Title Text Save and Exit Cancel and Exit Help | Pelco C3412M-D

LABEL POSITIONS

SPECTRA IV

LANGUAGE

<SYSTEM INFORMATION> <DISPLAY SETUP> <DOME SETTINGS>

ACK ALERT*

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

EXIT

DISPLAY SETUP

PRESET LABEL

ZONE LABEL ZOOM AZIMUTH/ELEVATION DIRECTION ALARM MESSAGE DATE/TIME

EVENT LABEL <LABEL POSITIONS> RESTORE FACTORY DEFAULTS

BACK

EXIT

LABEL POSITION

[ZONE LABEL-------		]
[PRESET LABEL-------		]
[ALARM 1	-------]
[EVENT-------	]
[ALERT MESSAGE-------		]*
<TITLE TEXT>

SAVE AND EXIT

CANCEL AND EXIT

HELP

XXXo/-XXXo

NE

XXX.XX

XX/XX/YYYY 00:00

Labels can be placed anywhere on the monitor. This feature allows you to customize the appearance of your monitor screen.

The following labels are not set at fixed positions:

PRESET LABEL

ZONE LABEL

ALARM 1

ZOOM RATIO - XXX.XX

AZIMUTH1/ELEVATION2 - XXX°/-XX°

DIRECTION - NE

ALERT MESSAGE3*

TITLE TEXT

EVENT LABEL

To set a label position:

1.Use the joystick to position the cursor beside a label.

2.Press Iris Open.

3.Use the joystick to move the label up, down, left, or right.

4.Press Iris Open.

5.Repeat steps 1–4 to position other labels.

6.Position the cursor next to Save and Exit. Press Iris Open to save settings and exit the menu.

1Azimuth is the pan angle from zero to 359 degrees.

2Elevation is the tilt position from zero (horizon) to -90 degrees.

3The alert message is the warning displayed on the monitor if pressure, temperature, or dew point inside the dome reach unacceptable levels.

* This setting applies only to Pressurized Spectra IV dome systems.

C3412M-D (12/08)

37

Image 37

Pelco C3412M-D manual Title Text Save and Exit Cancel and Exit Help, Xxx.Xx

Contents

Spectra IV and Spectra IV SE Series Page Contents Field Align Wide Dynamic Range Repeat Ack Action Activate Aux Current Reading Reset Alert Welcome Switch Settings InstallationSW2 Switch 1 AD-32 Preset System SW2 Switch 2 CM9502 Setting SW2 Switches 4-5 Serial Port Settings SW2 Switch 3 Control System Compatibility SW2 Switches 6-8 Baud Settings Dome Drive Installation Table A. Switch Settings for SW1 P-Type Control OFF Table B. Switch Settings for SW1 D-Type Control Table B. Switch Settings for SW1 D-Type Control 100 106 141 176 211 246 Getting Started Operation How to Operate Your Dome System Quick Programming Guide Accessing Main Menu Preset CM9500 VCD5000 Endura Workstation 16X LowLight Color Menu Tree Line Sync Presets Dome SettingsEdit the Password Clock Event AUX 18X LowLight Day/Night Menu Tree Alarms AUX Line Sync Presets PatternsEdit the Password Clock Title Text 22X EXview LowLight Color Menu Tree Line Sync Alarms Alarm Settings 23X LowLight Day/Night Menu Tree Edit Detection Areas Patterns 35X LowLight Day/Night Menu Tree Edit Detection Areas Language ACK Alert Reset CameraSpectra Language Exit DIP Switch Information DIP Switch InformationAddress SW2 1 32 PRESETS. OFF System Information Exit Display Setup Preset Label Display SetupRestore Factory Defaults Back Exit XXX.XX Title Text Save and Exit Cancel and Exit Help Exit Dome Settings Camera Dome SettingsCamera Type of Lighting Zoom Limit Advanced Settings Back ExitBack Exit Camera LOW Light Limit Zoom Speed Applies only to 18X, 23X, and 35X models IR CUT Filter Shutter Speed Advanced Camera SettingsAGC Limit Auto White Balance Gain B Gain Auto IrisBack Exit Auto White Balance Auto Sharpness Backlight Compensation BLC Dome Settings ACK Alert Reset CameraVideo Level Auto Iris Level Auto Iris Peak Field Align Sensor Scan Mode Electronic Image Stabilization LOW LUX Noise Reduction Image Enhancement Applies only to 23X and 35X models Wide Dynamic Range Proportional PAN Auto Flip Park Time Exit Dome Settings Camera Motion Power UPBack Exit Motion Scan Speed Preset Freeze Frame Limit Stops Azimuth Zero Power UP Action Power UPBack Exit Power UP Power UP Action Line Sync Back Exit Line Sync Line Sync Phase Model Number of Stored Presets Presets Label for Preset Preset Number Back Exit Presets Preset NumberAbcdefghij Cancel Klmnopqrst Uvwxyz Space C3412M-D 12/08 Presets Preset Number Preset not Defined Enable Motion DetectionEdit Schedule Clear Preset Clear Camera Settings Back Exit Edit Detection Areas Motion Detection Areas AUX Time Activate AUX CommandEdit Schedule Patterns Zones PatternsBack Exit Patterns Zones Back Exit Window Blanking Window BlankingStyle SET Windows Back Exit Reverse Enable Window Reverse Clear Window Back ExitClear Window Window Blank Tilt Angles Blank ALL ABOVE/BLANK ALL below Alarms C3412M-D 12/08 Default Normally open AUX Back Exit AUX AUX 1 Mode Toggle Dwell Time Secs AUX 2 ModeDwell Time Secs Edit Schedule Back Exit Back Exit Title Text Title TextEdit Title Text Repeat Alert ACK Action Reset AlertActivate AUX Current Reading Clear Back Exit Password PasswordBack Exit Edit the Password Clock Hour Clock Time Base Internal ClockMonth April DAY END Date Month October DAY END Time MM/DD/YYYY Time Base Internal ClockMonth April Week 1ST DAY Sunday END Date Month October Week Last DAY Sunday END Time Event Back Exit Event Event Type Event Label Event TypeHoliday Back Exit Reference Information Edit Event Label Event Label Edit Event Event Type Preset Number Back ExitBack Exit Event Event Type Event Label Edit Event Label Edit Event Event Label Event Active Event Time List Event Clear EventHoliday Edit Holiday Occurrence Edit HolidayMonth January DAY Back Exit List Holidays Clear Holiday Event Number Event Type Label Time Occurs Holiday Scheduled Events Reset Camera Reset, Cycle Power, RebootCycle Camera Power Reboot System Software/Language File Upload Suggested Preventative Maintenance 16X Models Specifications DD4CBW18 18X Models DD4C22 22X Models DD4CBW23 23X Models DD4CBW23-X DD4CBW35 35X Models DD4CBW35-X Page Product Warranty and Return Information