Activate AUX Command, AUX Time, Edit Schedule | Pelco C3412M-D

SPECTRA IV

LANGUAGE

<SYSTEM INFORMATION> <DISPLAY SETUP> <DOME SETTINGS>

ACK ALERT*

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

EXIT

DOME SETTINGS

<CAMERA>

<MOTION> <POWER UP> <LINE SYNC> <PRESETS> <PATTERNS> <ZONES>

<WINDOW BLANKING> <ALARMS>

<AUX>

<TITLE TEXT> <ALERT>* <CLEAR> <PASSWORD> <CLOCK> <EVENT>

BACK

EXIT

PRESETS

PRESET NUMBER

* * * PRESET NOT DEFINED * * *

<EDIT PRESET LABEL> <EDIT PRESET SCENE> <EDIT CAMERA SETTINGS> <MOTION DETECTION>

<EDIT SCHEDULE>

<CLEAR PRESET>

<CLEAR CAMERA SETTINGS>

BACK

EXIT

REFERENCE INFORMATION AZIMUTH

ELEVATION

ZOOM RATIO

CUSTOM CAMERA SETTINGS

MOTION DETECTION

MOTION DETECTION ENABLED <EDIT DETECTION AREAS> ACTIVATE AUX

AUX TIME (SECS)

BACK

EXIT

ACTIVATE AUX COMMAND

(Applies only to 23X and 35X models.)

Motion detection can be programmed to trigger an auxiliary command when motion is detected. The following are the settings for ACTIVATE AUX:

OFF (default): Motion detection will not trigger an AUX command.

1:Triggers a command to AUX 1.

2:Triggers a command to AUX 2.

AUX TIME

(Applies only to 23X and 35X models.)

Aux time is the length of time the auxiliary will remain on after motion is detected. Available settings for AUX TIME are 1–60 seconds.

EDIT SCHEDULE

The Edit Schedule menu is a duplicate of the Edit Event menu (refer to Event on page 80) with the following exceptions. In the Edit Schedule menu, the event type cannot be changed. Also, the Holiday feature cannot be accessed from the Edit Schedule menu.

For instructions on changing the features in the Edit Schedule menu, refer to Edit Event on page 83.

* This setting applies only to Pressurized Spectra IV dome systems.

62	C3412M-D (12/08)

Image 62

Pelco C3412M-D manual Activate AUX Command, AUX Time, Edit Schedule

Contents

Spectra IV and Spectra IV SE Series Page Contents Wide Dynamic Range Field Align Repeat Ack Action Activate Aux Current Reading Reset Alert Welcome SW2 Switch 1 AD-32 Preset System InstallationSwitch Settings SW2 Switch 2 CM9502 Setting SW2 Switch 3 Control System Compatibility SW2 Switches 4-5 Serial Port Settings Dome Drive Installation SW2 Switches 6-8 Baud Settings Table A. Switch Settings for SW1 P-Type Control Table B. Switch Settings for SW1 D-Type Control OFF Table B. Switch Settings for SW1 D-Type Control 100 106 141 176 211 246 Getting Started How to Operate Your Dome System Operation Accessing Main Menu Preset Quick Programming Guide CM9500 Endura Workstation VCD5000 16X LowLight Color Menu Tree Edit the Password Clock Event Dome SettingsLine Sync Presets AUX 18X LowLight Day/Night Menu Tree Edit the Password Clock Line Sync Presets PatternsAlarms AUX Title Text 22X EXview LowLight Color Menu Tree Alarms Alarm Settings Line Sync 23X LowLight Day/Night Menu Tree Edit Detection Areas Patterns 35X LowLight Day/Night Menu Tree Edit Detection Areas Spectra Language ACK Alert Reset CameraLanguage Exit Address SW2 1 32 PRESETS. OFF DIP Switch InformationDIP Switch Information System Information Restore Factory Defaults Back Exit Display SetupExit Display Setup Preset Label Title Text Save and Exit Cancel and Exit Help XXX.XX Camera Dome SettingsExit Dome Settings Camera Type of Lighting Back Exit Camera Advanced Settings Back ExitZoom Limit Zoom Speed LOW Light Limit IR CUT Filter Applies only to 18X, 23X, and 35X models AGC Limit Advanced Camera SettingsShutter Speed Back Exit Auto IrisAuto White Balance Gain B Gain Auto Sharpness Auto White Balance Video Level Dome Settings ACK Alert Reset CameraBacklight Compensation BLC Auto Iris Level Auto Iris Peak Sensor Scan Mode Field Align Electronic Image Stabilization Image Enhancement LOW LUX Noise Reduction Wide Dynamic Range Applies only to 23X and 35X models Auto Flip Proportional PAN Back Exit Motion Exit Dome Settings Camera Motion Power UPPark Time Preset Freeze Frame Scan Speed Limit Stops Azimuth Zero Back Exit Power UP Power UP Action Power UPPower UP Action Back Exit Line Sync Line Sync Phase Line Sync Presets Model Number of Stored Presets Abcdefghij Cancel Klmnopqrst Uvwxyz Space Back Exit Presets Preset NumberLabel for Preset Preset Number C3412M-D 12/08 Edit Schedule Clear Preset Clear Camera Settings Back Exit Enable Motion DetectionPresets Preset Number Preset not Defined Edit Detection Areas Motion Detection Areas Edit Schedule Activate AUX CommandAUX Time Back Exit Patterns PatternsPatterns Zones Zones Style Window BlankingBack Exit Window Blanking SET Windows Back Exit Clear Window Enable Window Reverse Clear Window Back ExitReverse Blank ALL ABOVE/BLANK ALL below Window Blank Tilt Angles Alarms C3412M-D 12/08 Default Normally open Dwell Time Secs Edit Schedule Back Exit Back Exit AUX AUX 1 Mode Toggle Dwell Time Secs AUX 2 ModeAUX Edit Title Text Title TextBack Exit Title Text Alert Repeat Activate AUX Reset AlertACK Action Current Reading Clear Back Exit Edit the Password PasswordBack Exit Password Clock Month April DAY Clock Time Base Internal ClockHour END Date Month October DAY END Time Month April Week 1ST DAY Sunday Time Base Internal ClockMM/DD/YYYY END Date Month October Week Last DAY Sunday END Time Event Holiday Event TypeBack Exit Event Event Type Event Label Back Exit Reference Information Event Label Edit Event Label Back Exit Event Event Type Event Label Edit Event Label Event Type Preset Number Back ExitEdit Event Edit Event Event Label Event Active Event Time Holiday Clear EventList Event Month January DAY Back Exit Edit HolidayEdit Holiday Occurrence Clear Holiday List Holidays Scheduled Events Event Number Event Type Label Time Occurs Holiday Cycle Camera Power Reset, Cycle Power, RebootReset Camera Reboot System Software/Language File Upload Suggested Preventative Maintenance Specifications 16X Models 18X Models DD4CBW18 22X Models DD4C22 23X Models DD4CBW23 DD4CBW23-X 35X Models DD4CBW35 DD4CBW35-X Page Product Warranty and Return Information