Manuals
/
RTS
/
Computer Equipment
/
Network Card
RTS
ADAM manual
Models:
ADAM
1
14
48
48
Download
48 pages
3.75 Kb
11
12
13
14
15
16
17
18
<
>
Specifications
Install
Warranty
Configuration
Intercom Alarms
How to
Download Firmware Upgrades
Select the Enable Test Audio recommended check box
Features
Cancel Button
Page 14
Image 14
10
Page 13
Page 15
Page 14
Image 14
Page 13
Page 15
Contents
Triple Bus Expander for ADAM
ADAM TBX - TriBus
See the enclosed warranty card for further details
DOWNLOAD FIRMWARE UPGRADES
of Contents
INSTALLATION AND CONFIGURATION
INTRODUCTION
Page
List of Figures
Page
Version Requirements
Introduction
General Description
CHAPTER
Features
Board Performance
Specifications
Configuration Requirements
Links Used
Fail-Over Modes
Full Redundancy
Partial Redundancy
Non-Redundancy
Page
Figure 2 Eight Frame Tribus System - Non-Redundant
Page
Debug Information
The Uploading Debug Information Status window appears
2. Navigate to C\Telex\AZedit\Debug
The AZedit debug file is made
To find the file you just created, do the following
Page
To install the Tribus into an ADAM frame, do the following
Installation and Configuration
Installation
Requirements
To configure the IP Address for the MCII-e, do the following
Configuration
Configure each MCII-e Master Controller IP Address for the Ethernet
1. Verify you are serially connected to AZedit
The Intercom Configuration window appears
Configure the size of your Intercom system for each frame
To configure the size of your frame, do the following
The Select Intercom Size window appears
3. Click Intercom Sizing Wizard
The Select Intercom Type window appears
6. Select the The number of frames in the intercom radio button
The Select Frame Links window appears
10. Select the Enable Test Audio recommended check box
The Verify Intercom Configuration window appears
16. Click Apply to apply the configuration to the intercom system
The Intercom Configuration window reappears
15. Click Test to verify the configuration validity
13. Click Finish
The field becomes active and a browse button appears
Configure the frame using the Frame Mapping window in AZedit
2. Click the Frame 2 IP Address 1 field
3. Click the browse button
Base 8 vs. Base 16 Port Number Systems
Base 8 Port Number System
installed
Base 16 Port Number System
The Intercom Configuration window appears
Force Autonomous Mode Check Box
To Force Autonomous Mode when no audio links are up, do the following
AZedit Connections
The Intercom Configuration window closes
Frame Column
Window Descriptions
Frame Mapping Table Window
CHAPTER
IP Address 2 Column
IP Address 1 Column
MAC Address 1 Column
MAC Address 2 Column
Move Down Button
Base 16 Column Check Box
Move Up Button
Accept Frame Mapping Table from Other Frames Check Box
Done Button
Select Frame Window
Test Button
IP Address 1 Column
IP Address 2 Column
Cancel Button
MAC Address 1 Column
MAC Address 2 Column
Comm Column
TBX Links Status Window
TBX Column
Example
B Link Up/Dn Column
A Link Up/Dn Column
A Partner Column
B Partner Column
Audio B Column
Intercom Alarms
Audio A Column
Audio C Column
To open the Intercom Alarms window, do the following
The Intercom Alarms window appears
Frame Column
Alarm Time Column
Hiding and Clearing Alarms
Resolved Time Column
Configure Logging Window
Logging Window
J10 Radio Button
J1 Radio Button
J9 Radio Button
Ethernet Radio Button
CHAPTER
Download Firmware Upgrades
Download Firmware to the TBX-Tribus Card
To download firmware to the TBX-Tribus card, do the following
7. Click Begin Download
The Firmware Download window appears
The Download Device Firmware window appears
The download begins. This takes a minute or two to occur
11. Verify the Tribus card firmware has been updated
The success message and Download Device Firmware window closes
