Settings

[PROJECTOR SETUP] menu

[COOLING CONDITION]

Change the fan control depending on the direction of projection.

Set [COOLING CONDITION] correctly in accordance with the direction of projection referencing the following figure. It may shorten the life of the lamp if used in incorrect setting.

1) Press ▲▼ to select [COOLING

CONDITION].

2) Press the <ENTER> button.

zzThe [COOLING CONDITION] screen is displayed.

3) Press ▲▼ to select a cooling condition.

[VERTICAL UP

SETTING]

[FLOOR

[CEILING

SETTING]

SETTING]

[VERTICAL DOWN SETTING]：Projection direction

4)Press the <ENTER> button.

5)When the confirmation is displayed, select [OK] or [CANCEL], and press the <ENTER> button.

[HIGH ALTITUDE MODE]

Set to [ON] to use the projector at 1 400 m (4 593 ft) to 2 700 m (8 858 ft) elevations.

1)Press ▲▼ to select [HIGH ALTITUDE

MODE].

2)Press ◀▶ to switch [HIGH ALTITUDE

MODE].

[OFF]

 

 

[ON]

 

 

[OFF]

When using at a place lower than

1 400 m (4 593 ft) above sea level

 

 

When using at a high altitude

[ON]

(1 400 m (4 593 ft) or higher and

lower than 2 700 m (8 858 ft) above

 

 

sea level)

3)When the confirmation is displayed, select [OK] or [CANCEL], and press the <ENTER> button.

Note

zzThe speed of the fan increases and the operation sound becomes louder when set to [ON].

zzThe optional smoke cut filter cannot be used when in high elevation mode.

[LAMP SELECT]

Select luminous lamps from the four equipped in the projector body to turn on for a certain use condition or purpose.

1) Press ▲▼ to select [LAMP SELECT].

2) Press ◀▶ to switch [LAMP SELECT]. zzThe setting will change as follows each time

you press the button.

[L1][L2]

[QUAD] (4 lit)

 

 

[L3]

 

 

 

[TRIPLE] (3 lit)

 

 

[L4]

 

 

 

[DUAL] (2 lit)

 

 

[L1/L4]

 

 

 

[SINGLE] (1 lit)

 

 

[L2/L3]

 

 

 

[L2/L3/L4]

 

 

[L1/L2/L3]

 

 

 

[L1/L3/L4]

 

 

[L1/L2/L4]

 

 

 

[L1]

Lamp 1 will light.

 

[L2]

Lamp 2 will light.

 

[L3]

Lamp 3 will light.

 

[L4]

Lamp 4 will light.

 

[L1/L4]

Lamp 1 and Lamp 4 will light.

[L2/L3]

Lamp 2 and Lamp 3 will light.

[L1/L2/L3]

Lamp 1, Lamp 2 and Lamp 3 will light.

[L1/L2/L4]

Lamp 1, Lamp 2 and Lamp 4 will light.

[L1/L3/L4]

Lamp 1, Lamp 3 and Lamp 4 will light.

[L2/L3/L4]

Lamp 2, Lamp 3 and Lamp 4 will light.

[SINGLE]

One lamp will light. (A short usage

(1 lit)

time lamp will automatically light.)

[DUAL]

Two lamps will light. (A short usage

(2 lit)

time lamp will automatically light.)

[TRIPLE]

Three lamps will light. (A short usage

(3 lit)

time lamp will automatically light.)

[QUAD]

Four lamps will light.

 

(4 lit)

 

 

 

 

 

3) Press the <ENTER> button.

100 - ENGLISH