Manuals
/
RTS
/
Computer Equipment
/
Network Card
RTS
manual Triple Bus Expander for ADAM, ADAM TBX - TriBus
Models:
ADAM
1
1
48
48
Download
48 pages
3.75 Kb
1
2
3
4
5
6
7
8
<
>
Specs
Install
Warranty
Configuration
Intercom Alarms
How to
Download Firmware Upgrades
Select the Enable Test Audio recommended check box
Features
Cancel Button
Page 1
Image 1
ADAM
TBX - TriBus
Triple Bus Expander for ADAM
93507838000 Rev A
12/2008
Page 2
Page 1
Image 1
Page 2
Contents
ADAM TBX - TriBus
Triple Bus Expander for ADAM
See the enclosed warranty card for further details
INSTALLATION AND CONFIGURATION
of Contents
DOWNLOAD FIRMWARE UPGRADES
INTRODUCTION
Page
List of Figures
Page
General Description
Introduction
Version Requirements
CHAPTER
Features
Configuration Requirements
Specifications
Board Performance
Links Used
Fail-Over Modes
Full Redundancy
Partial Redundancy
Non-Redundancy
Page
Figure 2 Eight Frame Tribus System - Non-Redundant
Page
Debug Information
The Uploading Debug Information Status window appears
To find the file you just created, do the following
The AZedit debug file is made
2. Navigate to C\Telex\AZedit\Debug
Page
Installation
Installation and Configuration
To install the Tribus into an ADAM frame, do the following
Requirements
Configure each MCII-e Master Controller IP Address for the Ethernet
Configuration
To configure the IP Address for the MCII-e, do the following
1. Verify you are serially connected to AZedit
To configure the size of your frame, do the following
Configure the size of your Intercom system for each frame
The Intercom Configuration window appears
The Select Intercom Type window appears
3. Click Intercom Sizing Wizard
The Select Intercom Size window appears
6. Select the The number of frames in the intercom radio button
The Verify Intercom Configuration window appears
10. Select the Enable Test Audio recommended check box
The Select Frame Links window appears
15. Click Test to verify the configuration validity
The Intercom Configuration window reappears
16. Click Apply to apply the configuration to the intercom system
13. Click Finish
2. Click the Frame 2 IP Address 1 field
Configure the frame using the Frame Mapping window in AZedit
The field becomes active and a browse button appears
3. Click the browse button
Base 8 Port Number System
Base 8 vs. Base 16 Port Number Systems
installed
Base 16 Port Number System
To Force Autonomous Mode when no audio links are up, do the following
Force Autonomous Mode Check Box
The Intercom Configuration window appears
The Intercom Configuration window closes
AZedit Connections
Frame Mapping Table Window
Window Descriptions
Frame Column
CHAPTER
MAC Address 1 Column
IP Address 1 Column
IP Address 2 Column
MAC Address 2 Column
Move Up Button
Base 16 Column Check Box
Move Down Button
Accept Frame Mapping Table from Other Frames Check Box
Test Button
Select Frame Window
Done Button
IP Address 1 Column
MAC Address 1 Column
Cancel Button
IP Address 2 Column
MAC Address 2 Column
TBX Column
TBX Links Status Window
Comm Column
Example
A Partner Column
A Link Up/Dn Column
B Link Up/Dn Column
B Partner Column
Audio A Column
Intercom Alarms
Audio B Column
Audio C Column
The Intercom Alarms window appears
To open the Intercom Alarms window, do the following
Hiding and Clearing Alarms
Alarm Time Column
Frame Column
Resolved Time Column
Logging Window
Configure Logging Window
J9 Radio Button
J1 Radio Button
J10 Radio Button
Ethernet Radio Button
Download Firmware to the TBX-Tribus Card
Download Firmware Upgrades
CHAPTER
To download firmware to the TBX-Tribus card, do the following
The Download Device Firmware window appears
The Firmware Download window appears
7. Click Begin Download
The download begins. This takes a minute or two to occur
The success message and Download Device Firmware window closes
11. Verify the Tribus card firmware has been updated
