Rear panel features | Peavey X-VCA manual

mono input module 2

rear panel features

direct out 1/4"TRS jack

The input channel's signal is available at this output jack.The default sig- nal routing is derived post-fader, post-eq and post-mute.This output jack is ground-compensated.

insert points

Separate 1/4" TRS jacks provide the facilities for inserting an external signal processor into the signal path of the input channel.

insert send

This jack serves as an output for connection to the input of a signal processor.The signal is derived after the mic preamp and HPF but before the eq section. Plugging a 1/4" TRS plug into this jack does not break the signal flow of the channel.This output jack is ground-compensated.

insert return

The output of a signal processor is fed to this jack. It can accept a bal- anced or unbalanced signal and is located pre-eq. Plugging a 1/4" TRS plug into this jack breaks the signal flow of the channel.

balanced line-in jack—Bal Line In

Line-level signals, balanced or unbalanced, may be brought into the input channel through this jack.The LINE switch must be depressed for this jack to be active.

balanced mic-in xlr connector—Bal Mic In

This balanced female XLR accepts a low-impedance microphone signal, or a line-level signal, depending on position of the LINE switch on the front panel.

see—mono input module, phantom power, line

p. 25

Image 25

Peavey X-VCA owner manual Rear panel features

Contents

VCA mixing consoles VCA Mono Input VCA block diagram Table of contents Page Format How to use this manualConventions Control Icons 1mono input module Module Block diagramPanel Mono input module Features 1mono input module Gain Module Aux PRE switches 1-2 Aux send featuresAux 5-6 & 7-8 PRE switch Aux sends 1-2 VCA Module EQ features 48TO24FITTED HPF-variable control High-pass filter-HPF BAL Insert RTN Insert Send Direct OUT Insert features PRE-SOURC Peak indicator-PK Level meter featuresSignal present indicator-SIG Level meter VCA Stereo Input Normally Fitted Bus assignment features Module Block diagram See Solo /VCA Edit switch section Solo switchInput fader Block diagram Module rear Rear panel features + Gain 2stereo input module Line select Line 2 switch Input signal switchingLeft and right mono-switches Stereo input module + Gain Input gain-GAIN + Gain AUX Aux sends 1-2, 3-4, 5-6 Aux 1/2, 3/4 and 5-8 PRE switches 150 HPF-High pass filter High-pass filter-HPF Stereo Input Left and Right signal LED indicators Metering featuresPeak indicator PK Balance control 2stereo input module Solo Balance on-groups-BAL on SIG See Solo Features section Line Bal Line Line-input left and right RCA connectors Balanced left and right line-in XLR connectorsLine-input left and right 1/4TRS jacks VCA Masters 1 of 8 Shown 3group module Group module Group module features Shown Module Block diagram Panel Matrix 1-4 levels-M1, M2, M3, M4 Matrix sendsPost-group VCA Masters Group dynamics section Group BUS PAN Comp Perc on Switch CompVOX on SwitchComp Auto on bothVOX and Perc switches depressed Gate on downward expander Output Audio group control features VCA VCA group master control features AUX Lamp dim Meter bridge connector Master Groups Stereo inputs Group insert point Group outputGroup insert send Group insert return Panel 4left / right & mono masters Matrix output control Left / right & mono master modulesMatrix master output level Talk to EXT Matrix sends Ster Module Output EQ features Matrix Balout Left / right & mono masters Output limiter on switch Output limiter featuresOutput limiter threshold control Gain reduction metering To Solo Block diagram Panel Sum L/R switch Left / Right module Output featuresTo Mono switch Mono module Talk to L/R switch Left / Right module 4left / right & mono masters Edit channel vca assign switch Vca assign switchMono solo switches 100mm Left, Right and Mono faders Matrix Level 5master control section Master control section Block diagram Panel Matrix sends Matrix 1 in to all 4 switchMono matrix 1-4 sends Matrix sends post mono 4 Shown External stereo program input VCA MA Alternate output features Lower Area Monitor out Solo off switchMonitor output level control Control Talkback and solo features 128 Post fader switch Solo featuresAdditive / last press pressed switch Solo active / clear switch Midi Out Matrix output connectors 1 through Matrix expansion connectorMatrix external input connectors 1 through Matrix expansion VCA Master Module Stereo Program In jacks left and right Left, Right and Mono insert pointsLeft, Right and Mono master outputs Monitor outputs left and right Microprocessor control 128 Microprocessor controlled muting Mute control panel Typical input or output Mute controller Microprocessor control IRecall Next Microprocessor control Channel mute controls KMute SwitchJStatus LED LMute LED Microprocessor control Creating a Mute Scene or Editing an existing one Mute scenes Microprocessor control Copying a Mute Scene Copying a mute scene Microprocessor control Safe Scene Microprocessor control Utilities Display Meaning Settings Microprocessor control Changing and reviewing the utility changes Utility Mode Inputs and outputs Micro control panel Vca facilities VCA operation overview Vca facilities Method 1- Channel to Master Assignment VCA assigning overviewMethod 2- Master to Channel Assignment Vca facilities VCA Assignment- Scene-to-Scene changes Vca facilities This first method assigns Channels to Masters VCA assignment 1 detailed operation Vca facilities VCA Safe Mode Vca facilities VCA Assignment- Masters to Channels VCA assignment 2 Detailed Operation Vca facilities VCA copy Vca facilities VCA Assignment starting fresh Vca facilities VCA Mute switch Vca facilities VCA Master Solo/Assign switch Vca facilities Solo operation of a Channel assigned to multipleVCA Groups VCA channel soloChannel initially un-solo’d, then 1VCA Group solo’d Solo VCA edit switch Solo Functions Solo VCA edit switchVCA Channel Assignment Function Dynamics control Introduction VCA dynamics control Dynamics control Group section Compressor/Limiter functions To set up the compressor/limiter function Dynamics control Group section gate functions To set up the gate function Dynamics control Output limiter functions Model 5A power supply Power supply Power supply usage Power supply0Console and power supply grounding Redundant power supplies DC out receptacle DC out cable Model 5A power supply Specifications Supply identification Power requirementsGround linking Twin-supply operation 01/25/01