
10Using other functions
The front panel display shows each of the following settings for two seconds each:
Input source | Listening mode |
|
|
Signal select | Surround Back Processing |
|
|
Video Select | MCACC Position |
|
|
Room 2 / REC SEL | Room 3 |
|
|
2When you’re finished, press STATUS again to switch off the display.
Resetting the system
Use this procedure to reset all the receiver’s settings to the factory default. Use the front panel controls to do this.
1Switch the receiver into standby.
2While holding down the front panel AV
PARAMETER button, press and hold STANDBY/ON for about three seconds.
The display shows RESET?.
3Press the front panel ENTER button. The display shows RESET OK?.
4Press SETUP to confirm.
OK appears in the display to indicate that the receiver has been reset to the factory default settings.
•Note that all settings will be saved, even if the receiver is unplugged.
Default system settings
Setting |
| Default | |
HDMI Audio |
| Amp | |
|
|
|
|
Digital Video Conversion |
| On | |
|
|
|
|
Speakers |
| A | |
|
|
|
|
Surround Back System |
| Normal (SBch) | |
|
|
|
|
Speaker System | Front | SMALL | |
|
|
|
|
|
| Center | SMALL |
|
|
|
|
|
| Surr. | SMALL |
|
|
|
|
|
| SB | SMALLx2 |
|
|
|
|
|
| SW | YES |
|
|
| |
Crossover |
| 80 Hz | |
|
|
| |
Bass Peak Level |
| OFF | |
|
|
| |
| OFF | ||
|
|
| |
THX Audio Setting |
|
Inputs
See Input function default and possible settings on page 61.
66
Setting |
| Default | |
Multi Room |
|
| |
|
|
|
|
Room 2 Volume Type |
| Variable | |
|
|
|
|
Room 2 IR Receiver Type |
| SETTING 1 | |
|
|
|
|
Room 2 Volume |
| ||
|
|
|
|
SR+ |
|
| |
|
|
|
|
SR+ Control On/Off |
| OFF | |
|
|
| |
SR+ Volume Control On/Off | OFF | ||
|
|
|
|
Monitor Out |
| OFF | |
|
|
|
|
DSP |
|
| |
|
|
| |
MCACC Position Memory | M1: MEMORY 1 | ||
|
|
|
|
Surround back channel |
| ON | |
Processing |
|
| |
|
|
|
|
Phase Control |
| On | |
|
|
|
|
Sound Delay |
| 0 frame | |
|
|
|
|
Dual Mono |
| CH1 | |
|
|
|
|
DRC |
| OFF | |
|
|
|
|
SACD Gain |
| 0 dB | |
|
|
|
|
Digital Safety |
| OFF | |
|
|
|
|
Effect Level | 7 ch Stereo | 90 | |
|
|
|
|
|
| Other modes | 50 |
|
|
| |
2PL II Music Options | Center Width | 3 | |
|
|
|
|
|
| Dimension | 0 |
|
|
|
|
|
| Panorama | OFF |
|
|
| |
Neo:6 Options | Center Image | 3 | |
|
|
| |
All Inputs | Listening Mode (2 ch) | AUTO SURROUND | |
|
|
|
|
|
| Listening Mode (x ch) | AUTO SURROUND |
|
|
|
|
|
| Listening Mode (HP) | STEREO |
See also Setting the AV options on page 63 for other default DSP settings.
MCACC
Channel level |
| 0 dB |
|
| |
Speaker Distance | 3.0 m | |
|
|
|
Standing Wave | Standing Wave On/ | ON |
Off |
| |
|
|
|
| ATT | 0 dB |
|
|
|
| SWch Wide Trim | 0.0 |
|
|
|
EQ Data | All channels/bands | 0 dB |
|
|
|
EQ Wide Trim |
| 0.0 dB |
|
|
|
En