Alarms, Back Exit | Pelco C3412M-D specs

ALARMS

SPECTRA IV

LANGUAGE

<SYSTEM INFORMATION> <DISPLAY SETUP> <DOME SETTINGS>

ACK ALERT*

RESET CAMERA

CYCLE CAMERA POWER REBOOT SYSTEM

EXIT

DOME SETTINGS

<CAMERA>

<MOTION> <POWER UP> <LINE SYNC> <PRESETS> <PATTERNS> <ZONES>

<WINDOW BLANKING> <ALARMS>

<AUX>

<TITLE TEXT> <ALERT>* <CLEAR> <PASSWORD> <CLOCK> <EVENT>

BACK

EXIT

ALARMS

RESUME

SEQUENCE (SECS)

RESET DELAY (SECS)

<ALARM SETTINGS>

BACK

EXIT

ALARM SETTINGS

ALARM NUMBER

ALARM PRIORITY ALARM ACTION ACTIVATE AUX ALARM CONTACT <EDIT SCHEDULE>

BACK

EXIT

The Spectra IV SE dome systems have seven alarm inputs that can be programmed as high, medium, or low priority. When an alarm is received, an input signal to the dome triggers the user- defined action (go to preset, run pattern, etc.) programmed for the alarm.

Note: Refer to the notation in step 6 for the limited alarm features available for 16X and 18X models.

There are three global alarm settings:

RESUME: This mode lets the dome resume its previous activity (scan, pattern, or previous position) after all alarms are cleared.

SEQUENCE: This is the time the dome will perform an alarm activity when more than one alarm of the same priority occurs at the same time.

RESET DELAY: This is the amount of time the dome considers the alarm to be active after it has physically cleared.

Use the following steps to program alarm settings.

1.Use the joystick to position the cursor beside ALARM SETTINGS. Press Iris Open.

2.Select the alarm number:

a.Use the joystick to position the cursor beside ALARM NUMBER.

b.Press Iris Open. The cursor moves to the right.

c.Move the joystick up or down to view selections. Press Iris Open to enter selection.

* This setting applies only to Pressurized Spectra IV dome systems.

68	C3412M-D (12/08)

Image 68

Pelco C3412M-D manual Alarms, Back Exit

Contents

Spectra IV and Spectra IV SE Series Page Contents Wide Dynamic Range Field Align Repeat Ack Action Activate Aux Current Reading Reset Alert Welcome Installation Switch SettingsSW2 Switch 1 AD-32 Preset System SW2 Switch 2 CM9502 Setting SW2 Switch 3 Control System Compatibility SW2 Switches 4-5 Serial Port Settings Dome Drive Installation SW2 Switches 6-8 Baud Settings Table A. Switch Settings for SW1 P-Type Control Table B. Switch Settings for SW1 D-Type Control OFF Table B. Switch Settings for SW1 D-Type Control 100 106 141 176 211 246 Getting Started How to Operate Your Dome System Operation Accessing Main Menu Preset Quick Programming Guide CM9500 Endura Workstation VCD5000 16X LowLight Color Menu Tree Dome Settings Line Sync PresetsEdit the Password Clock Event AUX 18X LowLight Day/Night Menu Tree Line Sync Presets Patterns Alarms AUXEdit the Password Clock Title Text 22X EXview LowLight Color Menu Tree Alarms Alarm Settings Line Sync 23X LowLight Day/Night Menu Tree Edit Detection Areas Patterns 35X LowLight Day/Night Menu Tree Edit Detection Areas ACK Alert Reset Camera LanguageSpectra Language Exit DIP Switch Information DIP Switch InformationAddress SW2 1 32 PRESETS. OFF System Information Restore Factory Defaults Back Exit Display SetupExit Display Setup Preset Label Title Text Save and Exit Cancel and Exit Help XXX.XX Dome Settings Exit Dome Settings CameraCamera Type of Lighting Back Exit Camera Advanced Settings Back ExitZoom Limit Zoom Speed LOW Light Limit IR CUT Filter Applies only to 18X, 23X, and 35X models AGC Limit Advanced Camera SettingsShutter Speed Back Exit Auto IrisAuto White Balance Gain B Gain Auto Sharpness Auto White Balance Dome Settings ACK Alert Reset Camera Backlight Compensation BLCVideo Level Auto Iris Level Auto Iris Peak Sensor Scan Mode Field Align Electronic Image Stabilization Image Enhancement LOW LUX Noise Reduction Wide Dynamic Range Applies only to 23X and 35X models Auto Flip Proportional PAN Back Exit Motion Exit Dome Settings Camera Motion Power UPPark Time Preset Freeze Frame Scan Speed Limit Stops Azimuth Zero Back Exit Power UP Power UP Action Power UPPower UP Action Back Exit Line Sync Line Sync Phase Line Sync Presets Model Number of Stored Presets Abcdefghij Cancel Klmnopqrst Uvwxyz Space Back Exit Presets Preset NumberLabel for Preset Preset Number C3412M-D 12/08 Enable Motion Detection Presets Preset Number Preset not DefinedEdit Schedule Clear Preset Clear Camera Settings Back Exit Edit Detection Areas Motion Detection Areas Edit Schedule Activate AUX CommandAUX Time Back Exit Patterns PatternsPatterns Zones Zones Window Blanking Back Exit Window BlankingStyle SET Windows Back Exit Clear Window Enable Window Reverse Clear Window Back ExitReverse Blank ALL ABOVE/BLANK ALL below Window Blank Tilt Angles Alarms C3412M-D 12/08 Default Normally open Dwell Time Secs Edit Schedule Back Exit Back Exit AUX AUX 1 Mode Toggle Dwell Time Secs AUX 2 ModeAUX Edit Title Text Title TextBack Exit Title Text Alert Repeat Reset Alert ACK ActionActivate AUX Current Reading Clear Back Exit Edit the Password PasswordBack Exit Password Clock Clock Time Base Internal Clock HourMonth April DAY END Date Month October DAY END Time Time Base Internal Clock MM/DD/YYYYMonth April Week 1ST DAY Sunday END Date Month October Week Last DAY Sunday END Time Event Event Type Back Exit Event Event Type Event LabelHoliday Back Exit Reference Information Event Label Edit Event Label Event Type Preset Number Back Exit Edit EventBack Exit Event Event Type Event Label Edit Event Label Edit Event Event Label Event Active Event Time Holiday Clear EventList Event Month January DAY Back Exit Edit HolidayEdit Holiday Occurrence Clear Holiday List Holidays Scheduled Events Event Number Event Type Label Time Occurs Holiday Reset, Cycle Power, Reboot Reset CameraCycle Camera Power Reboot System Software/Language File Upload Suggested Preventative Maintenance Specifications 16X Models 18X Models DD4CBW18 22X Models DD4C22 23X Models DD4CBW23 DD4CBW23-X 35X Models DD4CBW35 DD4CBW35-X Page Product Warranty and Return Information