Park Time, Back Exit Motion | Pelco C3412M-D instruction

SPECTRA IV

LANGUAGE

<SYSTEM INFORMATION> <DISPLAY SETUP> <DOME SETTINGS>

ACK ALERT*

RESET CAMERA

CYCLE CAMERA POWER REBOOT SYSTEM

EXIT

DOME SETTINGS

<CAMERA>

<MOTION>

<POWER UP>

<LINE SYNC> <PRESETS> <PATTERNS> <ZONES>

<WINDOW BLANKING> <ALARMS>

<AUX>

<TITLE TEXT> <ALERT>* <CLEAR> <PASSWORD> <CLOCK> <EVENT>

BACK

EXIT

MOTION

AUTO FLIP PROPORTIONAL PAN PARK TIME (MINUTES)

PARK ACTION SCAN SPEED (DEG/S) PRESET FREEZE FRAME

LIMIT STOPS

<SET MANUAL STOPS> <CLEAR MANUAL STOPS> <SET SCAN STOPS> <CLEAR SCAN STOPS>

<SET AZIMUTH ZERO> <CLEAR AZIMUTH ZERO>

BACK

EXIT

REFERENCE INFORMATION MANUAL LIMITS SET SCAN LIMITS SET

PARK TIME

This feature allows the dome to begin a specified operation (scan, preset, or pattern) after a programmed time of inactivity.

Park time can be programmed from 1–720 minutes (12 hours), or set to zero, which disables this feature. The default setting is zero.

Park Action

This feature will define the activity when the dome parks. The following settings are available: NONE (default): No action.

AUTO SCAN: Dome starts auto scan operation.

RANDOM SCAN: Dome starts random scan operation.

FRAME SCAN: Dome starts frame scan operation.

PRESET 1: Dome goes to preset 1.

PRESET 8: Dome goes to preset 8.

PATTERN 1: Dome runs pattern 1.

PATTERN 2: Dome runs pattern 2.

PATTERN 3: Dome runs pattern 3.

PATTERN 4: Dome runs pattern 4.

PATTERN 5: Dome runs pattern 5.

PATTERN 6: Dome runs pattern 6.

PATTERN 7: Dome runs pattern 7.

PATTERN 8: Dome runs pattern 8.

(Only 22X, 23X, and 35X models allow PATTERN 2 through PATTERN 8.)

* This setting applies only to Pressurized Spectra IV dome systems.

C3412M-D (12/08)

51

Image 51

Pelco C3412M-D manual Park Time, Exit Dome Settings Camera Motion Power UP, Back Exit Motion

Contents

Spectra IV and Spectra IV SE Series Page Contents Field Align Wide Dynamic Range Repeat Ack Action Activate Aux Current Reading Reset Alert Welcome SW2 Switch 2 CM9502 Setting InstallationSwitch Settings SW2 Switch 1 AD-32 Preset System SW2 Switches 4-5 Serial Port Settings SW2 Switch 3 Control System Compatibility SW2 Switches 6-8 Baud Settings Dome Drive Installation Table A. Switch Settings for SW1 P-Type Control OFF Table B. Switch Settings for SW1 D-Type Control Table B. Switch Settings for SW1 D-Type Control 100 106 141 176 211 246 Getting Started Operation How to Operate Your Dome System Quick Programming Guide Accessing Main Menu Preset CM9500 VCD5000 Endura Workstation 16X LowLight Color Menu Tree AUX Dome SettingsLine Sync Presets Edit the Password Clock Event 18X LowLight Day/Night Menu Tree Title Text Line Sync Presets PatternsAlarms AUX Edit the Password Clock 22X EXview LowLight Color Menu Tree Line Sync Alarms Alarm Settings 23X LowLight Day/Night Menu Tree Edit Detection Areas Patterns 35X LowLight Day/Night Menu Tree Edit Detection Areas Exit ACK Alert Reset CameraLanguage Spectra Language System Information DIP Switch InformationDIP Switch Information Address SW2 1 32 PRESETS. OFF Display Setup Exit Display Setup Preset LabelRestore Factory Defaults Back Exit XXX.XX Title Text Save and Exit Cancel and Exit Help Type of Lighting Dome SettingsExit Dome Settings Camera Camera Advanced Settings Back Exit Zoom LimitBack Exit Camera LOW Light Limit Zoom Speed Applies only to 18X, 23X, and 35X models IR CUT Filter Advanced Camera Settings Shutter SpeedAGC Limit Auto Iris Auto White Balance Gain B GainBack Exit Auto White Balance Auto Sharpness Auto Iris Level Auto Iris Peak Dome Settings ACK Alert Reset CameraBacklight Compensation BLC Video Level Field Align Sensor Scan Mode Electronic Image Stabilization LOW LUX Noise Reduction Image Enhancement Applies only to 23X and 35X models Wide Dynamic Range Proportional PAN Auto Flip Exit Dome Settings Camera Motion Power UP Park TimeBack Exit Motion Scan Speed Preset Freeze Frame Limit Stops Azimuth Zero Power UP Power UP ActionBack Exit Power UP Power UP Action Line Sync Back Exit Line Sync Line Sync Phase Model Number of Stored Presets Presets Back Exit Presets Preset Number Label for Preset Preset NumberAbcdefghij Cancel Klmnopqrst Uvwxyz Space C3412M-D 12/08 Edit Detection Areas Enable Motion DetectionPresets Preset Number Preset not Defined Edit Schedule Clear Preset Clear Camera Settings Back Exit Motion Detection Areas Activate AUX Command AUX TimeEdit Schedule Patterns Patterns ZonesBack Exit Patterns Zones SET Windows Back Exit Window BlankingBack Exit Window Blanking Style Enable Window Reverse Clear Window Back Exit ReverseClear Window Window Blank Tilt Angles Blank ALL ABOVE/BLANK ALL below Alarms C3412M-D 12/08 Default Normally open Back Exit AUX AUX 1 Mode Toggle Dwell Time Secs AUX 2 Mode AUXDwell Time Secs Edit Schedule Back Exit Title Text Back Exit Title TextEdit Title Text Repeat Alert Current Reading Reset AlertACK Action Activate AUX Clear Password Back Exit PasswordBack Exit Edit the Password Clock END Date Month October DAY END Time Clock Time Base Internal ClockHour Month April DAY END Date Month October Week Last DAY Sunday END Time Time Base Internal ClockMM/DD/YYYY Month April Week 1ST DAY Sunday Event Back Exit Reference Information Event TypeBack Exit Event Event Type Event Label Holiday Edit Event Label Event Label Edit Event Event Label Event Active Event Time Event Type Preset Number Back ExitEdit Event Back Exit Event Event Type Event Label Edit Event Label Clear Event List EventHoliday Edit Holiday Edit Holiday OccurrenceMonth January DAY Back Exit List Holidays Clear Holiday Event Number Event Type Label Time Occurs Holiday Scheduled Events Reboot System Reset, Cycle Power, RebootReset Camera Cycle Camera Power Software/Language File Upload Suggested Preventative Maintenance 16X Models Specifications DD4CBW18 18X Models DD4C22 22X Models DD4CBW23 23X Models DD4CBW23-X DD4CBW35 35X Models DD4CBW35-X Page Product Warranty and Return Information