Paradyne 9720, 9788 DHCP Server Commands

C. Router CLI Commands, Codes, and Designations

9700-A2-GB20-20 December 2002 C-15

DHCP Server Commands

Dynamic Host Configuration Protocol (DHCP) server commands are used to

enable or disable the DHCP server, and create or delete a DHCP pool.

Table C-9. DHCP Server Commands (1 of 3)

[no] service dhcp

Minimum Access Level: Administrator

Command Mode: config

Allows you to enable or disable the DHCP server. The DHCP server is enabled by default

but is not active until other DHCP server options are configured. When an IP address is

assigned to a host by the DHCP Server and there is no matching routing table entry, a

host entry for that IP address is created. This entry is deleted from the routing table when

the lease expires or the IP address is relinquished.

When an IP address is assigned to a host on the local Ethernet by the DHCP Server, an

ARP table entry is created mapping that IP address to the corresponding host MAC

address. This entry is deleted from the ARP table when the lease expires or the IP

address is relinquished. This entry is not deleted according to the timeout mechanism that

applies to normal ARP entries.

NOTE: The DHCP Relay and DHCP Server cannot be enabled at the same time.

[no] ip dhcp pool

pool-name

Minimum Access Level: Administrator

Command Mode: config

Allows you to create or delete a DHCP pool and places it in DHCP pool configuration

mode to configure IP DHCP pool parameters. All commands entered while in DHCP pool

configuration mode are applied to the specified DHCP pool. No DHCP pools are

configured by default.

Example: ip dhcp pool pool17

pool-name

– The name of the DHCP pool, as 1–20 ASCII printable characters.

[no] ip dhcp excluded-address

ip-addr

[

end-ip-addr

]

Minimum Access Level: Administrator

Command Mode: config

Allows you to specify a single IP address, or a range of IP addresses, that the DHCP

server should not distribute to clients. The no ip dhcp excluded-address command

allows you to release previously excluded IP addresses for distribution to clients. No IP

addresses are excluded by default. Up to 30 individual or ranges of IP addresses are

supported.

Example: ip dhcp excluded-address 132.53.4.2

ip-addr

– Specifies an IP address to exclude, or the first IP address in a range of excluded

IP addresses.

end-ip-addr

– Specifies the last IP address in a range of excluded IP addresses.

Contents

Main Page Contents About This Guide 1 About FrameSaver DSL Devices 2 User and Command Line Interfaces, and Basic Operation ii 3 Configuration Procedures 4 Configuration Options 5 Configuring the FrameSaver DSL Router 6 Security and Logins iv 7 Operation and Maintenance 8Troubleshooting 9 Setting Up OpenLane for FrameSaver Device vi 10 Setting Up Network Health for FrameSaver Device A Menu Hierarchy B SNMP MIBs, Traps, and RMON Alarm Defaults C Router CLI Commands, Codes, and Designations D Router Command Line Summaries and Shortcuts E Connectors, Cables, and Pin Assignments Page About This Guide Purpose and Intended Audience Document Organization x Section Description Technical Glossary Technical Manuals Library Product-Related Documents Complete Paradyne documentation for this product is available at www.paradyne.com. Select Library Technical Manuals. Document Number Document Title xii Conventions Used Convention Interpretation Italics [ ] {} | About FrameSaver DSL Devices System Overview 1-2 FrameSaver DSL Features Router-Specific Features CSU/DSU-Specific Features CSU/DSU-Specific Features Router-Specific Features Page 1-4 Diagnostic Feature Set Page 1-6 Advanced SLM Feature Set FrameSaver SLV Activation Instructions . in for upgrade information and activation procedures. See Network Configuration Examples 1-8 The illustration below shows a typical network configuration that includes a FrameSaver DSL Router. OpenLane SLM System OpenLane Features Page User and Command Line Interfaces, and Basic Operation 2-2 Logging On Main Menu Ending a Session Security and Logins Configuration Procedures Saving Configuration Options 2-4 Main Menu Menu Hierarchy Screen Work Areas Screen Format Description 2-6 Navigating Menu-Driven User Interface Screens on page 2-9. Keyboard Keys Use the following keyboard keys to navigate within the screen area. Press . . . To . . . Function Keys Screen Work Areas Selecting from a Menu 2-8 Switching Between Screen Areas Function Keys Screen Work Areas Selecting a Field for Input Navigating the Routers CLI Router CLI Commands, Codes, and Designations. Router Command Line Summaries and Shortcuts. CLI Keyboard Keys Page Configuration Procedures 3-2 Basic Configuration From the User Interface Configuration Option Areas Configuration Option Tables FrameSaver DSL CSU/DSU, Models 9783 and 9788, Quick Reference FrameSaver DSL Router, Models 9783 and 9788, Quick Reference 3-4 Accessing and Displaying Configuration Options Main Menu Configuration Changing Configuration Options Security and Logins, Configuration PVC Connections User and Command Line Interfaces, and Basic Operation. Saving Configuration Options 3-6 Configuration Options 4-2 Using the Easy Install Feature Main Menu Easy Install 4-4 Table 4-1. Easy Install Configuration Options (1 of 4) Cell Payload Scrambling DSL Line Rate (Kbps) Network 1 DSL Line Rate (9783) Table 4-1. Easy Install Configuration Options (2 of 4) Network 1 FRF.8 Encapsulation Mode (9783 and 9788) Network 1 FRF.8 Encapsulation Mode (9783 and 9788) Configuring Ethernet Management 4-6 Table 4-1. Easy Install Configuration Options (3 of 4) Table 4-1. Easy Install Configuration Options (4 of 4) 4-8 Entering System Information and Setting the System Clock Main Menu Control System Information Changing the Operating Mode Main Menu Control Change Operating Mode Configuration Option Tables 4-10 Configuring the Overall System The System menu options are described in the following sections: (Advanced SLM Feature Set) Configuring General System Options Configuring Frame Relay and LMI for the CSU/DSU Table 4-2. CSU/DSU Frame Relay and LMI Options (2 of 3) 4-12 Table 4-2. CSU/DSU Frame Relay and LMI Options (3 of 3) Configuring Class of Service Definitions Main Menu Configuration System Class of Service Definitions 4-14 For IDs 27: ASCII Text Entry For IDs 27: Code Point Definitions ASCII Text Configuring Class of Service Definitions on page 4-13 for instructions. Table 4-4. Code Point Definitions ASCII Text Configuring Service Level Verification Options . Advanced SLM Feature Set About FrameSaver DSL Devices Main Menu Configuration System Service Level Verification Table 4-5. Service Level Verification Options (2 of 3) If SLV Feature is enabled: If SLV Feature is disabled: 4-18 Table 4-5. Service Level Verification Options (3 of 3) Configuring General System Options Main Menu Configuration System General Table 4-6. General Options 4-20 Configuring Network Interfaces Main Menu Configuration Network Physical Configuring the Network Physical Interface Table 4-8. Network Physical Interface Options (9783) 4-22 Table 4-9. Network Physical Interface Options (9788) If PSD Mask is Asymmetric (available in future release) and Region is Annex B: If PSD Mask is Symmetric: If PSD Mask is Asymmetric (available in future release) and Region is Annex A: Configuring Frame Relay for the Network Interface Main Menu Configuration Network Frame R elay Configuring DLCI Records for the Network Interface (9720) Main Menu Configuration Network DLCIRecords 4-24 Configuring Circuit Records for the Network Interface (9783, 9788) For the VCI: For the VPI: Main Menu Configuration Network Table 4-11. Circuit Records Options (2 of 3) 4-26 Table 4-11. Circuit Records Options (3 of 3) Configuring ATM for the Network Interface (9783, 9788) DSLAM Type (9783) 9788: 9783 If DSLAM Type is set to a non-Paradyne DSLAM: 9783 If DSLAM Type is set to Paradyne: Configuring the User Data or Virtual Router Port Configuring the CSU/DSUs Data Port Physical Interface Main Menu Configuration Data Ports Physical Table 4-13. CSU/DSU Data Port Physical Interface Options (2 of 2) 4-30 Configuring Frame Relay on the CSU/DSUs Data Port Main Menu Configuration Data Ports Frame Relay Frame Relay Options do not apply to the router. Table 4-14. CSU/DSU Frame Relay Options (1 of 2) Table 4-14. CSU/DSU Frame Relay Options (2 of 2) 4-32 Configuring DLCI Records DLCIRecords Table 4-15. DLCI Records (1 of 3) Table 4-15. DLCI Records (2 of 3) 4-34 Table 4-15. DLCI Records (3 of 3) Configuring PVC Connections Main Menu Configuration PVC Connections Configuring Management PVCs 4-36 Table 4-16. PVC Connections (2 of 2) Configuring the IP Path List Main Menu Configuration IP Path List (Static) Operation and Maintenance IP Path Connection Status 4-38 Setting Up Management and Communication Configuring Node IP Information Table 4-18. Node IP Options (1 of 2) 4-40 Table 4-18. Node IP Options (2 of 2) , Display Conditions Configuring Management PVCs Configuring Circuit Records for the Network Interface (9783, 9788) Configuring Node IP Information Main Menu Configuration Management and Communication Management PVCs 4-42 Table 4-19. Management PVC Options (1 of 4) Table 4-19. Management PVC Options (2 of 4) 4-44 Table 4-19. Management PVC Options (3 of 4) If Payload Managed is disabled: If Payload Managed is enabled: Table 4-19. Management PVC Options (4 of 4) For multiplexed DLCIs: For nonmultiplexed DLCIs: 4-46 Configuring General SNMP Management Main Menu Configuration Management and Communication General SNMP Management Table 4-20. General SNMP Management Options (1 of 2) Table 4-20. General SNMP Management Options (2 of 2) 4-48 Configuring Telnet and/or FTP Sessions Telnet and FTP Sessions Table 4-21. Telnet and FTP Session Options (2 of 3) 4-50 Table 4-21. Telnet and FTP Session Options (3 of 3) Configuring SNMP NMS Security Main Menu Configuration Management and Communication SNMP NMSSecurity 4-52 Table 4-22. SNMP NMS Security Options (2 of 2) Configuring SNMP Traps SNMP MIBs, Traps, and RMON Alarm Defaults See Appendix B, Main Menu Configuration Management and Communication SNMP Traps 4-54 Table 4-23. SNMP Traps Options (2 of 4) linkname Table 4-23. SNMP Traps Options (3 of 4) 4-56 Table 4-23. SNMP Traps Options (4 of 4) Configuring Ethernet Management Main Menu Configuration Management and Communication Ethernet Management or Main Menu Easy Install Ethernet Management Options Screen 4-58 Table 4-24. Ethernet Management Options (2 of 2) Configuring the Communication Port Communication Port Table 4-25. Communication Port Options (1 of 4) 4-60 Table 4-25. Communication Port Options (2 of 4) Table 4-25. Communication Port Options (3 of 4) 4-62 Table 4-25. Communication Port Options (4 of 4) Configuring Node IP Information Configuring the COM Port to Support an External Modem External Modem (Com Port) DB9-to-DB25 Crossover Cable DB25-to-DB25 Crossover Cable Connectors, Cables, and Pin Assignments Page Configuring the FrameSaver DSL Router 5-2 FrameSaver DSL Router Overview Router Command Line Summaries and Shortcuts Router CLI Commands, Codes, and Designations, SNMP MIBs, Traps, and RMON Alarm Defaults IP Routing Address Resolution Protocol Configuring Ethernet Management IP Filtering Dynamic Host Configuration Protocol Server Interface Configuration Network Address Translation IP Options Processing Applications Supported by NAT 5-6 NAT Configuration Example Page 5-8 Network Address Port Translation NAPT Configuration Example Page 5-10 NAT and NAPT Configuration Example Network Address Port Translation Dynamic Host Configuration Protocol Server 5-12 DHCP Server with NAT Configuration Example DHCP Server at Remote Site Configuration Example DHCP Relay Agent 5-14 DHCP Relay Configuration Example Router Security IP Router Filtering Bridge Filtering 5-16 IP Filtering Land Bug Prevention Smurf Attack Prevention Verifying the End-to-End Management Path Provisioning the Router Interface 5-18 Configuring the Router Using Terminal Emulation Uploading and Downloading the Router Configuration Via the CLI Security and Logins 6-2 Limiting Access Controlling Asynchronous Terminal Access Configuring the Communication Port Communication Port Resetting the Unit and Restoring Communication 6-4 Controlling External COM Port Device Access Controlling Router CLI Access Configuring the COM Port to Support an External Modem External Modem (Com Port) Controlling Telnet and FTP Access Limiting Telnet Access Limiting Telnet or FTP Access Over the TS Management Link Configuring Telnet and/or FTP Sessions Telnetand FTP Sessions 6-6 Limiting FTP Access Configuring Telnet and/or FTP Sessions Telnetand FTP Sessions Limiting Telnet or FTP Access Over the TS Management Link 6-8 Controlling SNMP Access Disabling SNMP Access Assigning SNMP Community Names and Access Levels 6-10 Limiting SNMP Access Through IP Addresses Configuring SNMP NMS Security Configuring General SNMP Management General SNMP Management Configuration Options, Controlling Router CLI Access (Control Menu System Information) Router CLI Commands, Codes, and Designations Creating a Login for the User Interface Access Levels (Command Modes) Changing Access Levels Router CLI Commands, Codes, and Designations password Access Levels (Command Modes) password Creating a Login for the User Interface Main Menu Control Administer Logins Resetting the Unit and Restoring Communication Configuring SNMP NMS Security 6-14 Modifying a Login Deleting a Login Main Menu Control Administer Logins Example: Operation and Maintenance 7-2 Ethernet Performance Statistics FTP File Transfers Clearing Performance Statistics Trap Event Log Displaying Identity System Information 7. Operation and Maintenance 9700-A2-GB20-20 December 2002 7-3 Viewing LEDs and Control Leads SHDSL SHDSL 01-16990 SDSL 7-4 Main Menu Status Display LEDs and Control Leads LED Descriptions 7-6 Control Lead Descriptions Table 7-1. LED Descriptions (2 of 2) Label Indication Color What It Means Table 7-2. Control Leads Label Indication What It Means 7-8 Device Messages (Seen at an FTP Activating Software Main Test Activating Software Table 7-3. Device Messages (2 of 5) 7-10 Table 7-3. Device Message s (3 of 5) (Seen at an FTP Upgrading System Software Reason Table 7-3. Device Messages (4 of 5) 7-12 Main Test Table 7-3. Device Messages (5 of 5) Router CLI Messages MaximumDHCPClients Router CLI Commands, Codes, and Designations , for show commands and additional information. Table 7-4. CLI Messages (1 of 5) 7-14 end-ip-address start-ip-address Table 7-4. CLI Messages (2 of 5) sub-interface Table 7-4. CLI Messages (3 of 5) 7-16 Table 7-4. CLI Messages (4 of 5) Table 7-4. CLI Messages (5 of 5) 7. Operation and Maintenance 7-18 Status Information System and Test Status Messages Main Menu Status System and Test Status Main Menu Status System and Test Status Self-Test Results Messages Last Reset Health and Status Messages Test Status Messages Self-Test Results Messages Health and Status Messages atm_link IP_Address IP_ Address Table 7-6. Health and Status Messages (2 of 2) 7-22 Test Status Messages IP Path Connection Status Main Menu Status IP Path Connection Status Configuring the IP Path List IP Path Connection Status Screen Example Table 7-8. IP Path Connection Status Field Status What It Indicates FR Link 7-24 PVC Connection Status (Routers only) Name (CSU/DSUs only) (9783, 9788) Table 7-9. PVC Connection Status Screen (2 of 2) 7-26 Network Interface Status Network Interface Status can be viewed from the Status menu. Main Menu Status Network Interface Status Network Interface Status Screen Example Table 7-10. Network Interface Status IP Routing Table (Management Traffic) Main Menu Status IP Routing Table (Management Traffic) 7-28 Table 7-11. IP Routing Table Values Field What It Indicates name Performance Statistics Main Menu Status Performance Statistics 7-30 Service Level Verification Performance Statistics Main Menu Status Performance Statistics Service Level Verification Table 7-12. SLV Performance Statistics for Multiplexed DLCI (2 of 3) 7-32 Table 7-13. SLV Performance Statistics for IP Enabled DLCI (1 of 2) Table 7-12. SLV Performance Statistics for Multiplexed DLCI (3 of 3) Configuring Class of Service Definitions Table 7-13. SLV Performance Statistics for IP Enabled DLCI (2 of 2) 7-34 DLCI Performance Statistics Main Menu Status PerformanceS tatistics DLCI Additional Performance Statistics for IP Enabled DLCI 7-36 Frame Relay Performance Statistics Main Menu Status PerformanceS tatistics Frame Relay (CSU/DSUs only) Table 7-16. Frame Relay Performance Statistics (2 of 2) 7-38 ATM Performance Statistics (9783, 9788) Access Asynchronous Transfer Mode (ATM) statistics from the Performance Statistics menu. Main Menu Status PerformanceS tatistics ATM VCC Performance Statistics (9783, 9788) Main Menu Status PerformanceS tatistics VCC 7-40 SHDSL Line Performance Statistics (9788) These statistics account for all traffic on the DSL line. Access SHDSL statistics from the Performance Statistics menu. Main Menu Status PerformanceS tatistics xDSL Line Table 7-18. VCC Performance Statistics (2 of 2) Ethernet Performance Statistics Access Ethernet port statistics from the Performance Statistics menu. Main Menu Status PerformanceS tatistics Ethernet 7-42 Clearing Performance Statistics Trap Event Log Main Menu Status Trap Event Log Standards Compliance for SNMP Traps SNMP MIBs, Traps, and RMON Alarm Defaults 7-44 FTP File Transfers Initiating an FTP Session Creating a Login for the User Interface Security and Logins 7-46 Upgrading System Software xxxxxx Determining Whether a Download Is Completed Activating Software Displaying Identity System Information Main Menu Control Select Software Release Upgrading System Software Transferring Collected Data Viewing LMI Captured Packets from the User Interface Troubleshooting 8-2 Problem Indicators Resetting the Unit and Restoring Communication Resetting the Unit from the Control Menu Resetting the Unit By Cycling the Power 8-4 Restoring Communication with an Improperly Configured Unit Resetting the Unit and Restoring Communication Troubleshooting Management Link Feature Configuring Node IP Information Operation and Maintenance Viewing LMI Captured Packets from the User Interface LMI Packet Capture Utility Feature Viewing LMI Captured Packets from the User Interface Control LMI Packet Capture Utility Display LMI Trace Log Tel ne t Control Tel ne t 8-8 Alarms nnnn (Router only) nnnn Table 8-1. Alarm Conditions (2 of 3) 8-10 (minor alarm) nnnn IP_ Address Table 8-1. Alarm Conditions (3 of 3) Viewing the Trap Event Log Troubleshooting Tables 8-12 Device Problems xxxxxxxx Table 8-2. Device Problems Resetting the Unit and Restoring Communication Warranty, Sales, Service, and Training Information ATM P ro ble ms Table 8-3. ATM Problems 8-14 Frame Relay PVC Problems Table 8-4. Frame Relay PVC Problems 8. Troubleshooting 9700-A2-GB20-20 December 2002 8-15 Tests Available The following FrameSaver DSL tests are available. CSU/DSU Test Menu Example Router Test Me nu Exa mple 8-16 Test Timeout Feature Configuring General System Options Starting and Stopping a Test Aborting All Tests Test Timeout Feature Main Menu Test PVC Tests PVC Loopback Main Menu Test Net work PVC Tests Main Menu Test Data Port PVC Tests Send Pattern Main Menu Test [Ne twork PVC Tests/Data Port PVC Tests] Monitor Pattern Main Menu Test [Ne twork PVC Tests/Data Port PVC Tests] Connectivity Main Menu Test Net work PVC Tests Network ATM Loopback 8-22 DTE Loopback Main Menu Test Dat a Port Physical Tests Configuring the CSU/DSUs Data Port Physical Interface Configuration Options. CAUTION: IP Ping Test IP Ping Test Procedure 2 IP Ping Test Procedure 1 IP Ping Test Procedure 2 Table 8-5. Ping Options (1 of 2) Configuring Node IP Information 8-26 Table 8-5. Ping Options (2 of 2) Configuring Class of Service Definitions Page 8-28 IP Ping Test Procedure 1 Main Menu Test IP Ping IP Ping Test Procedure 2 8-30 Lamp Test Test Timeout Feature Main Menu Test La mp Test Setting Up OpenLane for FrameSaver Device 9-2 OpenLane Support of FrameSaver Devices Setting Up the OpenLane SLM System OpenLane SLM Administrators Guide Setting Up FrameSaver Support OpenLane SLM Administrators Guide 9-4 Ordering Advanced SLM Feature Set Activations To Find Your License Key Number The Activation Certificate 9-6 Administering and Managing Advanced SLM Activations Entering an Activation Certificate Checking Activation Certificate Status 9-8 Scheduling Activations Checking the Status of Scheduled Activations Canceling Scheduled Activations Accessing and Printing the Certificate Summary Report Page Setting Up Network Health for FrameSaver Device 10-2 Installation and Setup of Network Health Network Health Installation Guide Discovering FrameSaver Elements elements Discovering Elements 10-4 Configuring the Discovered Elements Discovering Elements Grouping Elements for Reports Managing Groups and Group Lists 10-6 Generating Reports for a Group Running Reports from the Console Network Health Reports Guide About Service Level Reports About At-a-Glance Reports Reports Applicable to FrameSaver Devices 10-8 Page 10-10 A Menu Hierarchy Menus A-2 FrameSaver DSL CSU/DSUs Menu Structure Sta tus Test Configuration Control Easy Install A-4 FrameSaver DSL Routers Menu Structure Sta tus Test Configuration Control Easy Install Page B SNMP MIBs, Traps, and RMON Alarm Defaults B-2 MIB Support Downloading MIBs and SNMP Traps Support Online Technical Support System Group (mib-2) FrameSaver Units sysDescr (system 1) (hardware version in hhhh-hhh format) [model number-C or R] (MM.mm.bb [MM=Major.mm=minor.bb=build] format) Interfaces Group (mib-2) Paradyne Indexes to the Interface Table (ifTable) NetScout Probe Indexes to the Interface Table (ifTable) DLCI number interfacenumber B-6 Standards Compliance for SNMP Traps Trap: warmStart Trap: authenticationFailure B-8 Trap: linkUp and linkDown (continued) Strings: String: B-10 Trap: enterprise-Specific B-12 String: s String: Table B-7. enterprise-Specific Traps and Variable-Bindings (2 of 3) Trap: RMON-Specific Two traps are defined to support the Alarm and Events Groups of RMON. See RMON Alarm and Event Defaults on page B-14 for the default values that will generate RMON-specific traps. Table B-7. enterprise-Specific Traps and Variable-Bindings (3 of 3) RMON Alarm and Event Defaults Trap: RMON-Specific Standards Compliance for SNMP Traps Network Physical Interface Alarm Defaults Frame Relay Link Alarm Defaults B-16 Table B-10. Frame Relay Link Alarm Defaults (2 of 2) Sample Type 1MIB/Tag/OID2Interval Event DLCI Alarm Defaults Type1MIB/Tag/OID2Inte rval Event B-18 Table B-11. DLCI Alarm Defaults (2 of 2) Type1MIB/Tag/OID2Inte rval Event OID Cross-References B-20 Table B-12. History OID Cross-Reference (2 of 4) Table B-12. History OID Cross-Reference (3 of 4) B-22 Table B-12. History OID Cross-Reference (4 of 4) Page B-24 Table B-13. Alarm OID Cross-Reference (2 of 2) ObjectID (OID)1Item MIB/Tag C Router CLI Commands, Codes, and Designations x.x.x.x Italics CLI Commands C-2 Pager Command Access Control Commands Controlling Router CLI Access Security and Logins C-4 Configuration Commands save Interface Commands C-6 Table C-4. Interface Commands (2 of 3) ip address encapsulation-protocol encapsulation-type dlci-num C-8 IP Routing Commands intf-num next-hop-ip .sub-intf-num next-hop-ip Bridge Commands aging-time route-protocol span-tree-priority aging-time C-10 Table C-6. Bridge Commands (2 of 2) [no] bridge-group out-access-list-200num in-access-list-200num ARP Commands ip-address mac-address arp-type mac-address arp-type ip-address NAT Commands Page C-14 Table C-8. NAT Commands (3 of 3) clear ip nat translation * DHCP Server Commands ip-addr end-ip-addr [ ip-addr C-16 minutes domain-name minutes hours network-num prefix-length netmask network-num C-18 DHCP Relay Agent Commands max-dhcp-clients Filter (access-list) Commands C-20 Table C-11. Filter Commands (2 of 4) Table C-11. Filter Commands (3 of 4) C-22 Table C-11. Filter Commands (4 of 4) access-list-1-199num [no] ip access-group [in | out] Diagnostic Commands bytes intf-num source-ip protocol C-24 Table C-12. Diagnostic Commands (2 of 2) bytes sub-intf-num intf-num Show Commands Show commands allow you to display information. Table C-13. Show Commands (1 of 4) show arp x.x.x.x time xx:xx:xx:xx:xx:xx xx:xx:xx:xx:xx:xx Configuring the Router Using Terminal Emulation C-26 Table C-13. Show Commands (2 of 4) show configuration {saved | unsaved} .sub-intf-num [ show ip dhcp binding [ Table C-13. Show Commands (3 of 4) show ip nat translations show ip route [ C-28 Ethernet Type Codes C-30 Table C-14. Ethernet Type Codes (Hex) (2 of 2) Type Code Description Type Code Description Protocol and Port Designations The following tables are used for filtering. ICMP Designations C-32 Table C-15. ICMP Designations (2 of 2) Type Code ICMP Message Description TCP Port Designations C-34 UDP Port Designations D Router Command Line Summaries and Shortcuts Router CLI Commands, Codes, and Designations. CLI Command Default Settings CLI Summaries Show Command Summary show ip route [ s how ip dhcp b .sub-intf-num intf-type intf-num Access Control and System Level Command Summary D-4 CLI Command Summary do n o dn dn no default-router [ Page D-6 CLI Command Default Settings E Connectors, Cables, and Pin Assignments E-2 Rear Panels 01-16971 01-16690-01 02-17312 Figure E-3. Model 9788 CSU/DSU Rear Panel Page E-4 DSL Network Interface and Cable The following shows the cables pin assignments and the purpose of each. Table E-1. DSL Network Interface Connector Pin # Signal Model 9783 COM Port Connector Model 9720 and 9788 COM Port Connector E-6 Ethernet Port Connector Model 9720 and 9783 CSU/DSU Data Port Connector Standard V.35 Straight-through Cable E-8 Model 9788 CSU/DSU Data Port Connector 9700-A2-GB20-20 December 2002 E-9 EIA-530-A-to-V.35 Adapter E-10 EIA-530-A-to-X.21 Adapter Configuring an External Modem DB25-to-DB25 Crossover Cable DB9-to-DB25 Crossover Cable E-12 DB25-to-DB25 Crossover Cable Ethernet Port Connector on page E-6 to configure an external modem. This does not apply to the router. DB9-to-DB25 Crossover Cable Ethernet Port Connector on page E-6 to configure an external modem. This does not apply to the router. Page F Technical Specifications F-2 Table F-1. FrameSaver DSL Technical Specifications (2 of 2) Specification Criteria G Equipment List Cables See Equipment G-2 Page G-4 xxx Cables This table lists cables you can order. Description Part Number Feature Number For connection to an external device. For use in the U.S. For connection to an external device with a DB9connector. Page Index Numerics A B IN-2 C D IN-4 E F G H IN-6 I K L M IN-8 N O P IN-10 Q R S Page IN-12 T U V W X