Manuals / RTS / Computer Equipment / Network Card

RTS ADAM manual Download Firmware Upgrades, Download Firmware to the TBX-Tribus Card, Chapter

Models: ADAM

1 48

Download 48 pages 3.75 Kb

Page 45

Image 45

CHAPTER 4

Download Firmware Upgrades

Download Firmware to the TBX-Tribus Card

To download firmware to the TBX-Tribus card, do the following:

1.From the Status menu in AZedit, select Software Versions. A flyout menu appears.

2.From the flyout menu, select IO Cards.

The I/O Card Version Information Window appears.

FIGURE 52. I/O Card Version Information Window

Page 45

Image 45

RTS ADAM manual Download Firmware Upgrades, Download Firmware to the TBX-Tribus Card, Chapter

Contents

ADAM TBX - TriBus Triple Bus Expander for ADAMSee the enclosed warranty card for further details INSTALLATION AND CONFIGURATION of ContentsDOWNLOAD FIRMWARE UPGRADES INTRODUCTIONPage List of Figures Page General Description IntroductionVersion Requirements CHAPTERFeatures Configuration Requirements SpecificationsBoard Performance Links UsedFail-Over Modes Full Redundancy Partial Redundancy Non-Redundancy Page Figure 2 Eight Frame Tribus System - Non-Redundant Page Debug Information The Uploading Debug Information Status window appears The AZedit debug file is made To find the file you just created, do the following2. Navigate to C\Telex\AZedit\Debug Page Installation Installation and ConfigurationTo install the Tribus into an ADAM frame, do the following RequirementsConfigure each MCII-e Master Controller IP Address for the Ethernet ConfigurationTo configure the IP Address for the MCII-e, do the following 1. Verify you are serially connected to AZeditConfigure the size of your Intercom system for each frame To configure the size of your frame, do the followingThe Intercom Configuration window appears The Select Intercom Type window appears 3. Click Intercom Sizing WizardThe Select Intercom Size window appears 6. Select the The number of frames in the intercom radio button10. Select the Enable Test Audio recommended check box The Verify Intercom Configuration window appearsThe Select Frame Links window appears 15. Click Test to verify the configuration validity The Intercom Configuration window reappears16. Click Apply to apply the configuration to the intercom system 13. Click Finish2. Click the Frame 2 IP Address 1 field Configure the frame using the Frame Mapping window in AZeditThe field becomes active and a browse button appears 3. Click the browse buttonBase 8 Port Number System Base 8 vs. Base 16 Port Number Systemsinstalled Base 16 Port Number System Force Autonomous Mode Check Box To Force Autonomous Mode when no audio links are up, do the followingThe Intercom Configuration window appears The Intercom Configuration window closes AZedit ConnectionsFrame Mapping Table Window Window DescriptionsFrame Column CHAPTERMAC Address 1 Column IP Address 1 ColumnIP Address 2 Column MAC Address 2 ColumnMove Up Button Base 16 Column Check BoxMove Down Button Accept Frame Mapping Table from Other Frames Check BoxTest Button Select Frame WindowDone Button IP Address 1 ColumnMAC Address 1 Column Cancel ButtonIP Address 2 Column MAC Address 2 ColumnTBX Column TBX Links Status WindowComm Column ExampleA Partner Column A Link Up/Dn ColumnB Link Up/Dn Column B Partner ColumnAudio A Column Intercom AlarmsAudio B Column Audio C ColumnThe Intercom Alarms window appears To open the Intercom Alarms window, do the followingHiding and Clearing Alarms Alarm Time ColumnFrame Column Resolved Time ColumnLogging Window Configure Logging WindowJ9 Radio Button J1 Radio ButtonJ10 Radio Button Ethernet Radio ButtonDownload Firmware to the TBX-Tribus Card Download Firmware UpgradesCHAPTER To download firmware to the TBX-Tribus card, do the followingThe Download Device Firmware window appears The Firmware Download window appears7. Click Begin Download The download begins. This takes a minute or two to occurThe success message and Download Device Firmware window closes 11. Verify the Tribus card firmware has been updated