Manuals / Omega Vehicle Security / Household Appliance / Heat Pump

Omega Vehicle Security FPU5-MT-110 6.6.2Auxiliary In Remote Start/Stop, 500Ω LED, Aux Out V+

Models: FPU5-MT-110 FPU5-MT-220

1 83

Download 83 pages 6.26 Kb

Page 59

500Ω LED

6Operating the Pump Motor in the RUNNING Display Mode

500Ω LED

Aux Out V+

+

9Volts

–

Aux Out Gnd

Figure 6-10. Schematic of Auxiliary Out Circuit

1.Connect the circuit shown to the Auxiliary Out terminals with the motor stopped.

2.Press the START/STOP key. The motor starts, and the LED in the circuit goes off.

3.Press the START/STOP key. The motor stops, and the LED in the circuit lights up.

6.6.2Auxiliary In (Remote Start/Stop)

The Auxiliary In function allows you to remotely start and stop the pump motor. The Auxiliary In terminals are located near the bottom, on the back of the pump motor, next to the Auxiliary Out terminals.

1.Momentarily short the Auxiliary In V+ terminal to the Auxiliary In Ground terminal. The pump starts. The display enters the RUNNING Display Mode.

2.Momentarily short the Auxiliary In V+ terminal to the Auxiliary In Ground terminal. The pump stops. The display enters the STOPPED Display Mode.

NOTE

The momentary shorting action may be achieved with proper TTL or CMOS circuitry.

6-22

Image 59

Omega Vehicle Security FPU5-MT-110 manual 6.6.2Auxiliary In Remote Start/Stop, 500Ω LED, Aux Out V+, 9Volts, Aux Out Gnd

Contents

Shop online at User’s GuideFPU5-MT-110, FPU5-MT-220 OMEGAFLEX Peristaltic Pump MotorCanada Servicing North AmericaFor immediate technical or application assistance Servicing EuropeUnpacking Instructions TABLE OF Peristaltic Pump Motor Page Peristaltic Pump MotorTABLE OF CONTENTSPeristaltic Pump Motor I Index IIndex Index 1.1 Description 1.2Features1 Introduction 1Introduction Description Parts of the Pump Motor2.1 Front View Table 2-1.Front ViewFunction 2.2 Left Side ViewTable 2-2.Left Side View DescriptionFunction 2.3 Right Side ViewTable 2-3.Right Side View DescriptionFunction 2.4 Membrane Keypad and DisplayTable 2-4.Membrane Keypad Detail DescriptionDescription Table 2-4.Membrane Keypad Details cont’dTOTAL VOLUME key Initiates the TOTAL VOLUME Mode ofRPM settings from 10 RPM to 600 RPM 2.5 Rear ViewTable 2-5.UP and DOWN ARROW Keys Scrolling Limits Table 2-6.Rear ViewLANGUAGE Button Rear View cont’dDescription Function2Parts of the Pump Motor 3.1.1Introduction Table 3-1.Pump Motor Mounting ConfigurationsGetting Started 3.1Attaching the PumpFigure 3-3.Pump in Closed Position Refer to Figures 3-1throughFigure 3-1.Pump in Closed Position Figure 3-2.Aligning the Rotor ShaftGetting Started 3.1.3Stacking Two Pumps on One Side of the MotorFollow this procedure refer to Figures 3-8through 3.2 Selecting Tubing3.3 Tubing Life 3.4 Loading the TubingFigure 3-11.Closing the Stator See Section 5.2 to set the pumping direction3Getting Started 4.3 The STOPPED Display Mode Turning on the Power4.2 Using the ON/OFF Switch 4.1 Introduction to the Two Display ModesFigure 4-2.RUNNING Display Mode 4.4 The RUNNING Display ModeFigure 4-1.STOPPED vs. RUNNING Display Modes Italian ACTION Language Changes Operating the Pump Motor in theSTOPPED Display Mode Display shows English French Spanish GermanGerman EnglishFrench Spanish1.Refer to Figure 5.2 Defining the Direction of PumpingLeft Pump 5.3Selecting the Tubing Inner DiameterLeft Pump Right PumpEnglish Table 5-2.Tube Inner DiametersTube Inner Diameters Metric5.5 Calibrating the Tubing 5.4 Priming the TubingPage TIPS FOR OPTIMUM CALIBRATION ACCURACY Display shows 5.6 Measuring the Temperature of a Fluid5.7 Preparing for Pumping in a Specific Mode when the button isDisplay shows Operating the Pump Motor in the RUNNING Display Mode6.1 The RPM Mode 6.1.1 Pumping in the RPM ModePage ACTION TAKEN AND PROCEDURERPM MODE DISPLAYDISPLAY Table 6-1cont’dAND PROCEDURE RPM MODE4.Press the FLOW RATE key 6.2 The FLOW RATE Mode6.2.1 Pumping in the FLOW RATE Mode Page Figure 6-4.FLOW RATE Ranges cont’d press again pumps stops Display xxx mL/min ACTION Pumps startsACTION TAKEN FLOW RATE MODEAND PROCEDURE DISPLAYDISPLAY Table 6-2cont’dFLOW RATE MODE AND PROCEDURE6.3.1 Pumping in the TIME Mode 6.3 The TIME ModeDisplay shows xx xx xx ACTION Displays current TIME settingFigure 6-6.TIME Range Page ACTION TAKEN TIME MODEAND PROCEDURE DISPLAYDISPLAY Table 6-3cont’dTIME MODE AND PROCEDUREDispensed 6.4 The TOTAL VOLUME ModeTotal Volume is Dispensed Stop before6.4.1 Pumping in the TOTAL VOLUME Mode 6-18 ACTION TAKEN Table 6-4TOTAL VOLUME MODEAND PROCEDURE DISPLAYDISPLAY TOTAL VOLUME MODETable 6-4cont’d AND PROCEDURE6.6.1Auxiliary Out Remote Monitor 6.6Other Pumping OptionsClamp Screw 9Volts 6.6.2Auxiliary In Remote Start/Stop500Ω LED Aux Out V+Problem Troubleshooting Guide7.1 Display Error Messages Error Message1.Press the START/STOP key to start the motor Error MessageSolution Illegal Op Code continued B3.Press the START/STOP key to start the pump Error MessageProblem Locked Rotor?Must STOP first Error MessageProblem 4.Press the START/STOP key to start the pump Error MessageProblem 1.Press the TOTAL VOLUME keyShort Circuit? Error MessageProblem SolutionWatchdog Failure A Error MessageSolution Solution 7.2 Other Pumping ProblemsProblem No flow out of the tube outlet ProblemSolution Motor will not turn ProblemSolution 7-11 Troubleshooting Guide8.1 Theory of Operation 8.3 Design Solution8.4 Maintenance Technical Details8Technical Details Table 9-1.Calibration Accuracy 9 SpecificationsBetween Pumps Table 9-2.Average Flow RatesTubing Size Due toTable 9-4.Average Tubing Life Minimum Motor Speed RPM Tubing Size - IDTable 9-6.Average Flow Rates For Viscous Liquids mL Per Revolution9Specifications Part Number Spare Parts and AccessoriesTable 10-2.Accessories Table 10-1.Spare Parts10-2 Table 10-2.Accessories cont’dOD x ID 10-3 Spare Parts and AccessoriesFigure 10-1.Peristatic Pump 10-4 10Spare Parts and AccessoriesRETURN REQUESTS/INQUIRIES WARRANTY/DISCLAIMER