Manuals / Omega Vehicle Security / Household Appliance / Heat Pump

Omega Vehicle Security FPU5-MT-220 manual Operating the Pump Motor in the, STOPPED Display Mode

Models: FPU5-MT-110 FPU5-MT-220

1 83

Page 28

	5	Operating the Pump Motor in the
	5	STOPPED Display Mode
		STOPPED Display Mode

5.1 Displaying Pump Messages in Five Different Languages

Language

Display shows

English

French

Spanish

German

Italian

ACTION

Language

Changes

The LANGUAGE button, located toward the bottom on the back of the pump motor, changes the language of the pump messages.

1.To display pump messages in another language, press the LANGUAGE button. The language of the pump messages changes according this sequence: English, French, Spanish, German, then Italian. This manual only shows pump messages in English in the display. Table 5-1 shows the English, French, Spanish, German, and Italian messages.

2.If the new language is the language you want, resume pumping. All the pump messages are now in the new language.

3.If the new language is not the one you want, press the LANGUAGE button repeatedly, so that the pump motor can cycle through the sequence to reach the proper LANGUAGE setting.

5-1

Page 28

Image 28

Omega Vehicle Security FPU5-MT-220 Operating the Pump Motor in the, STOPPED Display Mode, Italian ACTION Language Changes

Contents

User’s Guide FPU5-MT-110, FPU5-MT-220OMEGAFLEX Peristaltic Pump Motor Shop online atServicing North America For immediate technical or application assistanceServicing Europe CanadaUnpacking Instructions TABLE OF Peristaltic Pump Motor Peristaltic Pump Motor PagePeristaltic Pump Motor CONTENTSTABLE OF I Index IIndex Index 1 Introduction 1.2Features1.1 Description 1Introduction Parts of the Pump Motor 2.1 Front ViewTable 2-1.Front View Description2.2 Left Side View Table 2-2.Left Side ViewDescription Function2.3 Right Side View Table 2-3.Right Side ViewDescription Function2.4 Membrane Keypad and Display Table 2-4.Membrane Keypad DetailDescription FunctionTable 2-4.Membrane Keypad Details cont’d TOTAL VOLUME keyInitiates the TOTAL VOLUME Mode of Description2.5 Rear View Table 2-5.UP and DOWN ARROW Keys Scrolling LimitsTable 2-6.Rear View RPM settings from 10 RPM to 600 RPMRear View cont’d DescriptionFunction LANGUAGE Button2Parts of the Pump Motor Table 3-1.Pump Motor Mounting Configurations Getting Started3.1Attaching the Pump 3.1.1IntroductionRefer to Figures 3-1through Figure 3-1.Pump in Closed PositionFigure 3-2.Aligning the Rotor Shaft Figure 3-3.Pump in Closed Position3.1.3Stacking Two Pumps on One Side of the Motor Getting Started3.2 Selecting Tubing 3.3 Tubing Life3.4 Loading the Tubing Follow this procedure refer to Figures 3-8throughSee Section 5.2 to set the pumping direction Figure 3-11.Closing the Stator3Getting Started Turning on the Power 4.2 Using the ON/OFF Switch4.1 Introduction to the Two Display Modes 4.3 The STOPPED Display ModeFigure 4-1.STOPPED vs. RUNNING Display Modes 4.4 The RUNNING Display ModeFigure 4-2.RUNNING Display Mode Operating the Pump Motor in the STOPPED Display ModeDisplay shows English French Spanish German Italian ACTION Language ChangesEnglish FrenchSpanish German5.2 Defining the Direction of Pumping 1.Refer to Figure5.3Selecting the Tubing Inner Diameter Left PumpRight Pump Left PumpTable 5-2.Tube Inner Diameters Tube Inner DiametersMetric English5.4 Priming the Tubing 5.5 Calibrating the TubingPage TIPS FOR OPTIMUM CALIBRATION ACCURACY 5.6 Measuring the Temperature of a Fluid 5.7 Preparing for Pumping in a Specific Modewhen the button is Display showsDisplay shows RUNNING Display Mode 6.1 The RPM Mode6.1.1 Pumping in the RPM Mode Operating the Pump Motor in thePage AND PROCEDURE RPM MODEDISPLAY ACTION TAKENTable 6-1cont’d AND PROCEDURERPM MODE DISPLAY6.2.1 Pumping in the FLOW RATE Mode 6.2 The FLOW RATE Mode4.Press the FLOW RATE key Page Figure 6-4.FLOW RATE Ranges cont’d Display xxx mL/min ACTION Pumps starts press again pumps stopsFLOW RATE MODE AND PROCEDUREDISPLAY ACTION TAKENTable 6-2cont’d FLOW RATE MODEAND PROCEDURE DISPLAY6.3 The TIME Mode 6.3.1 Pumping in the TIME ModeFigure 6-6.TIME Range TIME settingDisplay shows xx xx xx ACTION Displays current Page TIME MODE AND PROCEDUREDISPLAY ACTION TAKENTable 6-3cont’d TIME MODEAND PROCEDURE DISPLAY6.4 The TOTAL VOLUME Mode Total Volume is DispensedStop before Dispensed6.4.1 Pumping in the TOTAL VOLUME Mode 6-18 Table 6-4TOTAL VOLUME MODE AND PROCEDUREDISPLAY ACTION TAKENTOTAL VOLUME MODE Table 6-4cont’dAND PROCEDURE DISPLAYClamp Screw 6.6Other Pumping Options6.6.1Auxiliary Out Remote Monitor 6.6.2Auxiliary In Remote Start/Stop 500Ω LEDAux Out V+ 9VoltsTroubleshooting Guide 7.1 Display Error MessagesError Message ProblemError Message SolutionIllegal Op Code continued B 1.Press the START/STOP key to start the motorError Message ProblemLocked Rotor? 3.Press the START/STOP key to start the pumpProblem Error MessageMust STOP first Error Message Problem1.Press the TOTAL VOLUME key 4.Press the START/STOP key to start the pumpError Message ProblemSolution Short Circuit?Solution Error MessageWatchdog Failure A Problem 7.2 Other Pumping ProblemsSolution Solution ProblemNo flow out of the tube outlet Solution ProblemMotor will not turn Troubleshooting Guide 7-118.3 Design Solution 8.4 MaintenanceTechnical Details 8.1 Theory of Operation8Technical Details 9 Specifications Table 9-1.Calibration AccuracyTable 9-2.Average Flow Rates Tubing SizeDue to Between PumpsTable 9-4.Average Tubing Life Tubing Size - ID Minimum Motor Speed RPMmL Per Revolution Table 9-6.Average Flow Rates For Viscous Liquids9Specifications Spare Parts and Accessories Table 10-2.AccessoriesTable 10-1.Spare Parts Part NumberOD x ID Table 10-2.Accessories cont’d10-2 Figure 10-1.Peristatic Pump Spare Parts and Accessories10-3 10Spare Parts and Accessories 10-4WARRANTY/DISCLAIMER RETURN REQUESTS/INQUIRIES