Assembly to Lens Motor, Carriage Plate CineWide | Runco VX-80d

Installation

3.12 Installing and Adjusting the CineWide Anamorphic Lens

If you are installing a CineWide-equipped projector, proceed as follows to install and adjust the anamorphic lens.

It is extremely important that the primary lens is properly

Note adjusted before you install the anamorphic lens. Ensure that the 16:9 or 4:3 image from the primary lens is perfectly centered on the screen.

	Attach Lens Mounting ➤	1.	Remove the two Z-Adjustment Levers and 1/4-20 Fiber Washers from the bottom of
	Assembly to Lens Motor		the lens mounting assembly.
	Carriage Plate (CineWide	2.	Place the Lens Mounting Assembly on top of (or under, if the projector is inverted) the
	with AutoScope) or Base	2.
	with AutoScope) or Base		Lens Motor Carriage Plate or Base Plate, so that the two threaded posts at the bottom
	Plate (fixed CineWide)
	Plate (fixed CineWide)		of the Z-Adjustment Plate pass through the corresponding slots on the carriage plate

			or base plate.
		3.	Secure the Lens Mounting Assembly to the plate with the Z-Adjustment Levers and
			Washers that you removed in Step 1.
			Note	If this is an AutoScope installation, leave enough space between
			Note	the projector and the lens mounting assembly to allow the lens to

move out of the light path without the assembly coming into contact with the projector front jewelry.

38	Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual

Image 50

Runco VX-80d manual Installing and Adjusting the CineWide Anamorphic Lens, Assembly to Lens Motor, Carriage Plate CineWide

Contents

VX-40d / VX-50d VX-60d / VX-80d Page TWO Year Limited Warranty For Projectors, Video Processors and Controllers Effective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Install Projector Stand CineWide with AutoScope, Floor-Mount Operation Maintenance and TroubleshootingSpecifications Serial Communications Table of Contents List of Figures Xii About This Manual Significance. They also provide supplemental information Using This ManualCertain features Degrade performance or cause a malfunction Description, Features and Benefits Optional Accessories Runco VX-40d/-50d/-60d/ -80d at a Glance VX-40d/-50d/-60d/-80d Top/Rear/Front View Rear Foot Stationary Power Input 100 to 240 VAC VX-40d/-50d/-60d/ -80d Input Panel Input 3 Video / Input 4 S-Video RS232RS232 OUT Not used RS422 Not used Gpio Not used Input 2 DVI Zoom VX-40d/-50d/-60d/ -80d Rear-Panel KeypadFocus VX-40d/-50d/-60d/-80d has its own internal menu system Help Menu Navigation ButtonsInput 1 BNC Exit DHD Controller Front Panel DHD Controller Front Panel DHD Controller Rear Panel Outputs Inputs 3. DVI 1 / DVI 2 Digital HD1 / HD2 Analog BNC connectorsComponent Video RCA connectors Video 1 / S-VIDEO Remote Control DHD Controller For more information about aspect ratios, refer to Table On / OFFCursor Buttons Video ANA Anamorphic Memory Preset Buttons ISF NT NightAspect Ratio Selection Buttons 4X3 Standard 43 Controls and Functions Installation Installation specialist Quick SetupInstallation Overview Step Procedure For Details, Refer to Installation Type Installation ConsiderationsProjector Installation Options Ambient Light Lens Option Note Throw Dist VX-40d/-50d Lens Options and Throw RatiosThrow Ratio Throw Distance Range Minimum Maximum VX-60d/-80d Lens Options and Throw Ratios Lens Option Note Throw Dist Screen Width Minimum Maximum Vertical and Horizontal Position Horizontal Lens Shift Screen center are aligned with each other Folded Optics Installing the Projection Lens Lens Assembly Front View Fixed CineWide Are both fully assembled Installing the Optional CineWide Lens MountAutoScope or Base Plate AutoScope stand used for floor-mounted projector Floor Mounting Adjusting the ProjectionMounting VX-40d/-50d/-60d/ -80d Ceiling Mounting Connector Panel Access Connecting the DHD Controller to VX-40d/-50d/-60d/-80d Connecting Source Digital DTV RGB or Component Video Connections See Figure 10. Digital DTV RGB or Component Video Connections Analog Computer RGB Connections See Figure 11. Analog RGB Connections Composite/S-Video/Component Video Connections See Figure 12. Composite, S-Video and Component Video Connections Connection Connecting 12-VoltRS-232 Controller Trigger Outputs to Connecting to AC Power Input voltage to the AutoScope lens motor must be between Selecting the Input Source Turning on the PowerYou must enter a passcode to access the Service menu Adjusting the Picture Orientation Primary Lens Adjustments Focus Zoom Vertical and Horizontal Lens Shift Carriage Plate CineWide Installing and Adjusting the CineWide Anamorphic LensAssembly to Lens Motor With AutoScope or Base Horizontal Position X Adjustment Too Low Correct position Too High Wrong Position Correct Position Geometry Calibrating Projector Inputs Main TheaterMaster Remote 1. Power Button Control Functions Navigating the Projector Menus Are disabledChannel Setup 17. Copying a Channel Auto Setup You cannot use Auto Setup with a locked channel. Copy 18. Resize Presets No Resizing Native aspect ratio is with the primary lens only. With an Installation Recommended see below Adjust Pixel Tracking before Pixel PhaseValues shown represent where the approximate center On an internal grayscale test pattern Input Levels are not applicable to DVI InputExperienced technicians use the Input Levels submenu There must be at least two consecutive white pixels present Uncheck this item before exiting this menu Working With the Lamp Originally expected may no longer be possible Intensity value is not the actual lumen output, but rather a More easily maintained as the lamp ages Installation Using the On-Screen Menus Operation Input Source ISF PresetsService Aspect Ratio Aspect Ratio Main MenuInput Source HD Pass Thru 1 HD Pass Thru Aspect Ratio Settings Remote Aspect Ratio Control Description Key Picture Picture Brightness Contrast Color Tint Sharpness Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Left/Right Up/Down Width Height Overscan ResolutionInput Position Information ISF PresetsISF Presets ISF Night ISF Day Custom Save Factory Default Serial Number Hardware Firmware 0002.003A Date Mar 15 You must enter a passcode to access the Calibration menu Calibration Operation Service Input Names Restore Composite Video Component SD Tip Auto ADC Bandwidth Auto YPbPr Input ResolutionHD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV Operation Lamp and Filter Replacement Removing the Lamp Door Removing the Lamp Recording the Serial Number of a New Lamp Lamp is accurate Lens Replacement Removing the Primary Lens Symptom Possible Causes Solution Troubleshooting TipsTroubleshooting Chart Power down the projector Code Description General VX-40d/-50d/-60d/-80d Error CodesError Codes Power and Cooling Code Description Lamp Failures Panel Driver and Formatter Code Description Tipm Image ProcessorBuilt-In Keypad Code Description Miscellaneous Serial Commands RS-232 Connection and Port ConfigurationSerial Command Syntax Command Aspect Ratio Commands VIRTUAL235 YES Image Preset Commands Value Description Min/max Stored? Input Position Commands Output Shift Commands Bkgnd Serial Communications VX-40d/-50d/-60d/ -80d Specifications VX-40d/-50d/-60d/-80d Specifications Power Requirements VX-40d/-60d Home Theater Calibration SpecificationsIndustry-Standard Specifications VX-50d/-80d Limited Warranty DimensionsWeight without lens Specifications are subject to change without notice DHD Controller Specifications DHD Controller Specifications VX-40d/-50d/-60d/ -80d Dimensions VX-40d/-50d/-60d/-80d Dimensions Specifications Page Runco CL-810 Owner’s Operating Manual