Grounding stud | Patton electronic 3202 manual

Model 3202 Getting Started Guide	3 • Hardware installation

Grounding the Model 3202 and connecting power

In connecting to the power source, it is important to establish a good grounding connection ﬁrst, then the power connection. Do the following:

1.Assemble a ground wire using #10 AWG wire with green-colored insulation and two ring terminals. Make the wire long enough to reach one of the following earth ground sources:

–The building ground rod (generally located at the site’s main service entrance)

–A sprinkler system pipe

–A cold-water pipe

–Building structural steel

4

LINE

Grounding stud

Figure 6. Grounding stud

2.Install the grounding wire between the grounding stud (see ﬁgure 6) and the grounding source.

3.Connect the power adapter to the DC 9V port on the Model 3202, and then connect to the power source.

WARNING

WARNING

Mains Voltage: Do not open the case the when the power cord is attached. Line voltages are present within the power supply when the power cords are connected. The mains outlet that is utilized to power the device shall be within 10 feet (3 meters) of the device, shall be easily accessible, and pro- tected by a circuit breaker.

The Model 3202 is not shipped with power cables. For AC powered units, ensure that the power cable used meets all applicable standards for the coun- try in which it is to be installed, and that it is connected to a wall outlet which has earth ground.

The power supply automatically adjusts to accept an input volt- age from 100 to 240 VAC(50/60 Hz).

IMPORTANT

Installing the Model 3202

30

Image 30

Patton electronic manual Grounding the Model 3202 and connecting power, Grounding stud

Contents

RocketLink Model Mailsupport@patton.com Summary Table of Contents Table of Contents Web configuration Console and Telnet configuration Contacting Patton for assistance Port pin-outs List of Figures Model 3202 Getting Started Guide List of Tables About this guide AudienceStructure Precautions Impaired functioning Tected by a circuit breaker Safety when working with electricityPreventing Electrostatic Discharge Damage Model 3202 ﬁrst Clean the case with a soft slightly moist anti-static cloth General observations Typographical conventions used in this document General conventions Chapter contents General information Model 3202 overview Model WAN 1-4 Link Model 3202 front panelLED descriptions LAN 1-4100M Model 3202 rear panel Port descriptionsDC 9V 2A Reset button Ground terminal Applications overview Introduction Typical application Distance charts Distance Chart 3200 Series Per Wire PairDistance Chart Model 3202/4W 4 Wire/2 Pair Distance Chart Model 3202/8W 8 Wire/4 Pair Hardware installation Planning the installation Network diagram AC Power MainsIP related information Location and mounting requirements Installing the ModelConnecting cables Unpacking the Model Grounding the Model 3202 and connecting power Grounding stud Console conﬁguration requirements Conﬁguring the ModelWeb conﬁguration requirements Telnet conﬁguration requirements Web conﬁguration Web configuration Setting Up the WMI TCP/IP setupSystem Login Operation mode and Mgmt port Basic Conﬁguration Options Subnet Mask Host Name Soho Dhcp server LAN Review and save basic setup changes IP Address Subnet Mask Gateway DNS Server 1 DNS Server 2 Advanced Conﬁguration Options Line TypeAnnex Type Main Rate Wire modelTcpam Type SNR Margin Vlan VID 802.1Q Tag-Based Vlan 1Q Tag-Based Vlan 802.1Q Vlan Web configuration Port-Based Vlan Port-Based Vlan Port-Based QinQ Tpid Tag Protocol Identiﬁer Enter 33024 for IEEE802.1Q Quality of Service QoS Port Based Priority QoS Port Based Priority Vlan Tag Priority QoS Vlan Tag Priority Default Service by WRR IP Dscp Priority Class Delay NormalStays the same link layer and routing protocol keep alive Throughput Normal High Reliability QoS IP Dscp Priority Rate Control Rate Control Status Options Line StatusMgmt Status Administration Options Security AdministrationLAN Status User Proﬁles Remote Management Hosts Snmp Administration Snmp Administration Community Pool Snmp community pool conﬁguration Utility Options Trap Host PoolSystem Information Conﬁguration Tool Conﬁguration Tool Upgrade Logout Restart Restart Console and Telnet conﬁguration Dhcp Server Dhcp Fixed Host DNS Proxy Host Name Console and Telnet configuration Ctrl + C Quit conﬁguring the item Ctrl +Q Access help Log in using TelnetInterface commands Log in to the console interface Window structure Console/Telnet Menu Main Menu Tree Menu tree for authorized users Menu tree for unauthorized users Main screen for authorized users Enable Command Menu Setup Command Menu Mode LinkMaximum Main Rate Clear IP Address Subnet Mask Vlan Mode Setup Command Menu Pvid QoS Mode QoS Queue Weight QoS Mode Weight ValueQueue Schedule Port-Based Priority QoS Vlan Tag Priority QoS IP Dscp Priority QoS Vlan Tag Index 0 1 2 3 4 5 6 Queue Index Port ListRate Port Snifﬁng Mgmt Dhcp Server Dhcp Fixed Host Factory Default DNS ProxyHost Name Interface Status Status Command MenuShdsl Status Shdsl System Show Command MenuWrite Command Conﬁg Reboot Command Ping Command Administration Command Menu User ProﬁleModify/Add User Security Telnet TCP PortLegal IP Address Pool Snmp Community ReadWrite Trap hostReadOnly Denied Supervisor Password and ID Supervisor PasswordSupervisor ID Backup system conﬁguration Utility Command MenuUpgrade main software Restore system conﬁguration Exit Command Contacting Patton for assistance Warranty coverage Contact information Return for credit policy Out-of-warranty serviceReturns for credit RMA numbers Appendix a Compliance information CE Declaration of Conformity ComplianceRadio and TV interference FCC Part Authorized European Representative Appendix B Speciﬁcations Management Connector Shdsl ConnectorEthernet Connector Shdsl Speciﬁcations Dimensions Front Panel IndicatorsPower Supply Weight Appendix C Port pin-outs Console port EIA-561 RJ-45 8-pin port Ethernet