If You Cannot Make Copies As You Want

 

 

 

 

 

 

 

 

 

Problem

Causes

Solutions

 

 

 

 

 

 

 

 

 

In Image Repeat mode, the

You selected copy paper

Select copy paper larger than the

 

 

original image is not cop-

the same size as the origi-

originals.

 

 

 

ied repeatedly.

nals, or you did not select

 

 

 

 

 

 

Select the proper reproduction ratio.

 

 

 

the proper reproduction

 

 

 

 

 

 

 

 

ratio.

 

 

 

 

 

 

 

 

 

The stamp position is

The paper orientation is

Check the paper orientation and

 

 

wrong.

wrong.

stamp position.

 

 

 

 

 

 

 

 

When using Combine,

You specified a reproduc-

When you specify a reproduction

 

 

parts of the image are not

tion ratio that does not

ratio using Manual Paper Select

 

 

copied.

match the sizes of your

mode, make sure the ratio matches

 

 

 

originals and copy paper.

your originals and the copy paper.

 

 

 

 

 

Note

 

 

 

 

 

 

❒ Select the correct reproduction

 

 

 

 

 

ratio before using Combine

 

 

 

 

 

mode.

 

 

 

 

 

 

 

 

Order of copies is not cor-

You placed originals in in-

When placing a stack of originals in

 

 

 

5

rect.

correct order.

the ADF, the last page should be at

 

 

 

 

the bottom.

 

 

 

 

 

 

 

 

 

 

 

 

If you place an original on the expo-

 

 

 

 

 

sure glass, start with the first page to

 

 

 

 

 

be copied.

 

 

 

 

 

 

 

 

When using Duplex, copy

You placed originals in the

Place originals in the correct orien-

 

 

is made Top/Bottom even

wrong direction.

tation.

 

 

 

though Left/Right is se-

 

 

 

 

 

 

lected, or copy is made

 

 

 

 

 

 

Left/Right even though

 

 

 

 

 

 

Top/Bottom is selected.

 

 

 

 

 

 

 

 

 

 

 

Paper does not output dur-

If you stop printing while

Press the {Reset} key and cancel

 

 

ing printing with stapling.

using the staple function,

copy settings, including stapling.

 

 

 

papers not stapled during

 

 

 

 

 

printing may be left in the

 

 

 

 

 

staple unit.

 

 

 

 

 

 

 

 

 

 

 

❖ Connect Copy

 

 

 

 

 

 

 

 

 

 

 

 

Problem

Causes

Solutions

 

 

 

 

 

 

 

 

 

You cannot staple or

The main and sub-ma-

Press [

] to cancel Connect

 

 

punch.

chines are not installed

 

 

Copy.

 

 

 

 

with the same options.

 

 

 

 

 

 

 

 

 

 

 

 

 

You get different copy re-

The Copy Quality setting

Set the Copy Quantity.

 

 

sults from the main and

differ on the two machines.

 

 

 

 

sub-machines.

 

 

 

 

 

 

 

 

 

 

 

 

 

131