Manuals / Paxar / Computer Equipment / Printer

Paxar 4 manual Removing the Communications Cable, Operator’s Handbook

Models: 4

1 54

Page 29

9490 Operator’s Handbook

2.Insert the connector into the printer port until the connector locks into place. You may hear a click as the cable’s latch snaps into place.

3.Gently pull on the cable holder to make sure it is secure.

4.Plug the other end of the cable into the port on your host.

Removing the Communications Cable

Please follow these instructions carefully. The cable could be damaged if removed incorrectly. To remove the cable from the printer:

1.Hold the printer steady with one hand.

2.Grasp the cable holder with your other hand and push it in to unlock the cable’s latch.

Release

Slide

Cable

Holder

3.Release the cable holder and grasp the release slide.

4.Gently pull the release slide to remove the cable.

n Do Not yank the cable from the printer.

3-2	TC9490OH Rev. C 3/97

Page 29

Image 29

Paxar 4 manual Removing the Communications Cable, Operator’s Handbook

Contents

Monarch Renegade 4 Printer Operator’s HandbookTC9490OH Rev. CB 3/01 1995 Monarch Marking Systems, Inc. All rights reservedTrademarks CANADIAN D.O.C. WARNINGPage Table of Contents 9490 Operator’s Handbook Additional Optional Manuals ChapterGetting Started 9490 Operator’s Handbook Charging the BatteryAudience Chapter 1. Getting Started 9490 Operator’s Handbook To charge the batteryLatch Tab Finger Depression Loading and Removing the BatteryChapter 1. Getting Started 9490 Operator’s Handbook Connecting the AC Power SupplyChapter 1. Getting Started Connecting the Shoulder Strap9490 Operator’s Handbook Using the Trigger and LEDChapter Loading SuppliesOpening the Printer Printhead Assembly Platen Roller Pinch Rollers Peel Bar 3. Tip the printhead assembly up and over the platen roller as shown9490 Operator’s Handbook 2. Pull the supply guide forward and down as shownPrinthead Assembly Chapter 2. Loading Supplies4. Slide the latches on the back of the printer toward the center Latches9490 Operator’s Handbook Loading RibbonChapter 2. Loading Supplies Reloading a Ribbon Cassetten Do Not wrinkle or crush the ribbon 9490 Operator’s HandbookChapter 2. Loading Supplies Loading for Peel ModeLoading Supplies TC9490OH Rev. C 3/97 9490 Operator’s HandbookSupply Holder Arrow Width of Supply Tabs n Make sure the labels turn freely in the supply well Chapter 2. Loading SuppliesSupply Holder TC9490OH Rev. C 3/975. Close the printer and turn the printer on 9490 Operator’s HandbookChapter 2. Loading Supplies Loading for Non-Peel Mode2-11 n Make sure the supplies turn freely in the supply well 9490 Operator’s Handbook2-12 Supply HolderSupply Guide Upper Opening Lower Opening 2-13Chapter 2. Loading Supplies TC9490OH Rev. C 3/97 9490 Operator’s Handbook2-14 Printing Connecting the Communications CableEstablishing Communications Chapter9490 Operator’s Handbook Removing the Communications CableChapter 3. Printing Printing in On-Demand ModeCommunication Values 9490 Operator’s Handbook Printing in Continuous ModeInterrupting a Print Job This chapter tells you how to clear label jams Chapter 4. Care and Maintenanceclean the battery contacts TC9490OH Rev. C 3/979490 Operator’s Handbook Clearing Label JamsChapter 4. Care and Maintenance CleaningVoids Correct Print9490 Operator’s Handbook Cleaning the Battery Contacts4. Reload the battery Chapter 4. Care and MaintenanceBattery Contacts Eraser TC9490OH Rev. C 3/97TC9490OH Rev. C 3/97 9490 Operator’s HandbookChapter TroubleshootingPrinting a Test Label 9490 Operator’s Handbook LED IndicatorChapter 5. Troubleshooting Problems and SolutionsProblem SolutionSolution Problem9490 Operator’s Handbook Addressing a Monarch 9490 PrinterChapter Using the BootPutting the Boot on the Printer 9490 Operator’s Handbook 4. With Shoulder Strap Only. For both sides of the printer, put together the knob assembly and screw it into the threaded insert. Do not over-tighten the assemblyChapter 6. Using the Boot Taking the Boot off the PrinterTC9490OH Rev. C 3/97 9490 Operator’s HandbookAttaching the Cable Cover Chapter 7. Using the Cable Cover9490 Operator’s Handbook Removing the Cable CoverChapter SpecificationsSpecifications 9490 Operator’s Handbook Accessories and OptionsSupply Sizes Cable Pin Outs Chapter 8. SpecificationsDescription DirectionTC9490OH Rev. C 3/97 9490 Operator’s HandbookContinuous mode Glossarynon-peel mode On-demand modeerrors, and run diagnostics Administratoronline Direct communication between a computerTOLL FREE For supplies, service, or assistance callPublished by the Technical Communications Department Printed in the U.S.A