Backlight Compensation BLC, Video Level | Pelco C3412M-D manual

SPECTRA IV

LANGUAGE

<SYSTEM INFORMATION> <DISPLAY SETUP>

<DOME SETTINGS>

ACK ALERT*

RESET CAMERA

CYCLE CAMERA POWER REBOOT SYSTEM

EXIT

DOME SETTINGS

<CAMERA>

<MOTION> <POWER UP> <LINE SYNC> <PRESETS> <PATTERNS> <ZONES>

<WINDOW BLANKING> <ALARMS>

<AUX>

<TITLE TEXT> <ALERT>* <CLEAR> <PASSWORD> <CLOCK> <EVENT>

BACK

EXIT

CAMERA

TYPE OF LIGHTING

AUTO FOCUS

SURE FOCUS

ZOOM LIMIT

ZOOM SPEED

LOW LIGHT LIMIT

IR CUT FILTER

LOW LIGHT FOCUS

AUTO IR LEVEL

<ADVANCED SETTINGS>

BACK

EXIT

ADVANCED SETTINGS

SHUTTER SPEED AGC LIMIT AUTO IRIS

AUTO IRIS LEVEL

AUTO IRIS PEAK

AUTO SHARPNESS SHARPNESS LEVEL

AUTO WHITE BALANCE

RGAIN B GAIN

BACKLIGHT COMP

VIDEO LEVEL

SENSOR SCAN MODE FIELD ALIGN

E. IMAGE STABILIZER IMAGE ENHANCEMENT LOW LUX NOISE REDUCTION WIDE DYNAMIC RANGE

BACK

EXIT

BACKLIGHT COMPENSATION (BLC)

If a bright backlight is present, the subjects in the picture may appear dark or as a silhouette. Backlight compensation enhances objects in the center of the picture. The dome uses the center of the picture to adjust the iris. If there is a bright light source outside of this area, it will wash out to white. The camera will adjust the iris so that the object in the sensitive area is properly exposed.

There are two backlight compensation settings:

OFF (default): Backlight compensation is not activated.

ON: Backlight compensation is activated.

If backlight compensation is ON, decrease the auto iris level setting and adjust the auto IR level to a darker setting. Refer to Auto Iris Level on page 43 and Auto IR Level section on page 41.

VIDEO LEVEL

Set the video output to one of the following options:

NORMAL: 1.0 Vp-p.

HIGH (default setting): 1.2 Vp-p. to compensate for losses in video cable.

* This setting applies only to Pressurized Spectra IV dome systems.

C3412M-D (12/08)

45

Image 45

Pelco C3412M-D manual Backlight Compensation BLC, Video Level, Dome Settings ACK Alert Reset Camera

Contents

Spectra IV and Spectra IV SE Series Page Contents Field Align Wide Dynamic Range Repeat Ack Action Activate Aux Current Reading Reset Alert Welcome Switch Settings InstallationSW2 Switch 1 AD-32 Preset System SW2 Switch 2 CM9502 Setting SW2 Switches 4-5 Serial Port Settings SW2 Switch 3 Control System Compatibility SW2 Switches 6-8 Baud Settings Dome Drive Installation Table A. Switch Settings for SW1 P-Type Control OFF Table B. Switch Settings for SW1 D-Type Control Table B. Switch Settings for SW1 D-Type Control 100 106 141 176 211 246 Getting Started Operation How to Operate Your Dome System Quick Programming Guide Accessing Main Menu Preset CM9500 VCD5000 Endura Workstation 16X LowLight Color Menu Tree Line Sync Presets Dome SettingsEdit the Password Clock Event AUX 18X LowLight Day/Night Menu Tree Alarms AUX Line Sync Presets PatternsEdit the Password Clock Title Text 22X EXview LowLight Color Menu Tree Line Sync Alarms Alarm Settings 23X LowLight Day/Night Menu Tree Edit Detection Areas Patterns 35X LowLight Day/Night Menu Tree Edit Detection Areas Language ACK Alert Reset CameraSpectra Language Exit DIP Switch Information DIP Switch InformationAddress SW2 1 32 PRESETS. OFF System Information Display Setup Exit Display Setup Preset LabelRestore Factory Defaults Back Exit XXX.XX Title Text Save and Exit Cancel and Exit Help Exit Dome Settings Camera Dome SettingsCamera Type of Lighting Advanced Settings Back Exit Zoom LimitBack Exit Camera LOW Light Limit Zoom Speed Applies only to 18X, 23X, and 35X models IR CUT Filter Advanced Camera Settings Shutter SpeedAGC Limit Auto Iris Auto White Balance Gain B GainBack Exit Auto White Balance Auto Sharpness Backlight Compensation BLC Dome Settings ACK Alert Reset CameraVideo Level Auto Iris Level Auto Iris Peak Field Align Sensor Scan Mode Electronic Image Stabilization LOW LUX Noise Reduction Image Enhancement Applies only to 23X and 35X models Wide Dynamic Range Proportional PAN Auto Flip Exit Dome Settings Camera Motion Power UP Park TimeBack Exit Motion Scan Speed Preset Freeze Frame Limit Stops Azimuth Zero Power UP Power UP ActionBack Exit Power UP Power UP Action Line Sync Back Exit Line Sync Line Sync Phase Model Number of Stored Presets Presets Back Exit Presets Preset Number Label for Preset Preset NumberAbcdefghij Cancel Klmnopqrst Uvwxyz Space C3412M-D 12/08 Presets Preset Number Preset not Defined Enable Motion DetectionEdit Schedule Clear Preset Clear Camera Settings Back Exit Edit Detection Areas Motion Detection Areas Activate AUX Command AUX TimeEdit Schedule Patterns Patterns ZonesBack Exit Patterns Zones Back Exit Window Blanking Window BlankingStyle SET Windows Back Exit Enable Window Reverse Clear Window Back Exit ReverseClear Window Window Blank Tilt Angles Blank ALL ABOVE/BLANK ALL below Alarms C3412M-D 12/08 Default Normally open Back Exit AUX AUX 1 Mode Toggle Dwell Time Secs AUX 2 Mode AUXDwell Time Secs Edit Schedule Back Exit Title Text Back Exit Title TextEdit Title Text Repeat Alert ACK Action Reset AlertActivate AUX Current Reading Clear Password Back Exit PasswordBack Exit Edit the Password Clock Hour Clock Time Base Internal ClockMonth April DAY END Date Month October DAY END Time MM/DD/YYYY Time Base Internal ClockMonth April Week 1ST DAY Sunday END Date Month October Week Last DAY Sunday END Time Event Back Exit Event Event Type Event Label Event TypeHoliday Back Exit Reference Information Edit Event Label Event Label Edit Event Event Type Preset Number Back ExitBack Exit Event Event Type Event Label Edit Event Label Edit Event Event Label Event Active Event Time Clear Event List EventHoliday Edit Holiday Edit Holiday OccurrenceMonth January DAY Back Exit List Holidays Clear Holiday Event Number Event Type Label Time Occurs Holiday Scheduled Events Reset Camera Reset, Cycle Power, RebootCycle Camera Power Reboot System Software/Language File Upload Suggested Preventative Maintenance 16X Models Specifications DD4CBW18 18X Models DD4C22 22X Models DD4CBW23 23X Models DD4CBW23-X DD4CBW35 35X Models DD4CBW35-X Page Product Warranty and Return Information