System Information, DIP Switch Information | Pelco C3412M-D manual

System Information

SPECTRA IV

LANGUAGE

<SYSTEM INFORMATION> <DISPLAY SETUP> <DOME SETTINGS>

ACK ALERT*

RESET CAMERA

CYCLE CAMERA POWER REBOOT SYSTEM

EXIT

SYSTEM INFORMATION

SERIAL #

DOME DRIVE MODEL

BACK BOX MEMORY

SOFTWARE VERSION

BUILD

FONT VERSION

COMM

DADDRESS P ADDRESS CM9500 MODE 32 PRESETS PROTOCOL PRESSURIZED* <ADDITIONAL>

BACK

EXIT

ADDITIONAL

FREE MEMORY LAST RESET AZIMUTH ZERO OFFSET MOTOR ACTIVE CAMERA ACTIVE VIDEO LEVEL CAMERA MODEL LANGUAGE 1 LANGUAGE 2 LANGUAGE 3 LANGUAGE 4 LANGUAGE 5 LANGUAGE 6 LANGUAGE 7 LANGUAGE 8 LANGUAGE 9 LANGUAGE 10 <DIPSWITCH INFORMATION>

BACK

EXIT

The System Information menu displays the dome drive model, software version, available memory, DIP switch information, and other diagnostic information.

System settings cannot be changed using this menu; this information is for reference only.

Use the following steps to display the System Information menu:

1.Use the joystick to position the cursor beside SYSTEM INFORMATION.

2.Press Iris Open. The SYSTEM INFORMATION menu opens.

DIP SWITCH INFORMATION

The DIP Switch Information menu displays the dome drive’s current DIP switch settings. This provides a way to remotely view the DIP switch settings without removing the dome drive from the back box.

DIP SWITCH INFORMATION
1 2 3 4 5 6 7 8		1 2 3 4 5 6 7 8 9 0	]
SW1[- - - - - - - -	]	SW2[- - - - - - - - - -

SW1 1-8 :

D ADDRESS 1

P ADDRESS 1

SW2 1 : 32 PRESETS. OFF

SW2 2 : CM9500 MODE. OFF

SW2 3 : COAX SPIV

SW2 4-5 : RS422 <->

SW2 6-8 : COMM. 2400.N.8.1

SW2 9 : UTC SOURCE. COAX

SW2 10 : TX/RX TERM.. OFF

PRESS IRIS OPEN TO CONTINUE

* This setting applies only to Pressurized Spectra IV dome systems.

C3412M-D (12/08)

35

Image 35

Pelco C3412M-D manual System Information, DIP Switch Information, Address SW2 1 32 PRESETS. OFF, SW2 3 Coax Spiv

Contents

Spectra IV and Spectra IV SE Series Page Contents Field Align Wide Dynamic Range Repeat Ack Action Activate Aux Current Reading Reset Alert Welcome SW2 Switch 2 CM9502 Setting InstallationSwitch Settings SW2 Switch 1 AD-32 Preset System SW2 Switches 4-5 Serial Port Settings SW2 Switch 3 Control System Compatibility SW2 Switches 6-8 Baud Settings Dome Drive Installation Table A. Switch Settings for SW1 P-Type Control OFF Table B. Switch Settings for SW1 D-Type Control Table B. Switch Settings for SW1 D-Type Control 100 106 141 176 211 246 Getting Started Operation How to Operate Your Dome System Quick Programming Guide Accessing Main Menu Preset CM9500 VCD5000 Endura Workstation 16X LowLight Color Menu Tree AUX Dome SettingsLine Sync Presets Edit the Password Clock Event 18X LowLight Day/Night Menu Tree Title Text Line Sync Presets PatternsAlarms AUX Edit the Password Clock 22X EXview LowLight Color Menu Tree Line Sync Alarms Alarm Settings 23X LowLight Day/Night Menu Tree Edit Detection Areas Patterns 35X LowLight Day/Night Menu Tree Edit Detection Areas Exit ACK Alert Reset CameraLanguage Spectra Language System Information DIP Switch InformationDIP Switch Information Address SW2 1 32 PRESETS. OFF Restore Factory Defaults Back Exit Display SetupExit Display Setup Preset Label XXX.XX Title Text Save and Exit Cancel and Exit Help Type of Lighting Dome SettingsExit Dome Settings Camera Camera Back Exit Camera Advanced Settings Back ExitZoom Limit LOW Light Limit Zoom Speed Applies only to 18X, 23X, and 35X models IR CUT Filter AGC Limit Advanced Camera SettingsShutter Speed Back Exit Auto IrisAuto White Balance Gain B Gain Auto White Balance Auto Sharpness Auto Iris Level Auto Iris Peak Dome Settings ACK Alert Reset CameraBacklight Compensation BLC Video Level Field Align Sensor Scan Mode Electronic Image Stabilization LOW LUX Noise Reduction Image Enhancement Applies only to 23X and 35X models Wide Dynamic Range Proportional PAN Auto Flip Back Exit Motion Exit Dome Settings Camera Motion Power UPPark Time Scan Speed Preset Freeze Frame Limit Stops Azimuth Zero Back Exit Power UP Power UP Action Power UPPower UP Action Line Sync Back Exit Line Sync Line Sync Phase Model Number of Stored Presets Presets Abcdefghij Cancel Klmnopqrst Uvwxyz Space Back Exit Presets Preset NumberLabel for Preset Preset Number C3412M-D 12/08 Edit Detection Areas Enable Motion DetectionPresets Preset Number Preset not Defined Edit Schedule Clear Preset Clear Camera Settings Back Exit Motion Detection Areas Edit Schedule Activate AUX CommandAUX Time Back Exit Patterns PatternsPatterns Zones Zones SET Windows Back Exit Window BlankingBack Exit Window Blanking Style Clear Window Enable Window Reverse Clear Window Back ExitReverse Window Blank Tilt Angles Blank ALL ABOVE/BLANK ALL below Alarms C3412M-D 12/08 Default Normally open Dwell Time Secs Edit Schedule Back Exit Back Exit AUX AUX 1 Mode Toggle Dwell Time Secs AUX 2 ModeAUX Edit Title Text Title TextBack Exit Title Text Repeat Alert Current Reading Reset AlertACK Action Activate AUX Clear Back Exit Edit the Password PasswordBack Exit Password Clock END Date Month October DAY END Time Clock Time Base Internal ClockHour Month April DAY END Date Month October Week Last DAY Sunday END Time Time Base Internal ClockMM/DD/YYYY Month April Week 1ST DAY Sunday Event Back Exit Reference Information Event TypeBack Exit Event Event Type Event Label Holiday Edit Event Label Event Label Edit Event Event Label Event Active Event Time Event Type Preset Number Back ExitEdit Event Back Exit Event Event Type Event Label Edit Event Label Holiday Clear EventList Event Month January DAY Back Exit Edit HolidayEdit Holiday Occurrence List Holidays Clear Holiday Event Number Event Type Label Time Occurs Holiday Scheduled Events Reboot System Reset, Cycle Power, RebootReset Camera Cycle Camera Power Software/Language File Upload Suggested Preventative Maintenance 16X Models Specifications DD4CBW18 18X Models DD4C22 22X Models DD4CBW23 23X Models DD4CBW23-X DD4CBW35 35X Models DD4CBW35-X Page Product Warranty and Return Information