Manuals / Patton electronic / Computer Equipment / Modem

Patton electronic 3202 manual Safety when working with electricity, tected by a circuit breaker

Models: 3202

1 106

Download 106 pages 9.27 Kb

Page 14

Safety when working with electricity

Model 3202 Getting Started Guide	About this guide

Safety when working with electricity

The Model 3202 contains no user serviceable parts. The equipment shall be returned to Patton Electronics for repairs, or repaired by qualiﬁed service per- sonnel. Opening the Model 3202 case will void the warranty.

WARNING

Mains Voltage: Do not open the case the when the power cord is attached. Line voltages are present within the power supply when the power cords are

connected. The mains outlet that is utilized to power the device shall be WARNING within 10 feet (3 meters) of the device, shall be easily accessible, and pro-

tected by a circuit breaker.

For AC powered units, ensure that the power cable used meets all applicable standards for the country in which it is to be installed, and that it is connected to a wall outlet which has earth ground.

	WARNING
		Hazardous network voltages are present in WAN ports regardless of whether
		power to the Model 3202 is ON or OFF. To avoid electric shock, use caution
	WARNING	when near WAN ports. When detaching the cables, detach the end away from
	WARNING	the Model 3202 ﬁrst.
		the Model 3202 ﬁrst.

Do not work on the system or connect or disconnect cables during periods of lightning activity.

WARNING

In accordance with the requirements of council directive 2002/ 96/EC on Waste of Electrical and Electronic Equipment (WEEE), ensure that at end-of-life you separate this product from other waste and scrap and deliver to the WEEE collection system in your country for recycling.

Preventing Electrostatic Discharge Damage

When starting to install interface cards place the interface card on its shielded plastic bag if you lay it on your bench.

Electrostatic Discharge (ESD) can damage equipment and impair electrical circuitry. It occurs when electronic

14

Image 14

Patton electronic 3202 manual Safety when working with electricity, Preventing Electrostatic Discharge Damage

Contents

Getting Started Guide RocketLink Model2Base-TL Ethernet First Mile G.SHDSL Modem Sales Ofﬁce +1 3017622 Rickenbacker Drive Gaithersburg, MD 20879 USA Tel +1 301 Summary Table of Contents Table of Contents Table of ContentsSummary Table of Contents Hardware installation4 Web configuration Table of Contents5 Console and Telnet configuration 6 Contacting Patton for assistance A Compliance informationSpecifications Port pin-outsList of Figures Model 3202 Getting Started Guide List of Tables Structure About this guideAudience Note A note presents additional information or interesting sidelights Precautionsimpaired functioning tected by a circuit breaker Safety when working with electricityPreventing Electrostatic Discharge Damage the Model 3202 ﬁrstProtect the unit from moisture, vapors, and corrosive liquids General observationsClean the case with a soft slightly moist anti-static cloth Garamond blue type Typographical conventions used in this documentGeneral conventions Chapter contents Chapter 1 General informationModel 3202 overview RocketLink Model 3202 front panelLED descriptions Model 3202 rear panel Port descriptionsReset button Ground terminalChapter 2 Applications overview Chapter contentsFigure 4. Model 3202 application IntroductionTypical application Distance Chart Model 3202/4W 4 Wire/2 Pair Distance chartsDistance Chart 3200 Series Per Wire Pair Distance Chart Model 3202/8W 8 Wire/4 Pair Chapter contents Hardware installationChapter Introduction Planning the installationCreate a network diagram Gather IP related information IP related information Network diagramAC Power Mains Location and mounting requirements Installing the ModelConnecting cables Unpacking the ModelGrounding the Model 3202 and connecting power Console conﬁguration requirements Conﬁguring the ModelWeb conﬁguration requirements Telnet conﬁguration requirementsChapter Web conﬁgurationChapter contents Configuration Tool 4 Web configurationSNMP Administration UpgradeSystem Login Setting Up the WMITCP/IP setup Introduction4 Web configuration Basic Conﬁguration OptionsOperation mode and MGMT port Basic Configuration OptionsDHCP server Subnet Mask Host Name SOHOPage Review and save basic setup changes IP Address Subnet Mask Gateway DNS Server 1 DNS Server 2Line Type Advanced Conﬁguration OptionsLINE Annex TypeSNR Margin TCPAM TypeMain Rate Line ProbeVLAN Backbone 4 Web configurationAdvanced Configuration Options WAN4 WAN5Figure 17. VLAN tag ﬁeld 802.1Q Tag-Based VLANFigure 16. 802.1Q Tag-Based VLAN page Figure 18. 802.1Q VLAN diagram 802.1Q VLANually or dynamically using Generic VLAN Routing Protocol GVRP. However, if you want a port on this Model 3202 to participate in one or more VLANs, but none of the intermediate network devices nor the host at the other end of the connection supports VLANs, then you should add this port to the VLAN as an untagged port Port-Based VLAN Figure 19. Port-Based VLAN pagePort-Based QinQ TPID Tag Protocol Identiﬁer Enter 33024 for IEEE802.1QQuality of Service QoS Port Based Priority Figure 23. QoS - Port Based Priority pageFigure 25. IEEE 802.1Q Tagged Frame for Ethernet VLAN Tag PriorityFigure 24. QoS - VLAN Tag Priority page 0 default IP DSCP Priority 41,25 Queue 40,35 Queue 4,5 Queue 6,7 QueueBest effort Stays the sameused for IP routing ProtocolsExpress Forwarding EF Figure 28. QoS - IP DSCP Priority page Figure 30. Rate Control options Rate ControlFigure 29. Rate Control page MGMT Status Status OptionsLINE Status LAN Status Administration OptionsSecurity Administration Figure 35. Model 3202 conﬁguration modes User ProﬁlesRemote Management Hosts Figure 36. Remote Management Host sectionSNMP Administration Community Pool Click Modify to set up community poolsSystem Information Utility OptionsTrap Host Pool Conﬁguration Tool Figure 42. Upgrade page UpgradeLogout Figure 43. Logout pageUtility Options RestartThe following screen displays Chapter Console and Telnet conﬁgurationChapter contents 5 Console and Telnet configuration Model 3202 Getting Started GuideLog in to the console interface Log in using TelnetInterface commands Table 15. Console settingsWindow structure Main Menu Tree Menu tree for authorized usersFigure 48. Main screen for authorized users Menu tree for unauthorized users5 Console and Telnet configuration Figure 49. Main menu for unauthorized usersEnable Command Menu Setup Command Menu G.SHDSLMaximum Main Rate ModeLink Annex TypeLine Probe ClearUse the clear command to reset the CRC error count Mode Disable 802.1Q Tag VLAN Port-Based VLANVLAN Table 22. VLAN Mode OptionsUse the pvid command to change the member port to untagged members LAN1 Port link type TAB Select AccessModel 3202 Getting Started Guide LAN2Mode Table 25. Queue Weight Options Queue WeightQueue Schedule Table 26. Queue Schedule TypesPort-Based Priority QoS VLAN Tag Priority QoSIP DSCP Priority QoS Set up queue index 0, 1, 2 or 3 on each DSCPList Rateaddress MGMT IP address and subnet mask MGMTDHCP DHCP Server DHCP Fixed HostHost Name Factory DefaultDNS Proxy Interface Status Status Command MenuG.SHDSL Status Show Command Menu Write CommandReboot Command Ping CommandModify/Add User Administration Command MenuUser Proﬁle Legal IP Address Pool SecurityTelnet TCP Port SNMP CommunityTrap host Validate Set to Enable or DisableAccess right Set to Read only, Read Write or Denied 5 Console and Telnet configurationSupervisor Password Version Set to Disable, Version 1 or VersionSupervisor Password and ID Supervisor IDBackup system conﬁguration Utility Command MenuUpgrade main software Restore system conﬁgurationExit Command Exit CommandModel 3202 Getting Started Guide5 Console and Telnet configuration Press “y” to exit the system. A conﬁrmation screen displaysChapter 6 Contacting Patton for assistance Chapter contentsContact information Warranty Service and Returned Merchandise Authorizations RMAsWarranty coverage IntroductionReturn for credit policy Out-of-warranty serviceReturns for credit RMA numbersAppendix A Compliance information Chapter contentsCE Declaration of Conformity ComplianceRadio and TV interference FCC Part Authorized European RepresentativeAppendix B Speciﬁcations Chapter contentsManagement Connector G.SHDSL ConnectorEthernet Connector G.SHDSL SpeciﬁcationsDimensions Front Panel IndicatorsPower Supply WeightAppendix C Port pin-outs Chapter contentsIntroduction Console portPins 1 & 3 are Model 3202 Getting Started GuideModel 3202 Getting Started Guide EthernetNote Pins not listed are not used C Port pin-outs