10-16 | Runco DTV-947 instruction

EYE-QTMAutoconvergence

In case of failures, the error message will shown: FAILED... Error 11; or

FAILED... Error 12; or FAILED... Error 13; or FAILED... Error 14; or FAILED... Error 15.

During the Sync Test, the following messages will displayed one after another on the screen:

Config for Sync;

Config for sync OK;

Horizontal Sync Test;

Horizontal Sync OK;

Vertical Sync Test;

Vertical Sync OK;

Frame and Field Test;

Frame and Field OK;

Sync Test OK.

In case of failures, the error message will be shown: FAILED... Error 21; or

FAILED... Error 22; or FAILED... Error 23; or FAILED... Error 24; or FAILED... Error 25; or FAILED... Error 26; or Sync Test Error 27 No syncs found

Check Camera & Cabling.

During the Ram Test, the following messages will displayed one after another on the screen:

Config for Ram;

Config for Ram OK;

Ram Data Line Test;

Ram Data Lines OK;

Ram Address Lines Test;

Ram Address Lines OK;

Ram Full Content Test;

Ram Full Content OK;

Ram Test OK

In case of failures, the error message will be shown:

FAILED... Error 31; or

FAILED... Error 32; or

FAILED... Error 33; or

FAILED... Error 34.

If all the tests are successful, the EYE-QTMmenu will be as follows:

Press the <EXIT> button to return to the EYE-QTM

TM

EYE-QDIAGNOSTICS

Interferance Test PASS

Generic Test	PASS
Sync Test	PASS
Ram Test	PASS

EYE-Q TM has been given

a clean bill of HEALTH.

When a “FAILED” message appears on the screen Please contact RUNCO INTERNATIONAL.

10-16

Image 66

Runco DTV-947 manual 10-16

Contents

DTV-947 Page Table of Contents Table of Contents 10-3 10-1Overview 10-1 10-4 10-15 11-1 On Safety Safety InstructionsInstallation Instructions OWNER’S Record On installation Mains lead Power cord with CEE 7 plugPower cord with Ansi 73.11 plug On servicing RS 232 Output Port Location and Function of ControlsRS 232 Input Port IR Sensor Sound controls Not used IR Transmission IndicatorHelp Not used For Future Use Switching On/Off AC Power mains Cord ConnectionPower Check Connections Connecting a Composite Video Source to the BNC video input Video input selection Connecting an S-Video or Video source to the S-Video input Input selection Rgbs or RGsB input selection Connecting a RGB Analog sourceConnecting a RGB Analog source with Tri-level sync RGB3S or RG3sB input selection Connecting a Component source Connecting a Component source with Tri-level syncYYB-YS or R-YYsB-Y input selection YYB-Y3S or R-YY3sB-Y input selection RS232 OUT Comm Port Remote Controlling Controlling Analog Picture Controls Pause key Start UP of the Adjustment Mode Adjustment mode Compose Random Access Adjustment Mode Starting up the random access adjustment modeOverview ‘Random Access Adjustment’ mode Selecting Setup Pattern Internal Cross Hatch Pattern Sync Fast/Slow Adjustment Random access adjustment mode selection menuPicture Tuning Color Balance Peaking Color SelectColor Select Phase Raster Shift Geometry AdjustmentsHorizontal Phase Adjustment Geometry Raster Shift Adjustment Left-Right east-west Adjustments Left Right E-W Top-Bottom north-south Adjustments TOP Bottom N-S Size Adjustment Vertical Linearity AdjustmentLinearity Blanking Adjustments Left blanking Top blanking Right blanking Bottom blanking Convergence Adjustment Coarse Convergence AdjustmentsConvergence Fine Convergence Adjustments Vertical corners Service Mode Starting up the Service modeOverview flowchart ‘Service’ mode Identification RuncoProjector Set-up Projector SET-UP Change password Total Run TimeChange Language Change baudrate Power up modeChange Projector Address Change Projector Address Memory Management Memory managementCopy a block Copy a Block Deletion of all blocks Deletion of blocksDeleting block by block Delete a Block All settings to midposition Undo all settings to midposConvergence mid Green convergence mid Common SettingsUndo R & B convergence mid Undo green convergence mid G2 Adjustment CRT run in cycleCRT RUN in Cycle Projector Warm UP Projector warm up Nal # pattern and restart the CRT run in optionExit returns to the Path Selection main menu Enter to select the projector warm up menu I2C Diagnostics 12C Diagnostics MESSAGES, WARNINGS, and Failures Messages, Warnings, and Failures Hardware Configuration RS-232 Control Sending a Record single instruction Command Code List Decimal values Sharpness $02,$00,$00,$51,$0A,$00,$00,$00,$01,$5C Quick Guide to using the EYE-QTMsystem Overview Easy-to-use, high precision automatic geometry system EYE-QTMAUTOCONVERGENCEEasy-to-use, high precision automatic convergence system Compact, built-in system Access to EYE-QTMON-SCREEN Menus EYE-QTMMENUEYE-QTMAutoconvergence EYE-QTMSETUP Setting the Configuration Focusing the Camera Lens Centering the Camera Centering the Camera Horizontally Centering the Camera Vertically TOUCH-UP on Source ON/OFFAppendix TOUCH-UP on Timer Adjusting Other SourcesReference Source Learning a Reference Learn Reference Adjusting Screen Size On Current Source TOUCH-UP Align on Current SourceAlign from Midposition on Current Source On ALL Sources TOUCH-UP on ALL SourcesAlign on ALL Sources Error Messages Align from Midposition on ALL SourcesInterrupting the Automatic Convergence Process No Pattern Error Status Reporting Forced BreakStatus Forced break EYE-Q 10-16 Specifications VHD Controller Manual Table of Contents Remarque Avertissement Safety Tips Features and Benefits General Description Front Panel Rear Panel Front and Rear Panel DescriptionsRGB Output Power Input LED Remote Control DescriptionDirect Access Buttons Program Button Video Input Connection ExamplesComposite Video Input Component Input Getting Started Quick SET-UP Guide Overall Functional Description Menu Description and Navigation Main Menu Picture Quality Adjustments Menu Description and Navigation Brightness TintColor Contrast Menu Description and Navigation Sharpness Luma EnhanceChroma Enhance Aspect Ratios First, the Basics Active image area Actual screen area Blanked cut off Areas Aspect Ratios Top Side RS-232 Protocol Ascii Specifications Supplied AccessoriesPage RUMA-003500 rev Tripaldi Way Hayward, CA