Remounting

Grasp the sections near the front panel arms on both sides, and hold the front panel so that it is nearly horizontal. Push the arm shafts towards the outside so that they come into contact with the top of the indentations on the right and left sides of the air conditioner. Then push firmly until the arm shafts click into place. After closing the front panel, press firmly on the parts indicated by the arrows to securely fasten the panel in place.

Also refer to the figure that shows “How to replace the anti-mold filter”.

Trouble

Possible Cause

Remedy

 

 

 

Clicking sound is

In heating or cooling

This is normal, and

heard from the air

operation, any plastic

the sound will soon

conditioner.

parts may expand or

disappear.

 

shrink due to a

 

 

sudden temperature

 

 

change. In this event,

 

 

a clicking sound may

 

 

occur.

 

CAUTION

When using a footstool or the like, be careful not to let it tip over.

OPERATION lamp

The use of cellular

1. Turn off the power

lights but outdoor unit

phones near the air

then restart the air

will not run.

conditioner may

conditioner after a

 

cause disturbance to

while.

Washing the front panel with water

Clean the front panel gently using a soft sponge, or the like. Then wipe away any remaining moisture.

Neutral detergent may be used to remove stubborn dirt. Then rinse thoroughly with water and wipe away any remaining moisture.

TROUBLESHOOTING

If your air conditioner does not work properly, first check the following points before requesting service. If it still does not work properly, contact your dealer or service center.

Trouble

 

Possible Cause

 

Remedy

 

 

 

 

Air conditioner does

1. Power failure.

1.

Restore power.

not run at all.

2.

Leakage circuit

2.

Contact service

 

 

 

breaker tripped.

 

center.

 

3.

Line voltage is too

3.

Consult your

 

 

low.

 

electrician or

 

 

 

 

dealer.

 

4.

Batteries in remote

4.

Replace batteries.

 

 

control unit have

 

 

 

 

run down.

 

 

 

 

 

OPERATION lamp

Trouble in system.

Contact service

blinks and air

 

 

center.

conditioner does not

 

 

 

 

operate.

 

 

 

 

 

 

 

Compressor runs but

Obstruction in front of

Remove obstruction.

soon stops.

condenser coil.

 

 

 

 

 

 

Poor cooling (or

1. Dirty or clogged air

1.

Clean air filter to

heating)

 

filter.

 

improve airflow.

performance.

2.

Heat source or

2.

Eliminate heat

 

 

 

many people in

 

source if possible.

 

 

room.

 

 

 

3.

Doors and/or

3.

Shut them to keep

 

 

windows are open.

 

the heat (or cold)

 

 

 

 

out.

 

4.

Obstacle near air

4.

Remove it to

 

 

intake or air

 

ensure good

 

 

discharge port.

 

airflow.

 

5.

Thermostat is set

5.

Set the

 

 

too high for cooling

 

temperature lower

 

 

(or too low for

 

(or higher).

 

 

heating).

 

 

 

6.

(Outdoor

6.

(Consult your

 

 

temperature is too

 

dealer or try to use

 

 

low for heating.)

 

another heat

 

 

 

 

appliance.)

 

 

 

 

 

its normal operation.

2. Consult your

dealer.

OPERATING RANGE

The air conditioner is operable within the temperature ranges as listed below:

 

Temperature

Indoor air

Outdoor air

 

 

temperature

temperature

 

 

 

 

 

COOLING

Max.

95

°F DB /

115 °F DB

 

 

71

°F WB

 

 

 

 

 

 

 

 

Min.

67

°F DB /

0 °F DB

 

 

57

°F WB

 

 

 

 

 

 

 

 

HEATING

Max.

80

°F DB /

75

°F DB /

 

 

67

°F WB

65

°F WB

 

 

 

 

 

Min.

– DB / – WB

– DB / 0 °F WB

 

 

 

 

 

 

WIRED REMOTE CONTROLLER

Aseparately sold wired remote controller (STK-RCS- 7TWSUA) used with this air conditioner is also available. If you wish to use the wired remote control function, you will need to purchase both the optional wired remote controller and its connection kit (STK-KCW2).

OI-149-17-EG

17

 

Page 77
Image 77
Sanyo CH3682, CH3082 Troubleshooting, Operating Range, Wired Remote Controller, Washing the front panel with water