Conﬁguring the Model | Patton electronic 3202 instruction

Model 3202 Getting Started Guide	3 • Hardware installation

Conﬁguring the Model 3202

There are three different ways you can conﬁgure the Model 3202: the serial console, Telnet, or a web browser.

Web conﬁguration requirements

Make sure that the PC you use for conﬁguration has an Ethernet adapter and TCP/IP installed.

The Model 3202 provides a browser interface that allows you to conﬁgure and manage the modem. After you set up the IP address for the 3202, you can access the modem's Web interface applications directly in your browser by entering the IP address. You can then use your Web browser to manage and conﬁgure the unit from a PC.

Note For detailed information on conﬁguring the Model 3202 through the

Web interface, see Chapter 4, “Web conﬁguration” on page 32.

Console conﬁguration requirements

To conﬁgure the Model 3202 through the serial console, you can directly connect a terminal or a PC equipped with a terminal-emulation program (such as Hyper Terminal) to the modem's console port.

Use the supplied serial cable (RJ-45 to DB9F) to connect the Model 3202 to a PC. After marking the connec- tion, conﬁgure the terminal-emulation program to use the following parameters:

•9600 bps

•8 data bits

•no parity

•1 stop bit

Note For detailed information on conﬁguring the Model 3202 through the serial console, see Chapter 5, “Console and Telnet conﬁguration” on page 65.

Telnet conﬁguration requirements

Make sure that the PC you use for conﬁguration has an Ethernet adapter and TCP/IP installed. The Model 3202 supports Telnet for remote conﬁguration. The command is “telnet 192.168.1.1” . When prompted for the username and password for remote login, use admin for username and admin for password. All display screens are the same as serial console conﬁguration.

The default IP address is 192.168.1.1, but you may change the IP address for your application.

Note For detailed information on conﬁguring the Model 3202 through Telnet, see Chapter 5, “Console and Telnet conﬁguration” on page 65.

Configuring the Model 3202

31

Image 31

Patton electronic 3202 manual Conﬁguring the Model, Web conﬁguration requirements, Console conﬁguration requirements

Contents

RocketLink Model Mailsupport@patton.com Summary Table of Contents Table of Contents Web configuration Console and Telnet configuration Contacting Patton for assistance Port pin-outs List of Figures Model 3202 Getting Started Guide List of Tables Audience About this guideStructure Impaired functioning Precautions Model 3202 ﬁrst Safety when working with electricityPreventing Electrostatic Discharge Damage Tected by a circuit breaker General observations Clean the case with a soft slightly moist anti-static cloth General conventions Typographical conventions used in this document General information Chapter contents Model Model 3202 overview LAN 1-4100M Model 3202 front panelLED descriptions WAN 1-4 Link Port descriptions Model 3202 rear panelDC 9V 2A Ground terminal Reset button Applications overview Typical application Introduction Distance Chart 3200 Series Per Wire Pair Distance chartsDistance Chart Model 3202/4W 4 Wire/2 Pair Distance Chart Model 3202/8W 8 Wire/4 Pair Hardware installation Planning the installation AC Power Mains Network diagramIP related information Unpacking the Model Installing the ModelConnecting cables Location and mounting requirements Grounding stud Grounding the Model 3202 and connecting power Telnet conﬁguration requirements Conﬁguring the ModelWeb conﬁguration requirements Console conﬁguration requirements Web conﬁguration Web configuration TCP/IP setup Setting Up the WMISystem Login Basic Conﬁguration Options Operation mode and Mgmt port Dhcp server Subnet Mask Host Name Soho LAN IP Address Subnet Mask Gateway DNS Server 1 DNS Server 2 Review and save basic setup changes Line Type Advanced Conﬁguration OptionsAnnex Type SNR Margin Wire modelTcpam Type Main Rate Vlan VID 1Q Tag-Based Vlan 802.1Q Tag-Based Vlan 802.1Q Vlan Web configuration Port-Based Vlan Port-Based Vlan Tpid Tag Protocol Identiﬁer Enter 33024 for IEEE802.1Q Port-Based QinQ Quality of Service QoS QoS Port Based Priority Port Based Priority QoS Vlan Tag Priority Vlan Tag Priority Default IP Dscp Priority Service by WRR Throughput Normal High Reliability Delay NormalStays the same link layer and routing protocol keep alive Class QoS IP Dscp Priority Rate Control Rate Control Line Status Status OptionsMgmt Status Security Administration Administration OptionsLAN Status Remote Management Hosts User Proﬁles Snmp Administration Snmp Administration Snmp community pool conﬁguration Community Pool Trap Host Pool Utility OptionsSystem Information Conﬁguration Tool Conﬁguration Tool Logout Upgrade Restart Restart Dhcp Server Dhcp Fixed Host DNS Proxy Host Name Console and Telnet conﬁguration Console and Telnet configuration Log in to the console interface Log in using TelnetInterface commands Ctrl + C Quit conﬁguring the item Ctrl +Q Access help Console/Telnet Menu Window structure Menu tree for authorized users Main Menu Tree Main screen for authorized users Menu tree for unauthorized users Enable Command Menu Setup Command Menu Link ModeMaximum Main Rate IP Address Subnet Mask Clear Vlan Mode Setup Command Menu Pvid QoS QoS Mode QoS Mode Weight Value Queue WeightQueue Schedule Vlan Tag Priority QoS Port-Based Priority QoS Vlan Tag Index 0 1 2 3 4 5 6 Queue Index IP Dscp Priority QoS Port Snifﬁng ListRate Port Mgmt Dhcp Fixed Host Dhcp Server DNS Proxy Factory DefaultHost Name Shdsl Status Command MenuShdsl Status Interface Status Conﬁg Show Command MenuWrite Command System Ping Command Reboot Command User Proﬁle Administration Command MenuModify/Add User Telnet TCP Port SecurityLegal IP Address Pool Community Snmp Denied Trap hostReadOnly ReadWrite Supervisor Password Supervisor Password and IDSupervisor ID Restore system conﬁguration Utility Command MenuUpgrade main software Backup system conﬁguration Exit Command Contacting Patton for assistance Contact information Warranty coverage RMA numbers Out-of-warranty serviceReturns for credit Return for credit policy Appendix a Compliance information Authorized European Representative ComplianceRadio and TV interference FCC Part CE Declaration of Conformity Appendix B Speciﬁcations Shdsl Speciﬁcations Shdsl ConnectorEthernet Connector Management Connector Weight Front Panel IndicatorsPower Supply Dimensions Appendix C Port pin-outs EIA-561 RJ-45 8-pin port Console port Ethernet