Messages

On the unit’s display

The following messages or service numbers appear on the unit’s display when something unusual is detected during startup and use.

 

 

 

 

 

 

 

 

 

 

 

Page

 

 

 

 

 

 

 

 

 

 

 

DVD

• The remote control and main unit are using different codes. Change

 

 

40

 

(“

” stands for a number.)

the code on the remote control.

 

 

 

 

 

 

 

 

 

 

 

Press and hold [OK] and the indicated number button at the same

 

 

 

 

 

 

 

 

 

 

 

time for more than 5 seconds.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

HARD ERR

• If there is no change after turning the unit on and off, consult the dealer where the unit was

 

 

 

 

 

 

 

 

purchased.

 

 

 

 

 

 

 

 

 

 

 

 

NoERAS

• Deleting an item may be unavailable due to a disc problem. Use a new disc.

 

 

 

 

 

 

 

 

 

 

 

NoREAD

• The disc is dirty or badly scratched. The unit cannot record, play, or edit.

5

 

 

 

 

 

 

 

 

• The message may appear when the DVD lens cleaner has finished cleaning.

5

 

 

 

 

 

 

 

 

Press [; OPEN/CLOSE] on the main unit to eject the disc.

 

 

 

 

 

 

 

 

 

 

 

 

NoWRIT

• Recording may be unavailable due to a disc problem. Use a new disc.

 

 

 

 

 

 

 

 

• The unit’s “TV System” setting differs from the TV system used by the disc. Change the “TV

39

 

 

 

 

 

 

 

 

System” in the Setup menu.

 

 

 

 

 

 

 

 

 

 

 

 

PLEASE WAIT

• Displayed when the unit is started. This is not a malfunction.

 

 

 

 

 

 

 

 

• The unit is carrying out its recovery process. You cannot operate the unit while “PLEASE

 

 

 

 

 

 

 

 

WAIT” is displayed.

 

 

 

 

 

 

 

 

 

 

 

 

PROG FULL

• There are already 16 timer programmes. Delete unnecessary timer programmes.

19

 

 

 

 

 

 

 

 

 

 

 

UNFORMAT

• You inserted an unformatted DVD-RAM, DVD-RW, +RW, an unused +R, +R DL or DVD-RW

35

 

 

 

 

 

 

 

 

(DVD-Video format) that has been recorded on other equipment.

 

 

 

 

 

 

 

 

 

Format the disc to use it.

 

 

 

 

 

 

 

 

 

However all the recorded contents on the disc are deleted.

 

 

 

 

 

 

 

 

 

 

 

 

UNSUPPORT

• You have inserted a disc the unit cannot play or record on.

6, 7

 

 

 

 

 

 

 

 

 

 

 

 

U59

 

 

 

 

 

• The unit is hot.

 

 

 

 

 

 

 

 

The unit switches to standby for safety reasons. Wait for about 30 minutes until the message

 

 

 

 

 

 

 

 

 

disappears.

 

 

 

 

 

 

 

 

 

Select a position with good ventilation when installing the unit. Do not block the cooling fan

 

 

 

 

 

 

 

 

 

on the rear of the unit.

 

 

 

 

 

 

 

 

 

 

 

 

 

U61

 

 

 

 

 

• The unit detected an error while recording or playing with no disc in the disc tray. The unit is

 

 

 

 

 

 

 

 

carrying out its recovery process. This process restores the unit to normal operation. The

 

 

 

 

 

 

 

 

 

unit is not broken. Wait until the message disappears.

 

 

 

 

 

 

 

 

 

 

 

 

 

U80

 

 

 

 

 

• The unit fails to operate properly. Press [8] on the main unit to switch the unit to standby

U81

 

 

 

 

 

mode. Now press [8] on the main unit again to turn the unit on.

 

U99

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

U88

 

 

 

 

 

• The unit detected an error while recording or playing with a disc in the disc tray. The unit is

47

 

 

 

 

 

 

 

 

carrying out its recovery process. This process restores the unit to normal operation. The

 

 

 

 

 

 

 

 

 

unit is not broken. Wait until the message disappears.

 

 

 

 

 

 

 

 

 

 

 

 

 

H

 

 

 

or F

 

 

 

• There is something unusual. (The service number displayed after H and F depends on the

 

 

 

 

 

 

 

 

 

 

 

 

 

unit’s condition.)

 

 

 

 

 

 

 

 

 

• Check the unit using the troubleshooting guide. If the service number does not disappear, do

46-49

 

 

 

 

 

 

 

 

the following.

 

 

 

 

 

 

 

 

 

1. Disconnect the plug from the household mains socket, wait a few seconds, then reconnect

 

 

 

 

 

 

 

 

 

it.

 

 

 

 

 

 

 

 

 

2. Press [8] to turn the power on. (The unit may be fixed.)

 

 

 

 

 

 

 

 

 

If the service number does not disappear despite after doing the above, request service from

 

 

 

 

 

 

 

 

 

the dealer. Inform the dealer of the service number when requesting service.

 

 

 

 

 

 

 

 

 

 

 

 

X HOLD

• The Child Lock function is activated.

41

 

 

 

 

 

 

 

 

Press and hold [OK] and [RETURN] simultaneously until “X HOLD” disappears.

 

 

 

 

 

 

 

 

 

 

 

 

 

The messages are alternately displayed.

RQT9053

44

Page 44
Image 44
Panasonic DMR-ES18 operating instructions Messages On the unit’s display