Additional information | 13 |
SymptomRemedy
No sound from the surround or center speakers.
•Check that the Stereo listening mode or the Front Stage Surround Advance mode isn’t selected; select one of the surround listening modes (see Listening in surround sound on page 29).
•Check that the surround/center speakers are not set to NO (see Speaker Setting on page 48).
•Check the channel level settings (see Channel Level on page 48).
| • Check the speaker connections (see Connecting the speakers on page 20). |
|
|
No sound from surround back | • Check that the surround back speakers are set to LARGE or SMALL (see Speaker Setting on |
speakers. | page 48). |
| • Make sure surround back processing is set to SBch ON (see Using surround back channel |
| processing on page 33). |
| • If the source is Dolby Surround EX or |
| surround back processing set to SBch Auto, there will be no sound from the surround back |
| speakers. In this case, set to SBch ON (see Using surround back channel processing on page 33). |
| • If the source does not have 6.1 playback channels, make sure that surround back processing is set |
| to SBch ON and a surround mode is selected (see Listening in surround sound on page 29). |
| • Check the speaker connections (see Connecting the speakers on page 20). If only one surround |
| back speaker is connected, make sure it’s connected to the left channel speaker terminal. |
|
|
No sound from subwoofer. | • Check that the subwoofer is connected properly, switched on and the volume turned up. |
| • If your subwoofer has a sleep function, make sure it is switched off. |
| • Make sure that the Subwoofer setting is YES or PLUS (see Speaker Setting on page 48). |
| • The crossover frequency may be set too low; try setting it higher to match the characteristics of |
| your other speakers (see Speaker Setting on page 48). |
| • If there is very little low frequency information in the source material, change your speaker settings |
| to Front: SMALL / Subwoofer: YES, or Front: LARGE / Subwoofer: PLUS (see Speaker Setting on |
| page 48). |
| • Check that the LFE channel is not set to OFF, or a very quiet setting (see Setting the Audio options |
| on page 69). |
| • Check the speaker level settings (see Channel Level on page 48). |
|
|
No sound from one speaker. | • Check the speaker connection (see Connecting the speakers on page 20). |
| • Check the speaker level settings (see Channel Level on page 48). |
| • Check that the speaker hasn’t been set to NO (see Speaker Setting on page 48). |
| • The channel may not be recorded in the source. By using one of the advanced effect listening |
| mode, you may be able to create the missing channel (see Listening in surround sound on page 29). |
|
|
Sound is produced from | • Check that the input signal type is set to DIGITAL (see Choosing the input signal on page 32). |
analog components, but not | • Make sure that the digital input is assigned correctly for the input jack the component is connected |
from digital ones (DVD, LD, CD- | to (see The Input Setup menu on page 65). |
ROM, etc.). | • Check the digital output settings on the source component. |
| |
| • If the source component has a digital volume control, make sure this is not turned down. |
| • Make sure that the multichannel analog inputs are not selected. Select any other input source. |
|
|
No sound is output or a noise is | • Check that your DVD player is compatible with Dolby Digital/DTS discs. |
output when Dolby Digital/DTS | • Check the digital output settings of your DVD player. Make sure that the DTS signal output is set |
software is played back. | to On. |
| • If the source component has a digital volume control, make sure this is not turned down. |
|
|
No sound when using the | • If the HDMI input source is selected, sound is muted until exiting either menu. |
System Setup or Status menu. | • If sound is muted in the sub zone (ZONE 2), it will be restored after exiting the System Setup menu. |
|
|
79
En
