Code Description Lamp Failures, Power and Cooling | Runco VX-40d

Maintenance and Troubleshooting

Table 5-2. VX-40d/-50d/-60d/-80d Error Codes (continued)

Code	Description

	Lamp Failures

20	Lamp turned on unexpectedly (fault related to ballast).

21	Lamp airflow low, overheating imminent.

23	Cannot read valid ballast ID.

26	Lamp 1 Interlock: lamp door open, lamp not installed.

27	Can’t turn lamp on.

28	Lamp turned off unexpectedly.

29	Lamp ballast overheated.

	Power and Cooling

46	Red DMD heat sink overheated.

47	Green DMD heat sink overheated.

48	Blue DMD heat sink overheated.

49	Prism overheated.

4C	Projector shutdown due to critical error.

C0	Lamp blower failure (lamp not turned on).

51	LVPS fan failed (Fan 1).

52	LVPS/Red cooling fan failed (Fan 2).

53	DC lamp fan failed (VX-40d or VX-60d; Fan 3).

54	Red DMD heatsink fan failed (Fan 4).

55	Green DMD heatsink fan failed (Fan 5).

56	Blue DMD heatsink fan failed (Fan 6).

57	TIPM fan failed (Fan 7).

58	TIPM fan failed (Fan 8).

Note: To clear a system error, press the EXIT key (on the projector’s rear-panel keypad) twice. If necessary, reset the projector by powering it off, allowing it to cool and powering it on again. Contact your Runco dealer or Runco technical support if the error persists.

80	Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual

Image 92

Runco VX-40d, VX-50d, VX-80d, VX-60d manual Code Description Lamp Failures, Power and Cooling

Contents

VX-40d / VX-50d VX-60d / VX-80d Page TWO Year Limited Warranty For Projectors, Video Processors and Controllers Effective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Install Projector Stand CineWide with AutoScope, Floor-Mount Maintenance and Troubleshooting SpecificationsOperation Serial Communications Table of Contents List of Figures Xii About This Manual Using This Manual Certain featuresSignificance. They also provide supplemental information Degrade performance or cause a malfunction Description, Features and Benefits Optional Accessories Runco VX-40d/-50d/-60d/ -80d at a Glance VX-40d/-50d/-60d/-80d Top/Rear/Front View Rear Foot Stationary Power Input 100 to 240 VAC VX-40d/-50d/-60d/ -80d Input Panel RS232 RS232 OUT Not used RS422 Not used Gpio Not usedInput 3 Video / Input 4 S-Video Input 2 DVI VX-40d/-50d/-60d/ -80d Rear-Panel Keypad FocusZoom VX-40d/-50d/-60d/-80d has its own internal menu system Menu Navigation Buttons Input 1 BNCHelp Exit DHD Controller Front Panel DHD Controller Front Panel DHD Controller Rear Panel Outputs HD1 / HD2 Analog BNC connectors Component Video RCA connectorsInputs 3. DVI 1 / DVI 2 Digital Video 1 / S-VIDEO Remote Control DHD Controller On / OFF Cursor ButtonsFor more information about aspect ratios, refer to Table Video Memory Preset Buttons ISF NT Night Aspect Ratio Selection ButtonsANA Anamorphic 4X3 Standard 43 Controls and Functions Installation Quick Setup Installation OverviewInstallation specialist Step Procedure For Details, Refer to Installation Considerations Projector Installation OptionsInstallation Type Ambient Light VX-40d/-50d Lens Options and Throw Ratios Throw Ratio Throw Distance RangeLens Option Note Throw Dist Minimum Maximum VX-60d/-80d Lens Options and Throw Ratios Lens Option Note Throw Dist Screen Width Minimum Maximum Vertical and Horizontal Position Horizontal Lens Shift Screen center are aligned with each other Folded Optics Installing the Projection Lens Lens Assembly Front View Fixed CineWide Are both fully assembled Installing the Optional CineWide Lens MountAutoScope or Base Plate AutoScope stand used for floor-mounted projector Adjusting the Projection Mounting VX-40d/-50d/-60d/ -80dFloor Mounting Ceiling Mounting Connector Panel Access Connecting the DHD Controller to VX-40d/-50d/-60d/-80d Connecting Source Digital DTV RGB or Component Video Connections See Figure 10. Digital DTV RGB or Component Video Connections Analog Computer RGB Connections See Figure 11. Analog RGB Connections Composite/S-Video/Component Video Connections See Figure 12. Composite, S-Video and Component Video Connections Connecting 12-Volt RS-232 ControllerConnection Trigger Outputs to Connecting to AC Power Input voltage to the AutoScope lens motor must be between Selecting the Input Source Turning on the PowerYou must enter a passcode to access the Service menu Adjusting the Picture Orientation Primary Lens Adjustments Focus Zoom Vertical and Horizontal Lens Shift Installing and Adjusting the CineWide Anamorphic Lens Assembly to Lens MotorCarriage Plate CineWide With AutoScope or Base Horizontal Position X Adjustment Too Low Correct position Too High Wrong Position Correct Position Geometry Calibrating Projector Inputs Main TheaterMaster Remote 1. Power Button Control Functions Navigating the Projector Menus Are disabledChannel Setup 17. Copying a Channel Auto Setup You cannot use Auto Setup with a locked channel. Copy 18. Resize Presets No Resizing Native aspect ratio is with the primary lens only. With an Installation Recommended see below Adjust Pixel Tracking before Pixel PhaseValues shown represent where the approximate center On an internal grayscale test pattern Input Levels are not applicable to DVI InputExperienced technicians use the Input Levels submenu There must be at least two consecutive white pixels present Uncheck this item before exiting this menu Working With the Lamp Originally expected may no longer be possible Intensity value is not the actual lumen output, but rather a More easily maintained as the lamp ages Installation Using the On-Screen Menus Operation ISF Presets ServiceInput Source Aspect Ratio Main Menu Input SourceAspect Ratio HD Pass Thru 1 HD Pass Thru Aspect Ratio Settings Remote Aspect Ratio Control Description Key Picture Picture Brightness Contrast Color Tint Sharpness Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Left/Right Up/Down Width Height Overscan ResolutionInput Position ISF Presets ISF Presets ISF Night ISF Day Custom Save Factory DefaultInformation Serial Number Hardware Firmware 0002.003A Date Mar 15 You must enter a passcode to access the Calibration menu Calibration Operation Service Input Names Restore Composite Video Component SD Tip Auto ADC Bandwidth Auto YPbPr Input ResolutionHD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV Operation Lamp and Filter Replacement Removing the Lamp Door Removing the Lamp Recording the Serial Number of a New Lamp Lamp is accurate Lens Replacement Removing the Primary Lens Symptom Possible Causes Solution Troubleshooting TipsTroubleshooting Chart Power down the projector Code Description General VX-40d/-50d/-60d/-80d Error CodesError Codes Power and Cooling Code Description Lamp Failures Panel Driver and Formatter Code Description Tipm Image ProcessorBuilt-In Keypad Code Description Miscellaneous RS-232 Connection and Port Configuration Serial Command SyntaxSerial Commands Command Aspect Ratio Commands VIRTUAL235 YES Image Preset Commands Value Description Min/max Stored? Input Position Commands Output Shift Commands Bkgnd Serial Communications VX-40d/-50d/-60d/ -80d Specifications VX-40d/-50d/-60d/-80d Specifications Home Theater Calibration Specifications Industry-Standard SpecificationsPower Requirements VX-40d/-60d VX-50d/-80d Dimensions Weight without lensLimited Warranty Specifications are subject to change without notice DHD Controller Specifications DHD Controller Specifications VX-40d/-50d/-60d/ -80d Dimensions VX-40d/-50d/-60d/-80d Dimensions Specifications Page Runco CL-810 Owner’s Operating Manual