Master control section, Matrix output control | Peavey X-VCA

master control section 5

features

The Master control section offers some flexible signal routing solutions as well as utilitarian functions.Also included is the Microprocessor section, which is described separately in it's own chapter.The master control section includes the following features:

*Matrix Output Control

*Matrix Send 1 though 4

*External stereo program input with EQ

*Talkback input and control

*Alternate output and Monitor output control

*Headphone and solo control features

Matrix output control

The the master control section contains Matrix Masters 3 and 4.

mute

Mute switch

See LOCAL MICROPROCESSOR CONTROL section

Matrix master output level

The MATRIX MASTER output level controls set the levels that appear at the corresponding MATRIX output connectors on the rear-panel.

Talk to

Adds the TALKBACK system output to the associated MATRIX output.The level of the TALKBACK signal is set by the TALKBACK level control in the MAS- TER section.

solo switch

Pressing this momentary switch will include (illuminate) or exclude (not-illu- minated) the channel from the consoles solo system.

See SOLO FEATURES section.

write-in label

This label may be written on with a grease-marker, or dry-erase pen and later wiped clean. Masking tape may also be placed on this surface, if desired. If you write on it with a "Sharpie", you may have trouble getting the writing off. If this is the case, your best bet is to wipe the label off with isopropyl (rubbing) alcohol.

p. 71

Image 71

Peavey X-VCA owner manual Master control section, Matrix output control

Contents

VCA mixing consoles VCA Mono Input VCA block diagram Table of contents Page Control Icons How to use this manualFormat Conventions Panel Module Block diagram1mono input module Mono input module Features 1mono input module Gain Module Aux sends 1-2 Aux send featuresAux PRE switches 1-2 Aux 5-6 & 7-8 PRE switch VCA Module EQ features 48TO24FITTED HPF-variable control High-pass filter-HPF BAL Insert RTN Insert Send Direct OUT Insert features PRE-SOURC Level meter Level meter featuresPeak indicator-PK Signal present indicator-SIG VCA Stereo Input Normally Fitted Bus assignment features Module Block diagram Input fader Solo switchSee Solo /VCA Edit switch section Block diagram Module rear Rear panel features + Gain 2stereo input module Stereo input module Input signal switchingLine select Line 2 switch Left and right mono-switches + Gain Input gain-GAIN + Gain AUX Aux sends 1-2, 3-4, 5-6 Aux 1/2, 3/4 and 5-8 PRE switches 150 HPF-High pass filter High-pass filter-HPF Stereo Input Balance control Metering featuresLeft and Right signal LED indicators Peak indicator PK 2stereo input module Solo Balance on-groups-BAL on SIG See Solo Features section Line Bal Line Line-input left and right 1/4TRS jacks Balanced left and right line-in XLR connectorsLine-input left and right RCA connectors VCA Masters 1 of 8 Shown 3group module Group module Group module features Shown Module Block diagram Panel Post-group Matrix sendsMatrix 1-4 levels-M1, M2, M3, M4 VCA Masters Group dynamics section Group BUS PAN Gate on downward expander CompVOX on SwitchComp Perc on Switch Comp Auto on bothVOX and Perc switches depressed Output Audio group control features VCA VCA group master control features AUX Lamp dim Meter bridge connector Master Groups Stereo inputs Group insert return Group outputGroup insert point Group insert send Panel 4left / right & mono masters Talk to Left / right & mono master modulesMatrix output control Matrix master output level EXT Matrix sends Ster Module Output EQ features Matrix Balout Left / right & mono masters Gain reduction metering Output limiter featuresOutput limiter on switch Output limiter threshold control To Solo Block diagram Panel Talk to L/R switch Left / Right module Output featuresSum L/R switch Left / Right module To Mono switch Mono module 4left / right & mono masters 100mm Left, Right and Mono faders Vca assign switchEdit channel vca assign switch Mono solo switches Matrix Level 5master control section Master control section Block diagram Panel Matrix sends post mono Matrix 1 in to all 4 switchMatrix sends Mono matrix 1-4 sends 4 Shown External stereo program input VCA MA Alternate output features Lower Area Monitor output level control Solo off switchMonitor out Control Talkback and solo features 128 Solo active / clear switch Solo featuresPost fader switch Additive / last press pressed switch Midi Out Matrix expansion Matrix expansion connectorMatrix output connectors 1 through Matrix external input connectors 1 through VCA Master Module Monitor outputs left and right Left, Right and Mono insert pointsStereo Program In jacks left and right Left, Right and Mono master outputs Microprocessor control 128 Microprocessor controlled muting Mute control panel Typical input or output Mute controller Microprocessor control IRecall Next Microprocessor control LMute LED KMute SwitchChannel mute controls JStatus LED Microprocessor control Creating a Mute Scene or Editing an existing one Mute scenes Microprocessor control Copying a Mute Scene Copying a mute scene Microprocessor control Safe Scene Microprocessor control Utilities Display Meaning Settings Microprocessor control Changing and reviewing the utility changes Utility Mode Inputs and outputs Micro control panel Vca facilities VCA operation overview Vca facilities Method 2- Master to Channel Assignment VCA assigning overviewMethod 1- Channel to Master Assignment Vca facilities VCA Assignment- Scene-to-Scene changes Vca facilities This first method assigns Channels to Masters VCA assignment 1 detailed operation Vca facilities VCA Safe Mode Vca facilities VCA Assignment- Masters to Channels VCA assignment 2 Detailed Operation Vca facilities VCA copy Vca facilities VCA Assignment starting fresh Vca facilities VCA Mute switch Vca facilities VCA Master Solo/Assign switch Vca facilities Channel initially un-solo’d, then 1VCA Group solo’d VCA channel soloSolo operation of a Channel assigned to multipleVCA Groups Solo VCA edit switch VCA Channel Assignment Function Solo VCA edit switchSolo Functions Dynamics control Introduction VCA dynamics control Dynamics control Group section Compressor/Limiter functions To set up the compressor/limiter function Dynamics control Group section gate functions To set up the gate function Dynamics control Output limiter functions Model 5A power supply Power supply Redundant power supplies Power supply0Power supply usage Console and power supply grounding DC out receptacle DC out cable Model 5A power supply Specifications Twin-supply operation Power requirementsSupply identification Ground linking 01/25/01