Manuals
/
RTS
/
Computer Equipment
/
Network Card
RTS
ADAM manual
Models:
ADAM
1
4
48
48
Download
48 pages
3.75 Kb
1
2
3
4
5
6
7
8
<
>
Specs
Install
Configuration
Intercom Alarms
Download Firmware Upgrades
Features
Cancel Button
Page 4
Image 4
Page 3
Page 5
Page 4
Image 4
Page 3
Page 5
Contents
Triple Bus Expander for ADAM
ADAM TBX - TriBus
See the enclosed warranty card for further details
of Contents
INSTALLATION AND CONFIGURATION
DOWNLOAD FIRMWARE UPGRADES
INTRODUCTION
Page
List of Figures
Page
Introduction
General Description
Version Requirements
CHAPTER
Features
Specifications
Configuration Requirements
Board Performance
Links Used
Fail-Over Modes
Full Redundancy
Partial Redundancy
Non-Redundancy
Page
Figure 2 Eight Frame Tribus System - Non-Redundant
Page
Debug Information
The Uploading Debug Information Status window appears
To find the file you just created, do the following
The AZedit debug file is made
2. Navigate to C\Telex\AZedit\Debug
Page
Installation and Configuration
Installation
To install the Tribus into an ADAM frame, do the following
Requirements
Configuration
Configure each MCII-e Master Controller IP Address for the Ethernet
To configure the IP Address for the MCII-e, do the following
1. Verify you are serially connected to AZedit
To configure the size of your frame, do the following
Configure the size of your Intercom system for each frame
The Intercom Configuration window appears
3. Click Intercom Sizing Wizard
The Select Intercom Type window appears
The Select Intercom Size window appears
6. Select the The number of frames in the intercom radio button
The Verify Intercom Configuration window appears
10. Select the Enable Test Audio recommended check box
The Select Frame Links window appears
The Intercom Configuration window reappears
15. Click Test to verify the configuration validity
16. Click Apply to apply the configuration to the intercom system
13. Click Finish
Configure the frame using the Frame Mapping window in AZedit
2. Click the Frame 2 IP Address 1 field
The field becomes active and a browse button appears
3. Click the browse button
Base 8 vs. Base 16 Port Number Systems
Base 8 Port Number System
installed
Base 16 Port Number System
To Force Autonomous Mode when no audio links are up, do the following
Force Autonomous Mode Check Box
The Intercom Configuration window appears
AZedit Connections
The Intercom Configuration window closes
Window Descriptions
Frame Mapping Table Window
Frame Column
CHAPTER
IP Address 1 Column
MAC Address 1 Column
IP Address 2 Column
MAC Address 2 Column
Base 16 Column Check Box
Move Up Button
Move Down Button
Accept Frame Mapping Table from Other Frames Check Box
Select Frame Window
Test Button
Done Button
IP Address 1 Column
Cancel Button
MAC Address 1 Column
IP Address 2 Column
MAC Address 2 Column
TBX Links Status Window
TBX Column
Comm Column
Example
A Link Up/Dn Column
A Partner Column
B Link Up/Dn Column
B Partner Column
Intercom Alarms
Audio A Column
Audio B Column
Audio C Column
To open the Intercom Alarms window, do the following
The Intercom Alarms window appears
Alarm Time Column
Hiding and Clearing Alarms
Frame Column
Resolved Time Column
Configure Logging Window
Logging Window
J1 Radio Button
J9 Radio Button
J10 Radio Button
Ethernet Radio Button
Download Firmware Upgrades
Download Firmware to the TBX-Tribus Card
CHAPTER
To download firmware to the TBX-Tribus card, do the following
The Firmware Download window appears
The Download Device Firmware window appears
7. Click Begin Download
The download begins. This takes a minute or two to occur
11. Verify the Tribus card firmware has been updated
The success message and Download Device Firmware window closes
