Dome Drive Installation | Pelco C3412M-D guide

SW2 SWITCHES 6–8: BAUD SETTINGS

Pelco’s D-type controllers are set for 2400 baud. The default setting for the dome drive is 2400 baud. If you are using a Pelco D-type controller, do not reset SW2 switches 1–3 or SW2 switches 6–8.

P-type controllers can operate at 2400, 4800, and 9600 baud. Set the SW2 switches (6, 7, and 8), located on the base of the dome drive, to the same baud as the P-type controller.

Switch Number		SW2-6	SW2-7	SW2-8

2400	Baud (default for D-type control)	Off	Off	Off

4800	Baud (default for P-type control)	On	Off	Off

9600	Baud	Off	On	Off

SW2 Switch 9: Coaxial/UTP Cable

SW2-9 should be set to the OFF position (default) if you are using coaxial cable. If you are using unsheilded twisted pair (UTP) cable, set SW2-9 to the ON position.

SW2 Switch 10: Termination Setting

When connecting more than one Spectra IV/Spectra IV SE dome system to a single controller, terminate the unit farthest from the controller. Termination is only required for the last dome in the series.

The dome drive is shipped from the factory in the unterminated (OFF) position. To terminate the dome drive, set SW2-10 to the ON position.

Note: Dome termination is not required for Coaxitron® control.

DOME DRIVE INSTALLATION

Install the dome drive. Align the blue and red tabs with the blue and red arrows on the hinged door inside the back box. Push the tabs in. Insert one side and then the other side. Continue pushing on the ends of the tabs until both sides click into place (refer to Figure 2). To use your dome system, refer to Getting Started on page 19.

Figure 2. Dome Drive Installation

Note: When removing a dome drive that has been in use, caution should be taken to avoid direct contact with the top plate of the unit. This section of the unit will be warm to the touch when first removed from an operating unit.

C3412M-D (12/08)

9

Image 9

Pelco C3412M-D manual Dome Drive Installation, SW2 Switches 6-8 Baud Settings

Contents

Spectra IV and Spectra IV SE Series Page Contents Field Align Wide Dynamic Range Repeat Ack Action Activate Aux Current Reading Reset Alert Welcome Switch Settings InstallationSW2 Switch 1 AD-32 Preset System SW2 Switch 2 CM9502 Setting SW2 Switches 4-5 Serial Port Settings SW2 Switch 3 Control System Compatibility SW2 Switches 6-8 Baud Settings Dome Drive Installation Table A. Switch Settings for SW1 P-Type Control OFF Table B. Switch Settings for SW1 D-Type Control Table B. Switch Settings for SW1 D-Type Control 100 106 141 176 211 246 Getting Started Operation How to Operate Your Dome System Quick Programming Guide Accessing Main Menu Preset CM9500 VCD5000 Endura Workstation 16X LowLight Color Menu Tree Line Sync Presets Dome SettingsEdit the Password Clock Event AUX 18X LowLight Day/Night Menu Tree Alarms AUX Line Sync Presets PatternsEdit the Password Clock Title Text 22X EXview LowLight Color Menu Tree Line Sync Alarms Alarm Settings 23X LowLight Day/Night Menu Tree Edit Detection Areas Patterns 35X LowLight Day/Night Menu Tree Edit Detection Areas Language ACK Alert Reset CameraSpectra Language Exit DIP Switch Information DIP Switch InformationAddress SW2 1 32 PRESETS. OFF System Information Display Setup Exit Display Setup Preset LabelRestore Factory Defaults Back Exit XXX.XX Title Text Save and Exit Cancel and Exit Help Exit Dome Settings Camera Dome SettingsCamera Type of Lighting Advanced Settings Back Exit Zoom LimitBack Exit Camera LOW Light Limit Zoom Speed Applies only to 18X, 23X, and 35X models IR CUT Filter Advanced Camera Settings Shutter SpeedAGC Limit Auto Iris Auto White Balance Gain B GainBack Exit Auto White Balance Auto Sharpness Backlight Compensation BLC Dome Settings ACK Alert Reset CameraVideo Level Auto Iris Level Auto Iris Peak Field Align Sensor Scan Mode Electronic Image Stabilization LOW LUX Noise Reduction Image Enhancement Applies only to 23X and 35X models Wide Dynamic Range Proportional PAN Auto Flip Exit Dome Settings Camera Motion Power UP Park TimeBack Exit Motion Scan Speed Preset Freeze Frame Limit Stops Azimuth Zero Power UP Power UP ActionBack Exit Power UP Power UP Action Line Sync Back Exit Line Sync Line Sync Phase Model Number of Stored Presets Presets Back Exit Presets Preset Number Label for Preset Preset NumberAbcdefghij Cancel Klmnopqrst Uvwxyz Space C3412M-D 12/08 Presets Preset Number Preset not Defined Enable Motion DetectionEdit Schedule Clear Preset Clear Camera Settings Back Exit Edit Detection Areas Motion Detection Areas Activate AUX Command AUX TimeEdit Schedule Patterns Patterns ZonesBack Exit Patterns Zones Back Exit Window Blanking Window BlankingStyle SET Windows Back Exit Enable Window Reverse Clear Window Back Exit ReverseClear Window Window Blank Tilt Angles Blank ALL ABOVE/BLANK ALL below Alarms C3412M-D 12/08 Default Normally open Back Exit AUX AUX 1 Mode Toggle Dwell Time Secs AUX 2 Mode AUXDwell Time Secs Edit Schedule Back Exit Title Text Back Exit Title TextEdit Title Text Repeat Alert ACK Action Reset AlertActivate AUX Current Reading Clear Password Back Exit PasswordBack Exit Edit the Password Clock Hour Clock Time Base Internal ClockMonth April DAY END Date Month October DAY END Time MM/DD/YYYY Time Base Internal ClockMonth April Week 1ST DAY Sunday END Date Month October Week Last DAY Sunday END Time Event Back Exit Event Event Type Event Label Event TypeHoliday Back Exit Reference Information Edit Event Label Event Label Edit Event Event Type Preset Number Back ExitBack Exit Event Event Type Event Label Edit Event Label Edit Event Event Label Event Active Event Time Clear Event List EventHoliday Edit Holiday Edit Holiday OccurrenceMonth January DAY Back Exit List Holidays Clear Holiday Event Number Event Type Label Time Occurs Holiday Scheduled Events Reset Camera Reset, Cycle Power, RebootCycle Camera Power Reboot System Software/Language File Upload Suggested Preventative Maintenance 16X Models Specifications DD4CBW18 18X Models DD4C22 22X Models DD4CBW23 23X Models DD4CBW23-X DD4CBW35 35X Models DD4CBW35-X Page Product Warranty and Return Information