Indicator | Lighting in red | Flashing in red | Flashing in red | ||
status | (2 times) | (3 times) | |||
|
| ||||
|
| Internal |
|
| |
Status | temperature | Internal temperature is high | The cooling fan has | ||
is high. | (standby mode) | stopped. | |||
|
| ||||
|
| (WARNING) |
|
| |
| zzDid you turn on the | zzIs the air intake/exhaust port blocked? |
| ||
Cause | power when the | zzIs the room temperature high? |
| ||
room temperature | zzIs the filter indicator <FILTER> not lit? | ― | |||
| was about 0°C |
|
|
| |
| (32°F)? |
|
|
| |
| zzWait at least five | zzRemove any objects that are blocking the air | zzTurn the <MAIN | ||
| minutes in the | intake/exhaust port. | POWER> switch to | ||
| current status. | zzMove the projector to a location with an | <OFF> ( page 51), | ||
Solution | zzInstall the unit | ambient temperature of 0°C (32°F) to 45°C | and consult your | ||
in a location | (113°F)*1 and a humidity of 20% to 80% (no | dealer. | |||
| with an ambient | condensation). |
| ||
| temperature of | zzClean the air filter unit or replace it. ( page 144) |
| ||
| 0°C (32°F) to 45°C |
|
|
| |
| (113°F)*1. |
|
|
| |
*1: When using the projector at high elevations (1 400 m (4 593 ft) – 2 700 m (8 858 ft) above sea level), the operating environment temperature will be 5°C (41°F) lower than the maximum limit.
When using a smoke cut filter, the temperature will be 0°C (32°F) to 35°C (95°F). However, it cannot be used at high elevations.
Note
zzIf the temperature indicator <TEMP> is still lit or flashing after taking the preceding measures, ask your dealer to repair the unit.
■■Filter indicator <FILTER>Indicator |
| Lighting in red |
| Flashing in red |
|
|
status |
|
|
| |||
|
|
|
|
|
| |
Status | The filter is clogged. |
|
| The air filter unit is not |
|
|
The temperature inside or outside the projector is abnormally high. | attached. |
|
| |||
|
| |||||
Cause | zzIs the air filter unit | zzIs the air intake/ | zzIs [HIGH ALTITUDE | zzIs the air filter unit |
|
|
dirty? | exhaust port | MODE] set | attached? |
| ||
|
| blocked? | correctly? |
|
|
|
| zzClean the air filter | zzRemove any objects | zzWhen using the | zzAttach the air filter |
|
|
| unit or replace it. | that are blocking the | projector at high | unit. |
| |
| ( page 144) | air intake/exhaust | elevations 1 400 m |
|
|
|
|
| port. | (4 593 ft) – 2 700 m |
|
|
|
|
|
| (8 858 ft) sea |
|
| Maintenance |
Solution |
|
| level, set [HIGH |
|
| |
|
| elevations 2 700 m |
|
| ||
|
| ALTITUDE MODE] |
|
|
| |
|
|
| ( page 100) to [ON]. |
|
|
|
|
|
| zzDo not use the |
|
|
|
|
|
| projector at high |
|
|
|
|
|
| (8 858 ft) or higher |
|
|
|
|
|
| above sea level. |
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
Note
zzIf the filter indicator <FILTER> is still lit or flashing after taking the preceding measures, ask your dealer to repair the unit.
zzIf the filter is clogged, only one lamp may light even when [LAMP SELECT] is set to [QUAD], [TRIPLE], or [DUAL]. Cleaning the air filter unit or replacing it with a new one will turn off the indicator.
ENGLISH - 143