Manuals / Pelco / Photography / Security Camera

Pelco C3412M-D manual Clear Event, List Event, Holiday

Models: C3412M-D

1 100

Download 100 pages 17.63 Kb

Page 84

SPECTRA IV

LANGUAGE

<SYSTEM INFORMATION> <DISPLAY SETUP> <DOME SETTINGS>

ACK ALERT*

RESET CAMERA

CYCLE CAMERA POWER REBOOT SYSTEM

EXIT

DOME SETTINGS

<CAMERA>

<MOTION> <POWER UP> <LINE SYNC> <PRESETS> <PATTERNS> <ZONES>

<WINDOW BLANKING> <ALARMS>

<AUX>

<TITLE TEXT> <ALERT>* <CLEAR> <PASSWORD> <CLOCK> <EVENT>

BACK

EXIT

EVENT

EVENT TYPE

EVENT LABEL

<EDIT EVENT LABEL> <EDIT EVENT> <CLEAR EVENT> <LIST EVENT>

HOLIDAY

<EDIT HOLIDAY> <CLEAR HOLIDAY> <LIST HOLIDAYS>

BACK

EXIT

REFERENCE INFORMATION

CLEAR EVENT

To clear an event:

1.Use the joystick to position the cursor beside CLEAR EVENT.

2.Press Iris Open.

3.Follow the directions displayed on the monitor.

LIST EVENT

To list events:

1.Use the joystick to position the cursor beside LIST EVENT.

2.Press Iris Open.

3.All programmed events will be listed.

HOLIDAY

Use the following steps to create a new holiday.

1.Use the joystick to position the cursor beside HOLIDAY. Press Iris Open.

2.Move the joystick up or down to scroll through the options. If no holidays were created in the past, NEW is the only selectable option. Press Iris Open to select NEW.

3.Proceed to Edit Holiday on page 85.

Use the following steps to manage an existing holiday.

1.Use the joystick to position the cursor beside HOLIDAY. Press Iris Open.

2.Move the joystick up or down to scroll through the holidays. Press Iris Open to enter a selection.

3.Proceed to Edit Holiday on page 85.

Note: Holidays cannot be changed through the Edit Schedule option from the Preset, Pattern, Window Blanking, Alarm, or Aux menus.

* This setting applies only to Pressurized Spectra IV dome systems.

84	C3412M-D (12/08)

Image 84

Pelco C3412M-D manual Clear Event, List Event, Holiday

Contents

Spectra IV and Spectra IV SE Series Page Contents Wide Dynamic Range Field AlignRepeat Ack Action Activate Aux Current Reading Reset Alert Welcome Installation Switch SettingsSW2 Switch 1 AD-32 Preset System SW2 Switch 2 CM9502 SettingSW2 Switch 3 Control System Compatibility SW2 Switches 4-5 Serial Port SettingsDome Drive Installation SW2 Switches 6-8 Baud SettingsTable A. Switch Settings for SW1 P-Type Control Table B. Switch Settings for SW1 D-Type Control OFFTable B. Switch Settings for SW1 D-Type Control 100 106 141 176 211 246 Getting Started How to Operate Your Dome System OperationAccessing Main Menu Preset Quick Programming GuideCM9500 Endura Workstation VCD500016X LowLight Color Menu Tree Dome Settings Line Sync PresetsEdit the Password Clock Event AUX18X LowLight Day/Night Menu Tree Line Sync Presets Patterns Alarms AUXEdit the Password Clock Title Text22X EXview LowLight Color Menu Tree Alarms Alarm Settings Line Sync23X LowLight Day/Night Menu Tree Edit Detection Areas Patterns 35X LowLight Day/Night Menu Tree Edit Detection Areas ACK Alert Reset Camera LanguageSpectra Language ExitDIP Switch Information DIP Switch InformationAddress SW2 1 32 PRESETS. OFF System InformationDisplay Setup Exit Display Setup Preset LabelRestore Factory Defaults Back Exit Title Text Save and Exit Cancel and Exit Help XXX.XXDome Settings Exit Dome Settings CameraCamera Type of LightingAdvanced Settings Back Exit Zoom LimitBack Exit Camera Zoom Speed LOW Light LimitIR CUT Filter Applies only to 18X, 23X, and 35X modelsAdvanced Camera Settings Shutter SpeedAGC Limit Auto Iris Auto White Balance Gain B GainBack Exit Auto Sharpness Auto White BalanceDome Settings ACK Alert Reset Camera Backlight Compensation BLCVideo Level Auto Iris Level Auto Iris PeakSensor Scan Mode Field AlignElectronic Image Stabilization Image Enhancement LOW LUX Noise ReductionWide Dynamic Range Applies only to 23X and 35X modelsAuto Flip Proportional PANExit Dome Settings Camera Motion Power UP Park TimeBack Exit Motion Preset Freeze Frame Scan SpeedLimit Stops Azimuth Zero Power UP Power UP ActionBack Exit Power UP Power UP Action Back Exit Line Sync Line Sync Phase Line SyncPresets Model Number of Stored PresetsBack Exit Presets Preset Number Label for Preset Preset NumberAbcdefghij Cancel Klmnopqrst Uvwxyz Space C3412M-D 12/08 Enable Motion Detection Presets Preset Number Preset not DefinedEdit Schedule Clear Preset Clear Camera Settings Back Exit Edit Detection AreasMotion Detection Areas Activate AUX Command AUX TimeEdit Schedule Patterns Patterns ZonesBack Exit Patterns Zones Window Blanking Back Exit Window BlankingStyle SET Windows Back ExitEnable Window Reverse Clear Window Back Exit ReverseClear Window Blank ALL ABOVE/BLANK ALL below Window Blank Tilt AnglesAlarms C3412M-D 12/08 Default Normally open Back Exit AUX AUX 1 Mode Toggle Dwell Time Secs AUX 2 Mode AUXDwell Time Secs Edit Schedule Back Exit Title Text Back Exit Title TextEdit Title Text Alert RepeatReset Alert ACK ActionActivate AUX Current ReadingClear Password Back Exit PasswordBack Exit Edit the Password Clock Clock Time Base Internal Clock HourMonth April DAY END Date Month October DAY END TimeTime Base Internal Clock MM/DD/YYYYMonth April Week 1ST DAY Sunday END Date Month October Week Last DAY Sunday END TimeEvent Event Type Back Exit Event Event Type Event LabelHoliday Back Exit Reference InformationEvent Label Edit Event LabelEvent Type Preset Number Back Exit Edit EventBack Exit Event Event Type Event Label Edit Event Label Edit Event Event Label Event Active Event TimeClear Event List EventHoliday Edit Holiday Edit Holiday OccurrenceMonth January DAY Back Exit Clear Holiday List HolidaysScheduled Events Event Number Event Type Label Time Occurs HolidayReset, Cycle Power, Reboot Reset CameraCycle Camera Power Reboot SystemSoftware/Language File Upload Suggested Preventative Maintenance Specifications 16X Models18X Models DD4CBW1822X Models DD4C2223X Models DD4CBW23DD4CBW23-X 35X Models DD4CBW35DD4CBW35-X Page Product Warranty and Return Information