Reset, Cycle Power, Reboot, Reset Camera | Pelco C3412M-D specs

Reset, Cycle Power, Reboot

SPECTRA IV

LANGUAGEENGLISH

<SYSTEM INFORMATION> <DISPLAY SETUP> <DOME SETTINGS>

ACK ALERT*

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

EXIT

RESET CAMERA

Use this function to reset all camera settings to factory default parameters.

CYCLE CAMERA POWER

If the camera is not operating or if you lose camera control, cycle camera power. Cycling camera power resets the camera but does not change any saved camera settings.

REBOOT SYSTEM

Reboot the system if it is not operating or if there is no control. Rebooting the system will cycle dome and camera power without changing programmed dome settings.

88	C3412M-D (12/08)

Image 88

Pelco C3412M-D manual Reset, Cycle Power, Reboot, Reset Camera, Cycle Camera Power, Reboot System, Spectra Languageenglish

Contents

Spectra IV and Spectra IV SE Series Page Contents Wide Dynamic Range Field Align Repeat Ack Action Activate Aux Current Reading Reset Alert Welcome Installation Switch SettingsSW2 Switch 1 AD-32 Preset System SW2 Switch 2 CM9502 Setting SW2 Switch 3 Control System Compatibility SW2 Switches 4-5 Serial Port Settings Dome Drive Installation SW2 Switches 6-8 Baud Settings Table A. Switch Settings for SW1 P-Type Control Table B. Switch Settings for SW1 D-Type Control OFF Table B. Switch Settings for SW1 D-Type Control 100 106 141 176 211 246 Getting Started How to Operate Your Dome System Operation Accessing Main Menu Preset Quick Programming Guide CM9500 Endura Workstation VCD5000 16X LowLight Color Menu Tree Dome Settings Line Sync PresetsEdit the Password Clock Event AUX 18X LowLight Day/Night Menu Tree Line Sync Presets Patterns Alarms AUXEdit the Password Clock Title Text 22X EXview LowLight Color Menu Tree Alarms Alarm Settings Line Sync 23X LowLight Day/Night Menu Tree Edit Detection Areas Patterns 35X LowLight Day/Night Menu Tree Edit Detection Areas ACK Alert Reset Camera LanguageSpectra Language Exit DIP Switch Information DIP Switch InformationAddress SW2 1 32 PRESETS. OFF System Information Exit Display Setup Preset Label Display SetupRestore Factory Defaults Back Exit Title Text Save and Exit Cancel and Exit Help XXX.XX Dome Settings Exit Dome Settings CameraCamera Type of Lighting Zoom Limit Advanced Settings Back ExitBack Exit Camera Zoom Speed LOW Light Limit IR CUT Filter Applies only to 18X, 23X, and 35X models Shutter Speed Advanced Camera SettingsAGC Limit Auto White Balance Gain B Gain Auto IrisBack Exit Auto Sharpness Auto White Balance Dome Settings ACK Alert Reset Camera Backlight Compensation BLCVideo Level Auto Iris Level Auto Iris Peak Sensor Scan Mode Field Align Electronic Image Stabilization Image Enhancement LOW LUX Noise Reduction Wide Dynamic Range Applies only to 23X and 35X models Auto Flip Proportional PAN Park Time Exit Dome Settings Camera Motion Power UPBack Exit Motion Preset Freeze Frame Scan Speed Limit Stops Azimuth Zero Power UP Action Power UPBack Exit Power UP Power UP Action Back Exit Line Sync Line Sync Phase Line Sync Presets Model Number of Stored Presets Label for Preset Preset Number Back Exit Presets Preset NumberAbcdefghij Cancel Klmnopqrst Uvwxyz Space C3412M-D 12/08 Enable Motion Detection Presets Preset Number Preset not DefinedEdit Schedule Clear Preset Clear Camera Settings Back Exit Edit Detection Areas Motion Detection Areas AUX Time Activate AUX CommandEdit Schedule Patterns Zones PatternsBack Exit Patterns Zones Window Blanking Back Exit Window BlankingStyle SET Windows Back Exit Reverse Enable Window Reverse Clear Window Back ExitClear Window Blank ALL ABOVE/BLANK ALL below Window Blank Tilt Angles Alarms C3412M-D 12/08 Default Normally open AUX Back Exit AUX AUX 1 Mode Toggle Dwell Time Secs AUX 2 ModeDwell Time Secs Edit Schedule Back Exit Back Exit Title Text Title TextEdit Title Text Alert Repeat Reset Alert ACK ActionActivate AUX Current Reading Clear Back Exit Password PasswordBack Exit Edit the Password Clock Clock Time Base Internal Clock HourMonth April DAY END Date Month October DAY END Time Time Base Internal Clock MM/DD/YYYYMonth April Week 1ST DAY Sunday END Date Month October Week Last DAY Sunday END Time Event Event Type Back Exit Event Event Type Event LabelHoliday Back Exit Reference Information Event Label Edit Event Label Event Type Preset Number Back Exit Edit EventBack Exit Event Event Type Event Label Edit Event Label Edit Event Event Label Event Active Event Time List Event Clear EventHoliday Edit Holiday Occurrence Edit HolidayMonth January DAY Back Exit Clear Holiday List Holidays Scheduled Events Event Number Event Type Label Time Occurs Holiday Reset, Cycle Power, Reboot Reset CameraCycle Camera Power Reboot System Software/Language File Upload Suggested Preventative Maintenance Specifications 16X Models 18X Models DD4CBW18 22X Models DD4C22 23X Models DD4CBW23 DD4CBW23-X 35X Models DD4CBW35 DD4CBW35-X Page Product Warranty and Return Information