Manuals / Paxar / Computer Equipment / Printer

Paxar 4 manual Operator’s Handbook, Close the printer and turn the printer on

Models: 4

1 54

Download 54 pages 11.95 Kb

Page 23

Image 23

5.Close the printer and turn the printer on.

9490 Operator’s Handbook

4.Feed the labels over the peel bar and through the lower opening in the supply guide.

Label

Guide Upper

Opening

Lower

Opening

5.Close the printer and turn the printer on.

6.Wait until the LED flashes one time (about five seconds) and then press the trigger. The printer advances the first label to the correct position for printing. When you print, labels peel automatically through the top opening in the supply guide and the backing paper exits out the bottom opening.

n The LED slowly alternates flashing amber and green to indicate the printer is out of labels. When this happens, load a new roll of labels and press the trigger to clear the error.

2-10	TC9490OH Rev. C 3/97

Page 23

Image 23

Paxar 4 manual Operator’s Handbook, Close the printer and turn the printer on

Contents

1995 Monarch Marking Systems, Inc. All rights reserved Operator’s HandbookMonarch Renegade 4 Printer TC9490OH Rev. CB 3/01Trademarks CANADIAN D.O.C. WARNINGPage Table of Contents 9490 Operator’s Handbook Additional Optional Manuals ChapterGetting Started 9490 Operator’s Handbook Charging the BatteryAudience Chapter 1. Getting Started 9490 Operator’s Handbook To charge the batteryLatch Tab Finger Depression Loading and Removing the BatteryChapter 1. Getting Started 9490 Operator’s Handbook Connecting the AC Power SupplyChapter 1. Getting Started Connecting the Shoulder Strap9490 Operator’s Handbook Using the Trigger and LEDChapter Loading SuppliesOpening the Printer 2. Pull the supply guide forward and down as shown 3. Tip the printhead assembly up and over the platen roller as shownPrinthead Assembly Platen Roller Pinch Rollers Peel Bar 9490 Operator’s HandbookLatches Chapter 2. Loading SuppliesPrinthead Assembly 4. Slide the latches on the back of the printer toward the center9490 Operator’s Handbook Loading RibbonChapter 2. Loading Supplies Reloading a Ribbon Cassetten Do Not wrinkle or crush the ribbon 9490 Operator’s HandbookChapter 2. Loading Supplies Loading for Peel ModeLoading Supplies TC9490OH Rev. C 3/97 9490 Operator’s HandbookSupply Holder Arrow Width of Supply Tabs TC9490OH Rev. C 3/97 Chapter 2. Loading Suppliesn Make sure the labels turn freely in the supply well Supply Holder5. Close the printer and turn the printer on 9490 Operator’s HandbookChapter 2. Loading Supplies Loading for Non-Peel Mode2-11 Supply Holder 9490 Operator’s Handbookn Make sure the supplies turn freely in the supply well 2-12Supply Guide Upper Opening Lower Opening 2-13Chapter 2. Loading Supplies TC9490OH Rev. C 3/97 9490 Operator’s Handbook2-14 Chapter Connecting the Communications CablePrinting Establishing Communications9490 Operator’s Handbook Removing the Communications CableChapter 3. Printing Printing in On-Demand ModeCommunication Values 9490 Operator’s Handbook Printing in Continuous ModeInterrupting a Print Job TC9490OH Rev. C 3/97 Chapter 4. Care and MaintenanceThis chapter tells you how to clear label jams clean the battery contacts9490 Operator’s Handbook Clearing Label JamsCorrect Print CleaningChapter 4. Care and Maintenance Voids9490 Operator’s Handbook Cleaning the Battery ContactsTC9490OH Rev. C 3/97 Chapter 4. Care and Maintenance4. Reload the battery Battery Contacts EraserTC9490OH Rev. C 3/97 9490 Operator’s HandbookChapter TroubleshootingPrinting a Test Label 9490 Operator’s Handbook LED IndicatorSolution Problems and SolutionsChapter 5. Troubleshooting ProblemAddressing a Monarch 9490 Printer ProblemSolution 9490 Operator’s HandbookChapter Using the BootPutting the Boot on the Printer 9490 Operator’s Handbook 4. With Shoulder Strap Only. For both sides of the printer, put together the knob assembly and screw it into the threaded insert. Do not over-tighten the assemblyChapter 6. Using the Boot Taking the Boot off the PrinterTC9490OH Rev. C 3/97 9490 Operator’s HandbookAttaching the Cable Cover Chapter 7. Using the Cable Cover9490 Operator’s Handbook Removing the Cable CoverChapter SpecificationsSpecifications 9490 Operator’s Handbook Accessories and OptionsSupply Sizes Direction Chapter 8. SpecificationsCable Pin Outs DescriptionTC9490OH Rev. C 3/97 9490 Operator’s HandbookOn-demand mode GlossaryContinuous mode non-peel modeDirect communication between a computer Administratorerrors, and run diagnostics onlinePrinted in the U.S.A For supplies, service, or assistance callTOLL FREE Published by the Technical Communications Department