Installation, Switch Settings | Pelco C3412M-D specification

Installation

This manual contains installation instructions only for the Spectra IV/Spectra IV SE dome drive. For complete installation instructions for a Spectra IV/Spectra IV SE dome system, refer to the installation manual shipped with the back box.

SWITCH SETTINGS

Before installing the dome drive, configure the receiver address, termination, and baud setting. The DIP switches used to configure these settings are located on the base of the dome drive.

Figure 1 shows the default settings for the DIP switches. Switch SW1-1 (SW1, switch 1) is set to the ON position; all other switches are set to the OFF position.

Refer to the following sections to set the address, termination, and baud settings for the dome drive.

O N
SW2
1	2	3	4	5	6	7	8	9	10

SW1

O N
1	2	3	4	5	6	7	8

Figure 1. Default Switch Settings

SW1: RECEIVER ADDRESS

Set the SW1 switches for the address of the dome drive. The following information is required to set the dome drive address:

P-type control: The default address is 2. Refer to Table A on page 10 for address settings that use P-type control. The maximum number of receivers is 32.

D-type control: The default address is 1. Refer to Table B on page 11 for address settings that use D-type control. The maximum number of receivers is 254.

SW2 SWITCH 1: AD-32 PRESET SYSTEM

SW2-1 should be set to the ON position if an AD-32 controller and Pelco’s TXB-AD translator board are used to control the dome system.

SW2 SWITCH 2: CM9502 SETTING

If a CM9502 matrix system is used with the dome drive, set SW2-2 to the ON position.

C3412M-D (12/08)

7

Image 7

Pelco C3412M-D manual Installation, Switch Settings, SW1 Receiver Address, SW2 Switch 1 AD-32 Preset System

Contents

Spectra IV and Spectra IV SE Series Page Contents Field Align Wide Dynamic Range Repeat Ack Action Activate Aux Current Reading Reset Alert Welcome SW2 Switch 2 CM9502 Setting InstallationSwitch Settings SW2 Switch 1 AD-32 Preset System SW2 Switches 4-5 Serial Port Settings SW2 Switch 3 Control System Compatibility SW2 Switches 6-8 Baud Settings Dome Drive Installation Table A. Switch Settings for SW1 P-Type Control OFF Table B. Switch Settings for SW1 D-Type Control Table B. Switch Settings for SW1 D-Type Control 100 106 141 176 211 246 Getting Started Operation How to Operate Your Dome System Quick Programming Guide Accessing Main Menu Preset CM9500 VCD5000 Endura Workstation 16X LowLight Color Menu Tree AUX Dome SettingsLine Sync Presets Edit the Password Clock Event 18X LowLight Day/Night Menu Tree Title Text Line Sync Presets PatternsAlarms AUX Edit the Password Clock 22X EXview LowLight Color Menu Tree Line Sync Alarms Alarm Settings 23X LowLight Day/Night Menu Tree Edit Detection Areas Patterns 35X LowLight Day/Night Menu Tree Edit Detection Areas Exit ACK Alert Reset CameraLanguage Spectra Language System Information DIP Switch InformationDIP Switch Information Address SW2 1 32 PRESETS. OFF Exit Display Setup Preset Label Display SetupRestore Factory Defaults Back Exit XXX.XX Title Text Save and Exit Cancel and Exit Help Type of Lighting Dome SettingsExit Dome Settings Camera Camera Zoom Limit Advanced Settings Back ExitBack Exit Camera LOW Light Limit Zoom Speed Applies only to 18X, 23X, and 35X models IR CUT Filter Shutter Speed Advanced Camera SettingsAGC Limit Auto White Balance Gain B Gain Auto IrisBack Exit Auto White Balance Auto Sharpness Auto Iris Level Auto Iris Peak Dome Settings ACK Alert Reset CameraBacklight Compensation BLC Video Level Field Align Sensor Scan Mode Electronic Image Stabilization LOW LUX Noise Reduction Image Enhancement Applies only to 23X and 35X models Wide Dynamic Range Proportional PAN Auto Flip Park Time Exit Dome Settings Camera Motion Power UPBack Exit Motion Scan Speed Preset Freeze Frame Limit Stops Azimuth Zero Power UP Action Power UPBack Exit Power UP Power UP Action Line Sync Back Exit Line Sync Line Sync Phase Model Number of Stored Presets Presets Label for Preset Preset Number Back Exit Presets Preset NumberAbcdefghij Cancel Klmnopqrst Uvwxyz Space C3412M-D 12/08 Edit Detection Areas Enable Motion DetectionPresets Preset Number Preset not Defined Edit Schedule Clear Preset Clear Camera Settings Back Exit Motion Detection Areas AUX Time Activate AUX CommandEdit Schedule Patterns Zones PatternsBack Exit Patterns Zones SET Windows Back Exit Window BlankingBack Exit Window Blanking Style Reverse Enable Window Reverse Clear Window Back ExitClear Window Window Blank Tilt Angles Blank ALL ABOVE/BLANK ALL below Alarms C3412M-D 12/08 Default Normally open AUX Back Exit AUX AUX 1 Mode Toggle Dwell Time Secs AUX 2 ModeDwell Time Secs Edit Schedule Back Exit Back Exit Title Text Title TextEdit Title Text Repeat Alert Current Reading Reset AlertACK Action Activate AUX Clear Back Exit Password PasswordBack Exit Edit the Password Clock END Date Month October DAY END Time Clock Time Base Internal ClockHour Month April DAY END Date Month October Week Last DAY Sunday END Time Time Base Internal ClockMM/DD/YYYY Month April Week 1ST DAY Sunday Event Back Exit Reference Information Event TypeBack Exit Event Event Type Event Label Holiday Edit Event Label Event Label Edit Event Event Label Event Active Event Time Event Type Preset Number Back ExitEdit Event Back Exit Event Event Type Event Label Edit Event Label List Event Clear EventHoliday Edit Holiday Occurrence Edit HolidayMonth January DAY Back Exit List Holidays Clear Holiday Event Number Event Type Label Time Occurs Holiday Scheduled Events Reboot System Reset, Cycle Power, RebootReset Camera Cycle Camera Power Software/Language File Upload Suggested Preventative Maintenance 16X Models Specifications DD4CBW18 18X Models DD4C22 22X Models DD4CBW23 23X Models DD4CBW23-X DD4CBW35 35X Models DD4CBW35-X Page Product Warranty and Return Information