Specifications | Onkyo USR-5RF specs

Specifications

Hardware	High-resolution (320 x 240) liquid crystal display (LCD) with contrast
	control
	Large touchscreen
	Seven programmable direct-access buttons
	Backlighting for LCD and direct-access buttons
	Infrared sending and learning eyes
	3-wire (RS232) serial port connector
Software	Dynamic, animated interface
	Editable macros (up to 255 commands per macro)
	Total number of devices and macros limited only by memory
	Database with RC codes to operate different brands
Infrared (IR)	Operating distance of 10 meters (33 feet)
	Learning frequency upto 56 KHz
	Learning distance 5 cm (2 inch) up to 30 cm (1 foot)
Radio	Operating distance of approximately 20 meters depending on the surrounding
frequency (RF)	conditions
	Band:418 MHz
	Bandwidth: +/–100 kHz
	16 Extender ID’s and 4 Channels
Memory	2 MB non-volatile flash memory (retains commands when batteries are not
	present)
	512 K SRAM
Batteries	4 AA 1.5V batteries, or one 4,8V rechargeable battery pack
Battery life	Approximately 6 months with typical use
Power management	Power on by tapping the touchscreen, power off automatically management
Dimensions	153.6 x 94.1 x 43.7 mm (6.0 x 3.7 x 1.7 inch)
Operating temperature	0 ˚C to 50 ˚C (32 ˚F to 122 ˚F)
Accessories	RS232 cable for PC connection
	4 AA 1.5 V batteries
Accessories	Remote controller recharge package BCC-5
(Not included)	RF Receiver RFR-5

43

Image 43

Onkyo USR-5RF instruction manual Specifications

Contents

USR-5RF Care Precautions Table of contents Operate your components Quick StartInsert batteries Touch the screen to start Quick reference Quick reference Modes Quick reference Direct-access buttons Intelligent Remote ControllerIntroduction Touchscreen buttons Left and Right buttonsWhich Buttons Can Be Programmed? AA batteries Charging the Remote Controller Optional recharging dock Getting Started Activate the remote controllerDefine the Brand of Your Device Select Yes to define the brand of the device to operate Defining brands by selectingTap Next Select your brand from the list Navigate through the list of brands Select a code set from the list Tap Search Defining brands by searching Via the Home menu Select a DeviceVia the Device menu Scrolling Using touchscreen buttonsSending commands Operate a Device IR commands Device pages Use the Left and Right button to adjust the setting Adjust the SettingsTouch and hold the remote controller icon for a few seconds Tap the button of the setting you want to adjust Third setup panel Second setup panel Introduction Getting the Maximum out of itWorking with Modes To hide the Mode menu Tap the mode you want to useTap Programming control panel buttons Programming Buttons Programming device items Programming direct-access and Left/Right ButtonsMake sure the device tab is active Labeling a button Labeling Buttons and Menu ItemsEdit the label Complete instruction 4 to 6 Labeling a button on Labeling a menu item Adding devices Adding and Moving DevicesMoving menu items Delete Delete and restoreDeleting a button or button function Tap the item you want to restore Restore Recording macros Recording Macros and Setting Timers Editing macros Setting timers Tap Create Timer Group or Create Macro Group Editing timersOrganizing macros and timers into groups Edit the timer Press the Left button to close the timer Using the remote controller with Radio Frequency Switch to RF IR mode by using Mode button Changing the remote controller’s RF IR SettingsTap RF Changing the Extender ID Try the devices which you just changed the RF IR settings Press the + and action buttons to change the Channel Switch back to RF IR modeSelect a device that is set with RF signals Choosing Another Channel With ChadEdit you can ChadEdit System requirements General Problems Programming Problems Troubleshooting Recharging Problems How do I revert to the original configuration? Can I program a button to execute more than one command?How do I program source switching? How do I reset the Remote controller? Overview of Symbols Specifications Onkyo U.S.A. Corporation