Diagnostics Options, SN Selftest | Paradyne 8310 MVL, 8510 DSL

Diagnostics and Troubleshooting

"Procedure

To view selftest, card alarm, packet test, and SN self-test information:

1.Follow these menu sequences: Diagnostics → Selftest (D-A) Diagnostics → Alarms (D-B) Diagnostics → Packet Echo (D-C) Diagnostics → SN Selftest (D-D)

2.The Diagnostics menu appears. Select the submenu option as shown in Table 7-1 and press Return.

Table 7-1. Diagnostics Options

Selftest	D-A

Displays the results of the last disruptive selftest of the DSL card. This selftest is only performed on power up of the system or a reset of the card. Each subsystem (processors, memory, and interfaces) reports pass or fail. If all subsystems pass, the card has passed selftest. If a subsystem fails, reset or replace the card.

You can determine when the selftest occurred by reading the elapsed time since the last reset on the card.

Alarms (Card Alarms)	D-B

Displays all active card alarm conditions. Major alarms include Selftest failure, Processor failure (sanity timer), and DSL or Ethernet port failures. Minor alarms include Config Error (configuration has been corrupted) and threshold exceed for DSL margin or Link Down events.

DSL Packet Echo Test	D-C

Gives the user the ability to conduct a nondisruptive packet test between the DSL card and Hotwire SN endpoint. Test packets are sent to the SN at 10 percent of the line rate and echoed back to this card, where they are counted and checked for errors. The running time of the test can be specified and the test will continue until the specified time has elapsed or the test is stopped.

Results include packets sent, valid packets received, errored packets received, errored seconds, and elapsed time of the test.

NOTE: You can specify the DSL port number but only one port can be entered at a time.

SN Selftest	D-D

Gives the user the ability to perform a power-on SN selftest. A port number can be selected to perform the test.

NOTE: Entering yes in the Reset SN field will temporarily disrupt the data path on the specified DSL port while the SN resets.

7-2

May 1998

8000-A2-GB26-00

Image 76

Paradyne 8310 MVL, 8510 DSL manual Diagnostics Options, Alarms Card Alarms, DSL Packet Echo Test, SN Selftest

Contents

HOTWIRE Dslam for 8310 MVL and 8510 DSL Cards Copyright 1998 Paradyne Corporation All rights reserved Contents Initial Setup Instructions Traps Contents About This Guide Document Purpose and Intended Audience Document Summary Section Description Product-Related Documents Document Number Document Title Viii Hotwire Dslam System Description What is the Hotwire DSLAM? Central Office CO Optional Hotwire Dslam Components Hotwire Dslam chassis There are two types of chassis 98-15973 Features One Management Communications Controller MCC card Configuring the DSL Cards Levels of AccessSoftware Functionality Troubleshooting and Diagnostics Monitoring the DSL Cards Hotwire Dslam System Description Hotwire Menus and Screens Overview Components of a Hotwire Menu Menu and Screen Formats Components of a Hotwire Screen Commonly Used Navigation Keys Keys Definition Hotwire Chassis Main Menu Hotwire Menu HierarchyHotwire Chassis Hotwire ± MCC Menu Hotwire ± DSL MenuHotwire DSL Diagnostics Configuration PortsCard Status Interfaces Download Code Logging In to the System Reviewing the Levels of Access User Login Screen Card Selection Screen Position Display Description Manually Logging Off Exiting From the SystemAutomatically Logging Off Initial Setup Instructions Accessing the System for the First Time Initial Setup Instructions Additional Setup Instructions Chassis Information Screen Whats Next?Field Input Description Configuring the Hotwire Dslam Configuring the MCC Card and DSL Cards For each Access Node, perform task See For the Management Domain, perform task See Setting the IP Address and Subnet Mask Clear Nvram Setting Time and Date Creating the Default Route Configuration → Snmp → Communities/Traps A-F-B Configuring VLANs on a DSL or MVL Card Configuring the Active Vlan on each DSL or MVL Port Configuring the Next Hop Router for each Vlan Configuring Static Users Configuring the Hotwire Dslam MVL and 8510 DSL Card Configuration DSL Configuration Card Status Screens Card Status Options 1 Card Info Card InformationTime/Date Nvram Clear Card Status Options 2 Card Status Options 3 Apply Download Ports Options 1 DSL Configuration Ports ScreensEthernet Port Ports Options 2 DSL Ports DSL Parameters 8510 Card Ports Options 3 DSL Configuration Interfaces ScreensDSL Ports DSL Parameters 8310 Card DSL Configuration Users Screens Interfaces OptionsGeneral General Interfaces Control Control Interfaces DSL Configuration Bridge Screens Bridge Options 1 GeneralCard Vlan Card Port Vlan Port Bridge Options 2 Client Vlan ClientARP Parameters and Add ARP Entry E a and B Parameters a Service Node Options DSL Configuration Service Node ScreensSN Configuration Monitoring the Hotwire Dslam DSL Monitoring Card Status Screens Card Status Options Login HistoryCard Info General Card Information Physical Layer Options 1 DSL Monitoring Physical Layer ScreensActive List Active Ports List Physical Layer Options 2 Ethernet Stats Ethernet Statistics EtherHDLC Stats EtherHDLC Statistics Physical Layer Options 3Initialized EtherHDLC Ports ± s1c, s1d, s1e, or s1f DSL Link Perf DSL Link Performance Summary Physical Layer Options 4DSL Perf Stats DSL Performance Stats Physical Layer Options 5 DSL Error StatsDSL Xmit Status DSL Transmit Stats DSL Monitoring Interfaces Screens Active List Active Interfaces List Monitor Interfaces OptionsStatus Interface Status DSL Network Protocol Screens Monitoring → Network Protocol B-D Socket Statistics Network Protocol Options 1UDP Statistics Network Protocol Options 2 TCP Statistics TCP Data Statistics TCP Connection Statistics Network Protocol Options 3IP Statistics Icmp Statistics Icmp Packet Statistics Network Protocol Options 4Snmp Statistics Snmp Authentication Statistics Network Protocol Options 5 DSL Bridge Screens Bridge Table MAC Table User to Display ± Entry number ClientARP Table DSL SN Information Screen Service Node Options Diagnostic Screens Diagnostics and TroubleshootingApplications Screens Diagnostics Options Alarms Card AlarmsSelftest DSL Packet Echo Test Troubleshooting R U U U X Checking Alarms Major Alarms 1 Failure Type Action Ethernet port 1. Check cable connections to the Dslam Major Alarms 2 Failure Type ActionFailure Margin Minor Alarms 1 Failure Type ActionThreshold Minor Alarms 2 Failure Type Action Link Down Slow Performance Network ProblemsExcessive Collisions Cannot Upload Configurations to a Unix Server No Response at Startup Diagnostics and Troubleshooting Download Code and Apply Download Code Tftp Server ConfigurationFully Functional System Deferred Apply Apply Download Download Only System Automatic Immediate Apply Download Code and Apply Download DSL Card Traps TrapsEvent Trap Class Comment Trap # ± MIB Traps Event Trap Class Comment Trap # ± MIB Traps Glossary E1a EthernetEthernet address Filter Service Node PacketPots Splitter Proxy ARP Telnet Terminal emulationTraceRoute Upstream Index IN-1 IN-2