Runco, Projector Set-up, Identification | Runco DTV-947 manual

Service Mode

Projector Set-up

Highlight ‘Projector Set-Up’ by pushing the control disc up or down and press ENTER to display the projector set-up menu.

Within the projector set-up menu, the following items can be consolidated or set to the desired setting :

-Identification

-Total run time

-Change password

-Change language

-Change projector address

-Change baudrate

-Power up mode

Identification

Highlight ‘Identification’ with the control disc and press ENTER.

ENTER will start the selected item.

EXIT returns to the Service mode menu.

The ‘Identification’ screen gives information concerning :

-Projector address. To change the address of your projector, contact a qualified service technician.

-Software version.

-Configuration.

Possible installations :

*Front-ceiling

*Front-table

*Rear-ceiling

*Rear-table

-Baud rate PC : transfer speed for communication with an IBM PC (or com- patible) or MAC. The baud rate of the projector must be the same as the baud rate of the connected computer. When there is a difference, contact a qualified service technician to make the appropriate changes.

-Text ON/OFF

Indicates in operational mode if the bar scale and number indicator will be displayed and if warnings and failures will be displayed.

ON : displayed

OFF : not displayed

The status can be changed by pressing the ‘TEXT’ key once on the RCU.

-Serial no. : indicates the fabrication number of the projector. This number can be useful when calling for technical assistance.

SERVICE MODE

PROJECTOR SET-UP

MEMORY MANAGEMENT

COMMON SETTINGS

SERVICE MODE

PROJECTOR SET-UP

MEMORY MANAGEMENT

COMMON SETTINGS

12C DIAGNOSTICS

Select with or then <ENTER> <EXIT> to return.

PROJECTOR SET-UP

IDENTIFICATION

TOTAL RUN TIME

CHANGE PASSWORD

CHANGE LANGUAGE

CHANGE PROJECTOR ADDRESS

CHANGE BAUDRATE

POWER UP MODE: operating

RUNCO

DTV - 947

Proj. address : 001

Soft. Version : 6.00

Config. :Ceiling

Front

Baudrate PC : 9600

Text : ON

Serial No. : 103589552

7-2

Image 35

Runco DTV-947 manual Runco, Projector Set-up, Identification, Projector SET-UP

Contents

DTV-947 Page Table of Contents Table of Contents 10-4 10-1Overview 10-1 10-3 11-1 10-15 OWNER’S Record Safety InstructionsInstallation Instructions On Safety On servicing Mains lead Power cord with CEE 7 plugPower cord with Ansi 73.11 plug On installation IR Sensor Location and Function of ControlsRS 232 Input Port RS 232 Output Port For Future Use IR Transmission IndicatorHelp Not used Sound controls Not used Connections AC Power mains Cord ConnectionPower Check Switching On/Off Video input selection Connecting a Composite Video Source to the BNC video input Input selection Connecting an S-Video or Video source to the S-Video input RGB3S or RG3sB input selection Connecting a RGB Analog sourceConnecting a RGB Analog source with Tri-level sync Rgbs or RGsB input selection YYB-YS or R-YYsB-Y input selection Connecting a Component sourceConnecting a Component source with Tri-level sync RS232 OUT Comm Port Remote YYB-Y3S or R-YY3sB-Y input selection Controlling Controlling Pause key Analog Picture Controls Adjustment mode Start UP of the Adjustment Mode Compose Overview ‘Random Access Adjustment’ mode Random Access Adjustment ModeStarting up the random access adjustment mode Internal Cross Hatch Pattern Selecting Setup Pattern Color Balance Random access adjustment mode selection menuPicture Tuning Sync Fast/Slow Adjustment Color Select PeakingColor Select Geometry Geometry AdjustmentsHorizontal Phase Adjustment Phase Raster Shift Raster Shift Adjustment Left Right E-W Left-Right east-west Adjustments TOP Bottom N-S Top-Bottom north-south Adjustments Linearity Size AdjustmentVertical Linearity Adjustment Left blanking Top blanking Right blanking Bottom blanking Blanking Adjustments Convergence Convergence AdjustmentCoarse Convergence Adjustments Vertical corners Fine Convergence Adjustments Overview flowchart ‘Service’ mode Service ModeStarting up the Service mode Projector SET-UP RuncoProjector Set-up Identification Change Language Change passwordTotal Run Time Change Projector Address Power up modeChange Projector Address Change baudrate Copy a Block Memory managementCopy a block Memory Management Delete a Block Deletion of blocksDeleting block by block Deletion of all blocks Convergence mid All settings to midpositionUndo all settings to midpos Undo green convergence mid Common SettingsUndo R & B convergence mid Green convergence mid CRT RUN in Cycle Projector Warm UP G2 AdjustmentCRT run in cycle Enter to select the projector warm up menu Nal # pattern and restart the CRT run in optionExit returns to the Path Selection main menu Projector warm up 12C Diagnostics I2C Diagnostics MESSAGES, WARNINGS, and Failures Messages, Warnings, and Failures RS-232 Control Hardware Configuration Sending a Record single instruction Decimal values Command Code List $02,$00,$00,$51,$0A,$00,$00,$00,$01,$5C Sharpness Overview Quick Guide to using the EYE-QTMsystem Compact, built-in system EYE-QTMAUTOCONVERGENCEEasy-to-use, high precision automatic convergence system Easy-to-use, high precision automatic geometry system EYE-QTMAutoconvergence Access to EYE-QTMON-SCREEN MenusEYE-QTMMENU Setting the Configuration EYE-QTMSETUP Focusing the Camera Lens Centering the Camera Horizontally Centering the Camera Appendix Centering the Camera VerticallyTOUCH-UP on Source ON/OFF Reference Source TOUCH-UP on TimerAdjusting Other Sources Learn Reference Learning a Reference On Current Source Adjusting Screen Size Align from Midposition on Current Source TOUCH-UPAlign on Current Source Align on ALL Sources On ALL SourcesTOUCH-UP on ALL Sources Interrupting the Automatic Convergence Process Error MessagesAlign from Midposition on ALL Sources Status Forced break No Pattern ErrorStatus Reporting Forced Break EYE-Q 10-16 Specifications VHD Controller Manual Table of Contents Avertissement Remarque Safety Tips General Description Features and Benefits Front Panel RGB Output Rear PanelFront and Rear Panel Descriptions Power Input Program Button Remote Control DescriptionDirect Access Buttons LED Component Input Connection ExamplesComposite Video Input Video Input Quick SET-UP Guide Getting Started Overall Functional Description Main Menu Menu Description and Navigation Menu Description and Navigation Picture Quality Adjustments Contrast TintColor Brightness Chroma Enhance Menu Description and Navigation SharpnessLuma Enhance First, the Basics Aspect Ratios Aspect Ratios Active image area Actual screen area Blanked cut off Areas Side Top Ascii RS-232 Protocol Supplied Accessories SpecificationsPage RUMA-003500 rev Tripaldi Way Hayward, CA