11Using other functions
Reducing the level of an analog signal
The input attenuator lowers the input level of an analog signal when it’s too strong. You can use this if you find the that the OVER indicator is lights often, or you can
hear distortion in the sound.1
1 | 2 | 3 |
|
|
GENRE | MCACC | SLEEP | AUDIO DISPLAY | CH |
4 | 5 | 6 |
|
|
SR+ | SBch | A.ATT | TV CTRL | RECEIVER |
7 | 8 | 9 |
|
|
D.ACCESS | CH LEVEL | CLASS |
|
|
| 0 | ENTER |
|
|
| INPUT | MASTER | MAIN | ZONE 2 |
| VOLUME |
|
|
•Press RECEIVER, then press A.ATT to switch the input attenuator on or off.
Using the sleep timer
The sleep timer switches the receiver into standby after a specified amount of time so you can fall asleep without worrying about the receiver being left on all night. Use the remote control to set the sleep timer.
INPUT | DIMMER | AUDIO DISPLAY | CH | |
SELECT | ||||
|
|
•Press RECEIVER, then press DIMMER repeatedly to change the brightness of the front panel display.
Switching the speaker impedance
We recommend using speakers of 8 Ω with this system, but it is possible to switch the impedance setting if you plan to use speakers with a 6 Ω impedance rating. Use the front panel controls to do this.
•With the receiver in standby, press STANDBY/
ON while holding down the SPEAKERS button. Each time you do this, you switch between the impedance settings:
•Speaker 6 Ω – Use this setting if your speakers are rated at 6 Ω.
•Speaker 8 Ω – Use this setting if your speakers are rated at 8 Ω or more.
Checking your system settings
Use the status display screen to check your current settings for features such as surround back channel processing and your current MCACC preset.
1 2 3
GENRE | MCACC | SLEEP | TV CTRL | RECEIVER | THX | STATUS | PHASE |
4 
5 6
SR+ | SBch | A.ATT |
|
| |
7 | 8 | 9 | MAIN | ZONE 2 | |
D.ACCESS | CH LEVEL | CLASS | |||
|
| ||||
| 0 | ENTER |
|
|
•Press RECEIVER, then press SLEEP repeatedly to set the sleep time.
30 min | 60 min |
Off | 90 min |
•You can check the remaining sleep time at any time by pressing SLEEP once. Pressing repeatedly will cycle through the sleep options again.2
Dimming the display
You can choose between four brightness levels for the front panel display. Note that when selecting sources, the display automatically brightens for a few seconds.
|
| DTV/TV | EON | MPX SIGNAL SEL |
FM/AM |
| iPod USB |
| CH |
|
| AUDIO | DISPLAY | |
INPUT | DIMMER |
|
| |
SELECT |
| RECEIVER | ||
1 | 2 | TV CTRL |
| |
3 |
|
| ||
GENRE | MCACC | SLEEP |
|
|
4 | 5 | 6 |
|
|
SR+ | SBch | A.ATT | MAIN | ZONE 2 |
|
|
| ||
7 8 9
DTV/TV | EON | MPX SIGNAL SEL |
AUDIO | DISPLAY | CH |
TV CTRL |
| RECEIVER |
1Press RECEIVER, then press STATUS to check the system settings.
These appear on the front panel display.3
The front panel display shows each of the following settings for three seconds each:
Input source
↓
Surround Back Processing
↓
MCACC preset
↓
ZONE 2
↓
HDMI Control
2When you’re finished, press STATUS again to switch off the display.
Note
1The attenuator isn’t available with digital sources, or when using the Stream Direct modes.
2You can also switch off the sleep timer simply by switching off the receiver.
3If the Pure Direct mode is switched on, some settings above will show OFF, even though they are on.
72
En
