Manuals / Paxar / Computer Equipment / Printer

Paxar 4 manual Taking the Boot off the Printer, Using the Boot

Models: 4

1 54

Download 54 pages 11.95 Kb

Page 44

Image 44

Chapter 6. Using the Boot

Taking the Boot off the Printer ––––––––––––––––––––––––––––––––

To take the boot off the printer:

1.Industrial Version Only. Remove the cable from the side of the printer. Save the spacers and longer screws for when you want to use the printer with the boot.

2.With Shoulder Strap Only. Unscrew the knob assemblies on both sides of the printer (including the shoulder strap, if used), and take them off.

3.Pull on the boot and remove it from around the printer.

4.For both sides of the printer (at the top), put the screw assemblies together (including either shoulder strap, if preferred), put them into the threaded inserts and screw them in.

n Do not over-tighten the assembly.

5.Industrial Version Only. Reattach the cable using the shorter screws without the spacers.

TC9490OH Rev. C 3/97

6-3

Page 44

Image 44

Paxar 4 manual Taking the Boot off the Printer, Using the Boot

Contents

Operator’s Handbook Monarch Renegade 4 PrinterTC9490OH Rev. CB 3/01 1995 Monarch Marking Systems, Inc. All rights reservedCANADIAN D.O.C. WARNING TrademarksPage Table of Contents 9490 Operator’s Handbook Additional Optional Manuals ChapterGetting Started 9490 Operator’s Handbook Charging the BatteryAudience Chapter 1. Getting Started To charge the battery 9490 Operator’s HandbookLatch Tab Finger Depression Loading and Removing the BatteryChapter 1. Getting Started Connecting the AC Power Supply 9490 Operator’s HandbookConnecting the Shoulder Strap Chapter 1. Getting StartedUsing the Trigger and LED 9490 Operator’s HandbookChapter Loading SuppliesOpening the Printer 3. Tip the printhead assembly up and over the platen roller as shown Printhead Assembly Platen Roller Pinch Rollers Peel Bar9490 Operator’s Handbook 2. Pull the supply guide forward and down as shownChapter 2. Loading Supplies Printhead Assembly4. Slide the latches on the back of the printer toward the center LatchesLoading Ribbon 9490 Operator’s HandbookReloading a Ribbon Cassette Chapter 2. Loading Supplies9490 Operator’s Handbook n Do Not wrinkle or crush the ribbonChapter 2. Loading Supplies Loading for Peel ModeLoading Supplies TC9490OH Rev. C 3/97 9490 Operator’s HandbookSupply Holder Arrow Width of Supply Tabs Chapter 2. Loading Supplies n Make sure the labels turn freely in the supply wellSupply Holder TC9490OH Rev. C 3/979490 Operator’s Handbook 5. Close the printer and turn the printer onChapter 2. Loading Supplies Loading for Non-Peel Mode2-11 9490 Operator’s Handbook n Make sure the supplies turn freely in the supply well2-12 Supply HolderSupply Guide Upper Opening Lower Opening 2-13Chapter 2. Loading Supplies TC9490OH Rev. C 3/97 9490 Operator’s Handbook2-14 Connecting the Communications Cable PrintingEstablishing Communications ChapterRemoving the Communications Cable 9490 Operator’s HandbookChapter 3. Printing Printing in On-Demand ModeCommunication Values 9490 Operator’s Handbook Printing in Continuous ModeInterrupting a Print Job Chapter 4. Care and Maintenance This chapter tells you how to clear label jamsclean the battery contacts TC9490OH Rev. C 3/97Clearing Label Jams 9490 Operator’s HandbookCleaning Chapter 4. Care and MaintenanceVoids Correct PrintCleaning the Battery Contacts 9490 Operator’s HandbookChapter 4. Care and Maintenance 4. Reload the batteryBattery Contacts Eraser TC9490OH Rev. C 3/979490 Operator’s Handbook TC9490OH Rev. C 3/97Chapter TroubleshootingPrinting a Test Label LED Indicator 9490 Operator’s HandbookProblems and Solutions Chapter 5. TroubleshootingProblem SolutionProblem Solution9490 Operator’s Handbook Addressing a Monarch 9490 PrinterChapter Using the BootPutting the Boot on the Printer 4. With Shoulder Strap Only. For both sides of the printer, put together the knob assembly and screw it into the threaded insert. Do not over-tighten the assembly 9490 Operator’s HandbookTaking the Boot off the Printer Chapter 6. Using the Boot9490 Operator’s Handbook TC9490OH Rev. C 3/97Chapter 7. Using the Cable Cover Attaching the Cable CoverRemoving the Cable Cover 9490 Operator’s HandbookChapter SpecificationsSpecifications 9490 Operator’s Handbook Accessories and OptionsSupply Sizes Chapter 8. Specifications Cable Pin OutsDescription Direction9490 Operator’s Handbook TC9490OH Rev. C 3/97Glossary Continuous modenon-peel mode On-demand modeAdministrator errors, and run diagnosticsonline Direct communication between a computerFor supplies, service, or assistance call TOLL FREEPublished by the Technical Communications Department Printed in the U.S.A