
| KEY | DISPLAY |
| ACTION TAKEN | |
|
|
| SHOWS |
| AND PROCEDURE |
|
|
|
|
|
|
|
|
| xx:xx:xx |
| Displays cumulative TIME since start |
|
| TIME |
|
| |
|
|
|
| Press the TIME key. The display flashes the time that the pump has | |
|
|
|
| ||
|
|
|
| been running (xx:xx:xx). | |
|
|
|
|
|
|
|
|
| xxx mL/min |
| Displays current FLOW RATE setting |
| FLOW |
|
| ||
| RATE |
| or |
|
|
|
|
| 1. | Press the FLOW RATE key. The display flashes the flow rate | |
|
|
| |||
|
|
| xxx L/min | ||
|
|
|
| setting you selected just before starting the pump. | |
|
|
|
|
| |
2.Use the UP and DOWN ARROW keys to enter the FLOW RATE setting you desire. As you use the UP and DOWN ARROW keys, the display changes accordingly. Refer to Figure
|
|
|
|
|
| xxx mL/min | Displays current TOTAL VOLUME |
|
|
|
| TOTAL | |||
|
|
|
| VOLUME |
| or |
|
|
|
|
|
|
| xxx Liters | Press the TOTAL VOLUME key. The display flashes the calculated |
|
|
|
|
|
|
| volume of fluid dispensed since the pump started running (xxx mL or |
|
|
|
|
|
|
| xxx Liters). |
|
|
|
|
|
|
|
|
|
|
|
|
|
| TUBE ID=xxx | Displays current TUBE ID |
|
| TUBE ID |
|
| |||
|
|
|
|
|
| ||
|
|
|
|
|
|
| Press the TUBE ID key. If the red LED next to the CALIBRATE key |
|
|
|
|
|
|
| |
|
|
|
|
|
|
| is not lit, the display flashes the current TUBE ID setting. If the red |
|
|
|
|
|
|
| LED next to the CALIBRATE key is lit, the display flashes the |
|
|
|
|
|
|
| message “CALIBRATED TUBE!”. |
|
|
|
|
|
|
|
|
|
|
|
|
|
| CALIBRATED! | Displays calibration state |
|
|
| CALIBRATE |
| |||
|
|
|
| or |
| ||
|
|
|
|
|
|
| |
|
|
|
|
|
| not calibrated | 1. Press the CALIBRATE key. If the red LED next to the |
|
|
|
|
|
|
| CALIBRATE key is not lit, the display shows “not calibrated”.. |
|
|
|
|
|
|
| If the red LED next to the CALIBRATE key is lit, the display |
|
|
|
|
|
|
| shows “CALIBRATED!”. |
|
|
|
|
|
|
| To calibrate a tube: |
2.Press the START/STOP key to stop the pump. The display returns to the STOPPED Display Mode. For detailed instruc- tions on “Calibrating a Tube”, refer to Section 5.5.
and | xxx mL/min | NOTE: if you press the UP and DOWN ARROW keys, the display |
| or | shows the current FLOW RATE setting. This setting |
| xxx L/min | changes accordingly as you use the UP and DOWN |
|
| ARROW keys but does not wrap around at maximum and |
|
| minimum values while the pump is running. |
|
|
|
Language |
| NOTE: if you press the Language button, the display changes to |
Button |
| the next language in the sequence: English, French, |
|
| Spanish, German, and Italian. |
