Reset button, Ground terminal | Patton electronic 3202 instruction

Model 3202 Getting Started Guide	1 • General information

Reset button

•To restart the unit with the current startup conﬁguration—Press for less than 1 second and release the Reset button. The Model 3202 will restart with the current startup conﬁguration.

•To restart the unit with factory default conﬁguration—Press the Reset button for 5 seconds until the Power LED starts blinking. The unit will restart with factory default conﬁguration.

•To restart the unit in bootloader mode (to be used only by trained RocketLink technicians)—Start with the unit powered off. Press and hold the Reset button while applying power to the unit. Release the Reset button when the Power LED starts blinking so the unit will enter bootloader mode.

Ground terminal

The marked lug or terminal should be connected to the building protective earth bus.The func- tion of protective earth does not serve the purpose of providing protection against electrical shock, but instead enhances surge suppression on the DSL lines for installations where suitable bonding facilities exist.The connector type is M3 machine screw.

Model 3202 rear panel

21

Image 21

Patton electronic 3202 manual Reset button, Ground terminal

Contents

RocketLink Model Mailsupport@patton.com Summary Table of Contents Table of Contents Web configuration Console and Telnet configuration Contacting Patton for assistance Port pin-outs List of Figures Model 3202 Getting Started Guide List of Tables About this guide AudienceStructure Impaired functioning Precautions Preventing Electrostatic Discharge Damage Safety when working with electricityTected by a circuit breaker Model 3202 ﬁrst General observations Clean the case with a soft slightly moist anti-static cloth General conventions Typographical conventions used in this document General information Chapter contents Model Model 3202 overview LED descriptions Model 3202 front panelWAN 1-4 Link LAN 1-4100M Model 3202 rear panel Port descriptionsDC 9V 2A Ground terminal Reset button Applications overview Typical application Introduction Distance charts Distance Chart 3200 Series Per Wire PairDistance Chart Model 3202/4W 4 Wire/2 Pair Distance Chart Model 3202/8W 8 Wire/4 Pair Hardware installation Planning the installation Network diagram AC Power MainsIP related information Connecting cables Installing the ModelLocation and mounting requirements Unpacking the Model Grounding stud Grounding the Model 3202 and connecting power Web conﬁguration requirements Conﬁguring the ModelConsole conﬁguration requirements Telnet conﬁguration requirements Web conﬁguration Web configuration Setting Up the WMI TCP/IP setupSystem Login Basic Conﬁguration Options Operation mode and Mgmt port Dhcp server Subnet Mask Host Name Soho LAN IP Address Subnet Mask Gateway DNS Server 1 DNS Server 2 Review and save basic setup changes Advanced Conﬁguration Options Line TypeAnnex Type Tcpam Type Wire modelMain Rate SNR Margin Vlan VID 1Q Tag-Based Vlan 802.1Q Tag-Based Vlan 802.1Q Vlan Web configuration Port-Based Vlan Port-Based Vlan Tpid Tag Protocol Identiﬁer Enter 33024 for IEEE802.1Q Port-Based QinQ Quality of Service QoS QoS Port Based Priority Port Based Priority QoS Vlan Tag Priority Vlan Tag Priority Default IP Dscp Priority Service by WRR Stays the same link layer and routing protocol keep alive Delay NormalClass Throughput Normal High Reliability QoS IP Dscp Priority Rate Control Rate Control Status Options Line StatusMgmt Status Administration Options Security AdministrationLAN Status Remote Management Hosts User Proﬁles Snmp Administration Snmp Administration Snmp community pool conﬁguration Community Pool Utility Options Trap Host PoolSystem Information Conﬁguration Tool Conﬁguration Tool Logout Upgrade Restart Restart Dhcp Server Dhcp Fixed Host DNS Proxy Host Name Console and Telnet conﬁguration Console and Telnet configuration Interface commands Log in using TelnetCtrl + C Quit conﬁguring the item Ctrl +Q Access help Log in to the console interface Console/Telnet Menu Window structure Menu tree for authorized users Main Menu Tree Main screen for authorized users Menu tree for unauthorized users Enable Command Menu Setup Command Menu Mode LinkMaximum Main Rate IP Address Subnet Mask Clear Vlan Mode Setup Command Menu Pvid QoS QoS Mode Queue Weight QoS Mode Weight ValueQueue Schedule Vlan Tag Priority QoS Port-Based Priority QoS Vlan Tag Index 0 1 2 3 4 5 6 Queue Index IP Dscp Priority QoS Rate ListPort Port Snifﬁng Mgmt Dhcp Fixed Host Dhcp Server Factory Default DNS ProxyHost Name Shdsl Status Status Command MenuInterface Status Shdsl Write Command Show Command MenuSystem Conﬁg Ping Command Reboot Command Administration Command Menu User ProﬁleModify/Add User Security Telnet TCP PortLegal IP Address Pool Community Snmp ReadOnly Trap hostReadWrite Denied Supervisor Password and ID Supervisor PasswordSupervisor ID Upgrade main software Utility Command MenuBackup system conﬁguration Restore system conﬁguration Exit Command Contacting Patton for assistance Contact information Warranty coverage Returns for credit Out-of-warranty serviceReturn for credit policy RMA numbers Appendix a Compliance information Radio and TV interference FCC Part ComplianceCE Declaration of Conformity Authorized European Representative Appendix B Speciﬁcations Ethernet Connector Shdsl ConnectorManagement Connector Shdsl Speciﬁcations Power Supply Front Panel IndicatorsDimensions Weight Appendix C Port pin-outs EIA-561 RJ-45 8-pin port Console port Ethernet