Power Input | Runco DTV-947 manual

FRONT AND REAR PANEL DESCRIPTIONS

10.RS-232 Output

The output of this jack must be connected to the RS-232 input of the projector. This communication will allow the controller and projector to be turned on simultaneously by turning on just the controller.

11.Power Input

Plug in main power here.

12.115 VAC Fuse

This is the main AC input fuse.

(Main Fuse: 5mm x 20 mm, 500mA, 250v, Slow Blow)

13.Main Power Switch

Disconnects or applies main power to the processor.

11-9

Page 75

Image 75

Contents

DTV-947 Page Table of Contents Table of Contents 10-4 10-1Overview 10-1 10-3 11-1 10-15 OWNER’S Record Safety InstructionsInstallation Instructions On Safety On servicing Mains lead Power cord with CEE 7 plugPower cord with Ansi 73.11 plug On installation IR Sensor Location and Function of ControlsRS 232 Input Port RS 232 Output Port For Future Use IR Transmission IndicatorHelp Not used Sound controls Not used Connections AC Power mains Cord ConnectionPower Check Switching On/Off Video input selection Connecting a Composite Video Source to the BNC video input Input selection Connecting an S-Video or Video source to the S-Video input RGB3S or RG3sB input selection Connecting a RGB Analog sourceConnecting a RGB Analog source with Tri-level sync Rgbs or RGsB input selection Connecting a Component source Connecting a Component source with Tri-level syncYYB-YS or R-YYsB-Y input selection RS232 OUT Comm Port Remote YYB-Y3S or R-YY3sB-Y input selection Controlling Controlling Pause key Analog Picture Controls Adjustment mode Start UP of the Adjustment Mode Compose Random Access Adjustment Mode Starting up the random access adjustment modeOverview ‘Random Access Adjustment’ mode Internal Cross Hatch Pattern Selecting Setup Pattern Color Balance Random access adjustment mode selection menuPicture Tuning Sync Fast/Slow Adjustment Peaking Color SelectColor Select Geometry Geometry AdjustmentsHorizontal Phase Adjustment Phase Raster Shift Raster Shift Adjustment Left Right E-W Left-Right east-west Adjustments TOP Bottom N-S Top-Bottom north-south Adjustments Size Adjustment Vertical Linearity AdjustmentLinearity Left blanking Top blanking Right blanking Bottom blanking Blanking Adjustments Convergence Adjustment Coarse Convergence AdjustmentsConvergence Vertical corners Fine Convergence Adjustments Service Mode Starting up the Service modeOverview flowchart ‘Service’ mode Projector SET-UP RuncoProjector Set-up Identification Change password Total Run TimeChange Language Change Projector Address Power up modeChange Projector Address Change baudrate Copy a Block Memory managementCopy a block Memory Management Delete a Block Deletion of blocksDeleting block by block Deletion of all blocks All settings to midposition Undo all settings to midposConvergence mid Undo green convergence mid Common SettingsUndo R & B convergence mid Green convergence mid G2 Adjustment CRT run in cycleCRT RUN in Cycle Projector Warm UP Enter to select the projector warm up menu Nal # pattern and restart the CRT run in optionExit returns to the Path Selection main menu Projector warm up 12C Diagnostics I2C Diagnostics MESSAGES, WARNINGS, and Failures Messages, Warnings, and Failures RS-232 Control Hardware Configuration Sending a Record single instruction Decimal values Command Code List $02,$00,$00,$51,$0A,$00,$00,$00,$01,$5C Sharpness Overview Quick Guide to using the EYE-QTMsystem Compact, built-in system EYE-QTMAUTOCONVERGENCEEasy-to-use, high precision automatic convergence system Easy-to-use, high precision automatic geometry system Access to EYE-QTMON-SCREEN Menus EYE-QTMMENUEYE-QTMAutoconvergence Setting the Configuration EYE-QTMSETUP Focusing the Camera Lens Centering the Camera Horizontally Centering the Camera Centering the Camera Vertically TOUCH-UP on Source ON/OFFAppendix TOUCH-UP on Timer Adjusting Other SourcesReference Source Learn Reference Learning a Reference On Current Source Adjusting Screen Size TOUCH-UP Align on Current SourceAlign from Midposition on Current Source On ALL Sources TOUCH-UP on ALL SourcesAlign on ALL Sources Error Messages Align from Midposition on ALL SourcesInterrupting the Automatic Convergence Process No Pattern Error Status Reporting Forced BreakStatus Forced break EYE-Q 10-16 Specifications VHD Controller Manual Table of Contents Avertissement Remarque Safety Tips General Description Features and Benefits Front Panel Rear Panel Front and Rear Panel DescriptionsRGB Output Power Input Program Button Remote Control DescriptionDirect Access Buttons LED Component Input Connection ExamplesComposite Video Input Video Input Quick SET-UP Guide Getting Started Overall Functional Description Main Menu Menu Description and Navigation Menu Description and Navigation Picture Quality Adjustments Contrast TintColor Brightness Menu Description and Navigation Sharpness Luma EnhanceChroma Enhance First, the Basics Aspect Ratios Aspect Ratios Active image area Actual screen area Blanked cut off Areas Side Top Ascii RS-232 Protocol Supplied Accessories SpecificationsPage RUMA-003500 rev Tripaldi Way Hayward, CA

Runco DTV-947 manual Power Input

Models: DTV-947

FRONT AND REAR PANEL DESCRIPTIONS

10.RS-232 Output

11.Power Input