Manuals / Brands / TV and Video / DVR / Sanyo / TV and Video / DVR

Sanyo DSR-5709P (5) MODE, (4) LEVEL, (3) Time period, (1)Motion sensor setting, (2) Camera number display

1 236

Download 236 pages, 6.19 Mb

2RECORD SET

Setting the motion sensors

Use the following procedure to set motion sensors on video from each camera so that alarms can be detected.

(1)

(2)CH01 T-1 LEVEL : OFF MODE : A

(3)(4) (5)

(1)Motion sensor setting

Display changes in response to the sensor condition. Settings are made using the jog dial.

-: Sensor off

A or B: Sensor on

(2) Camera number display

Changes when a [CAMERA SELECT] button is pressed. Use this item to select the camera for which motion sensors are to be set up.

(3) Time period

Select an interval set using “TIME PERIOD” (JP.74).

(4) LEVEL

Sets the sensitivity level of the motion sensors. OFF: No motion sensor has been set.

1 to 10: A motion sensor is set. Lower values correspond to higher sensitivity levels and vice versa.

3 Turn the jog dial to select “2.RECORD SET” and then turn the shuttle dial clockwise.

The <RECORD SET> screen is displayed.

4 Turn the jog dial to select “7.ALARM REC MODE SET” and then turn the shuttle dial clockwise.

The <ALARM REC MODE SET> screen is displayed.

<ALARM REC MODE	SET>
ALARM RECORDING	: OFF
PICTURE QUALITY	: ENHANCED
PICTURE QUALITY SET	->
AUDIO RECORDING	: OFF
ALARM INTERLEAVE	: ONLY
REC RATE: 12.5FPS, DURATION: 20SEC
PRE-ALARM RECORDING	: ***
REC RATE: ***** FPS,	DURATION: *****
ALARM TRIGGER	: SENSOR
MOTION SENSOR	->

5 Turn the jog dial to select “MOTION SENSOR” and then turn the shuttle dial clockwise.

(5) MODE

Sets the detection method for the motion sensors. (JP.107)

1 Make timer settings for “TIME PERIOD A” and “TIME PERIOD B” on the <TIME PERIOD SET> screen. (JP.74)

2 Press the [MENU] button.

The MENU indicator lights up and the <MAIN MENU> is displayed.

MENU

The <MOTION SENSOR> screen is displayed.

The cursor (reverse highlighting) is displayed at the top left position. Cursor can be moved to the left and right using the jog dial if a mark indicating such actions is displayed in the upper right of the screen.

<ALARM REC MODE

SET>

ALARM RECORDING

: ENABLED

PICTURE QUALITY

: ENHANCED

PICTURE QUALITY SET

->

AUDIO RECORDING

: OFF

ALARM INTERLEAVE

: ONLY

REC RATE: 12.5FPS, DURATION: 20SEC

PRE-ALARM RECORDING

: OFF

REC RATE: ***** FPS,

DURATION: *****

ALARM TRIGGER

: SENSOR

MOTION SENSOR

->

CH01 T-1 LEVEL : OFF MODE : A

English

105

Contents

Before installing and using this unit, please read this manual carefully Be sure to keep it handy for later reference PRECAUTION WARNING: Please note: INTRODUCTION CONTENTS 1 BEFORE USE Notes on handling the internal HDD The HDD and cooling fan are consumable Connecting RS-485control terminals Setting the motion sensors Setting alarm operation and display GENERAL SET Setting for control terminal output Hard disk initialization and mirroring The various ways of displaying Performing operations in play mode Adjusting the image and audio Downloading live images to a PC 3. ALARM THUMBNAIL SEARCH Before Using DVR Viewer2 Structure of the Screen and the Function of each Switching the Display Pattern Selecting the Channel Displayed Functions of the Viewer Operating Panel 1BEFORE USE zLamp off: Normal operation zFast flashing: Abnormal condition of hard disk zSlow flashing: Abnormal condition of cooling fan „Replacement time of main components or parts 2NAMES AND FUNCTIONS OF PARTS 14.[EXIT/OSD] button and indicator z EXIT: 15.[PLAY/STOP] button and indicator (JP.32) 16. [ZOOM] button and indicator (JP.33) 17. [SEARCH] button and indicator (JP.38) 18. [STILL] button and indicator (JP.34) 1.Optional board slot 2.VIDEO IN terminals Connects to video cameras 3.VIDEO OUT terminals 4.ALARM IN terminals (1 to 16) 5.SENSOR ALARM OUT terminals 6.Control terminals 7.[ALL RESET] button 8.USB terminal LAN terminal 10.AUDIO IN terminal 3INSTALLATION AND CONNECTIONS RJ-11Pin locations Connection Cable types RS-485termination switch settings Operation 1 Connect as above 3 Operate the dome cameras with the front panel buttons. (JP.153) LAN connection Internet connection Page 1PREPARING FOR USE 1 Press the [EXIT/OSD] button 1 Press the [MENU] button 4 Turn the shuttle dial clockwise 6 Press the [EXIT/OSD] button Example: Setting 8:30 on 26 January 4 Turn the jog dial to select “01” and then turn the shuttle dial clockwise 5 Turn the jog dial to select “26” and then turn the shuttle dial clockwise 7 Press the [EXIT/OSD] button Hard disk recording areas [A]Recording area 2MONITORING VIDEO FROM A CAMERA 4 Press the [ZOOM] button to return to normal magnification 1 Press the [QUAD] button 2 To view video from other cameras, press the [QUAD] button again 3 To return to full screen display, press a [CAMERA SELECT] button 1 Press the [MULTI] button 2 To return to full screen display, press a [CAMERA SELECT] button Example: Enlarging video during multi 9 screen display 1 Press the [PLUS] button during multi 9 screen display 2 Press a [CAMERA SELECT] button Setting automatic full screen selection 1 Press the [SEQUENCE] button 2 Press the [SEQUENCE] button to end automatic selection Setting automatic quad-screenselection 2 Press the [SEQUENCE] button 1 Press the [MON2] button Viewing on a full screen 2 Press the No. 4 [CAMERA SELECT] button Viewing on a quad screen 2 Press the [QUAD] button 3 Press the [SEQUENCE] button 4 Press the [SEQUENCE] or [QUAD] button to return to normal quad-screendisplay Displaying alarm video in full screen format 3 Press the [MON2] button to end the monitor 2 setting procedure 3RECORDING 1 Set alarm recording. (JP.98) 2 When an alarm signal is detected 3 End alarm recording 1 Set pre-alarmrecording. (JP.102) 2 If an alarm is detected 1 Press the [MARK/COPY] button while recording video 4PLAY (3)Returning to normal playback Using reverse playback, fast-rewind,and reverse-slowplayback (1) Performing reverse playback (2) Performing fast-rewindplayback (3) Performing reverse-slowplayback (4) Returning to normal playback 1 Press the [STILL] button during playback 2 Press the [STILL] button again to resume normal playback 1 Turn the jog dial while playback is paused 1 Press the [MARK/COPY] button during playback on a full screen Playing video on quad screens 1 Press the [QUAD] button during playback Playing video on multi 9 or multi 16 screens 1 Press the [MULTI] button during playback Playing enlarged video 5 Press the [PLUS] button to return to the screen from before enlarging video Using flash playback 1 Play video from the camera you want to view using flash playback, on a full screen 5SEARCHING FOR RECORDED VIDEO (7)BOOKMARK SEARCH (JP.42) Page 3 Turn the jog dial to select the video for playback from the list To display the next or previous recording Entering an alarm number to search for an alarm video 1 In the search screen, press the [FUNC.] button and select “SEARCH” 2 Turn the shuttle dial clockwise 5 Press the [FUNC.] button Entering a camera number to search for an alarm video 3 Press the [CAMERA SELECT] button for the camera number to search 4 Press the [FUNC.] button To view alarm video before or after the current playback 1 Press the [ALARM] button during playback 3 Turn the jog dial to select the video for playback Search by entering an alarm number 1 In the search screen, press the [FUNC.] button 3 Select alarm number by turning the jog dial and shuttle dial Search by entering a camera number Example: To search for a recording from camera 5 from 8:30 pm on 26 October (1) RECORDING TOP: (2) RECORDING END: (3) CHANNEL: 3 Turn the shuttle dial clockwise while “CHANNEL” is selected 4 Press the [CAMERA SELECT] 5 button The cursor moves to “DATE TIME” 5 Specify the date and time (1)Turn the shuttle dial clockwise and turn the jog dial to “26” (day) Page Entering an archive number to search for an alarm video 3 Turn the jog dial and shuttle dial to select an archive number 5 Press a [CAMERA SELECT] button and then turn the shuttle dial clockwise Setting the motion sensor for searching 5 Turn the shuttle dial clockwise Page Page 6SAVING (COPYING) RECORDED VIDEO Play video to be copied Example: Copying 10 seconds of video 2 Press the [STILL] button when the frame to be copied is displayed 3 Press the [MARK/COPY] button 4 Turn the jog dial clockwise 8 Specify the channel to copy 9 Turn the shuttle dial clockwise „To cancel copying Example: Copying 20 images 1 Insert a USB memory 4 Press the [MARK/COPY] button 8 Turn the shuttle dial clockwise while “PICTURES” is flashing 10 Turn the jog dial to select “20” and then turn the shuttle dial clockwise 11 Specify the channel to copy 12 Turn the shuttle dial clockwise 13 Turn the shuttle dial clockwise Play video to be copied on a full screen Example: Copying the maximum video to the copy destination 1 Connect a recordable CD or DVD drive and insert a disc 9 Specify the channel to copy 10 Turn the shuttle dial clockwise 11 Turn the shuttle dial clockwise Drive: OS: 14 Specify the disc validation function settings 15 Turn the shuttle dial clockwise Copying data onto multiple discs 1st disc 2nd disc 650MB Formatting a USB memory, CD-RWor DVD+RW 1 Insert a USB memory, CD-RWor DVD+RW 2 Press the [MARK/COPY] button Folder hierarchy for data copied onto a USB memory Folder hierarchy for data copied onto a CD-R/RW or DVD+R/RW MENU CONFIGURATION AND OPERATIONS Movement and confirmation in sub-menusand setting screens 1 Open the menu screen containing the items to be returned to default settings 2 Press the [MENU RESET] button Suspending video recording To suspend video recording: Page 1INITIAL SET 4 Turn the jog dial to select “MODE” under <SUMMER TIME SET 6 Turn the jog dial to select “USE” and then turn the shuttle dial clockwise 7 Set the date and time Example: Set the summer time to begin at 25 March, 2007, 02:00 Set the summer time to end 28 October, 2007, 02:00 MONTH Summer time begins 8 Use the same procedure to set the time on the second recorder 4 Turn the jog dial to select “YES” and then turn the shuttle dial clockwise 4 Press the No. 3 [CAMERA SELECT] button 6 Turn the jog dial to select “H” 8 Repeat the above steps to enter the remaining characters 9 Press [EXIT/OSD] button after all digits are set Example: Setting 26 October as a holiday 4 Set the day and month for item 5 Use the same procedure to set other holidays „Morning to lunchtime: 6:00 to 11:00 „Lunchtime: 11:00 to 13:00 „Lunchtime to evening: 13:00 to 20:00 Operations during the specified time periods „Setting automatic selection of camera video „Masking camera video using a gray pattern „Alarm recording using motion sensors Timer period settings Example 1: Setting periods using TIME PERIOD A and zTIME PERIOD A T-1=6:00 T-2=11:30 T-3=13:30 T-4=18:00 zTIME PERIOD B T-1=6:00 T-2=8:00 T-3=14:30 T-4=20:00 5 Set the time for T-1 Timer period operations settings Motion sensing for “TIME PERIOD B” 11 Press the [EXIT/OSD] button 2RECORD SET Setting based on recording days 9 Set the time for timer recording Example: Timer recording from 8 AM to 8 PM 14 Turn the shuttle dial counter-clockwise 15 Turn the jog dial to select “YES” and then turn the shuttle dial clockwise 16 Press the [EXIT/OSD] button Setting based on recording rate Page Page Page „Default hard disk settings „Recording area allocations Example: Setting the recording area to 50% 6 Turn the jog dial to select “YES” 5 Turn the jog dial to select “YES” and then turn the shuttle dial clockwise Page 01-01-0700:00:00 REC 5% EN A ALARM Use the following procedure to set the storage period for recorded data When the set period has expired, the corresponding data cannot be played back Page „Setting the picture quality for each camera 8 Turn the shuttle dial clockwise 12 Press the [EXIT/OSD] button (1) PROGRAM (2) SELECT INDIVIDUAL CAMERA RATE The <PROGRAM REC SET> screen is displayed “P-1”flashes for “PROGRAM” The cursor moves to “01” under “SELECT INDIVIDUAL CAMERA RATE (FPS)” 7 Turn the jog dial to select “5” and then turn the shuttle dial clockwise Camera No. 1 is now set to record at a rate of 5. The cursor moves to “02” Timer setting items (1) WEEK (2) START (3) STOP (4) PROGRAM 5 Turn the jog dial to set the day, and turn the shuttle dial clockwise 6 Setting the “START” and “STOP” time Example: Setting a start time of 6:30 PM and an end time of 11:15 PM 10 Use the same procedure to set other items „To change a setting item To cancel all set timer reservations 4 Press the [MENU RESET] button OFF 12.5 FPS OFF 20:30 OFF 5FPS Timer recording using an external timer Example: Recording at a rate of 5 FPS using the EXT TIMER IN terminal 5FPS OFF To set alarm recording Page “ONLY” flashes The cursor moves to “REC RATE/DURATION” ‹ONLY Video is recorded only from cameras with an alarm occurring 14 Turn the shuttle dial clockwise To set pre-alarmrecording 5 Turn the jog dial to select “ON” and then turn the shuttle dial clockwise Page Setting alarm triggers Page 6 Press a [CAMERA SELECT] button 8 Turn the jog dial to select “A” or “B” 9 Turn the shuttle dial clockwise twice 10 Use the same procedure to set other sensor positions „To specify the start position and end position together within a range Setting sensitivity levels The cursor moves to “MODE” Motion sensing is disabled Motion sensing is enabled. Lower numbers correspond to higher levels of sensitivity „To stop motion sensor recording Page Page 3GENERAL SET 2 Turn the jog dial to select “3.GENERAL SET” and then turn the shuttle dial clockwise (8) (3)(4) 6 Use the same procedure to set the other items to “ON” or “OFF” Page (1)ALARM (default setting: OFF) Sounds a buzzer when an alarm occurs (2)DISK FULL (default setting: ON) (3) DISK ERROR (default setting: ON) (4) LOCK WARNING (default setting: ON) (5)KEY IN (default setting: OFF) Sounds a buzzer when a button is pressed Page Page 13 Press the [EXIT/OSD] button Setting user ID „User level and privileges Registering a user 6 Enter a user ID 8 Enter a password 10 Use the same procedure to register other users Turning on the key lock, password lock and network lock [SHUTTLE HOLD] button 2 Confirm the lock status Canceling the key lock 1 During key lock, press the [SHUTTLE HOLD] button for approximately 3 seconds Canceling the password lock or network lock Example: While password lock is activated Page Page Initializing the hard disk 4 Then turn the shuttle dial clockwise Setting mirroring 9 Turn the jog dial to select “YES” and then turn the shuttle dial clockwise 10 Press the [EXIT/OSD] button Switching playback disks Making network connections Making network settings 6 Set “IP ADDRESS” 7 Set “SUBNET MASK” 8 Set “GATEWAY” 9 Set “PORT” 16 Turn the shuttle dial counter-clockwise 19 Press the [EXIT/OSD] button Page Page „User levels and privileges Setting user 4SCREEN SET 7 Turn the jog dial to select “05” and then turn the shuttle dial clockwise 8 To render a certain channel unspecified: Checking modified screen positions 5 Use the same operation to set the switching interval for quad screen display Setting the time period to switch the display on the main monitor and monitor Set the main monitor and monitor 2 display period for each camera The <MAIN/MON.2 MONITOR SET> screen is displayed “T-1”flash for “TIME PERIOD” The cursor moves to “1S” for “01” and “MAIN MON.” ‹ T-1 11 Use the same procedure to set other channels 4 Turn the jog dial to select “MASK” and then turn the shuttle dial clockwise Page Page 5POWER LOSS/USED TIME 6INITIALIZATION LOG 7COPY MENU SETTINGS 6 Turn the jog dial to select “YES” and then turn the shuttle dial clockwise Copying the recording area settings 8ADVANCED MENU SET Setting the ROI Page Setting ROI area 15 Set the areas in frame 2 and frame 3 in the same way 17 Press the [EXIT/OSD] button Confirming picture quality of ROI setting Page 3 Turn the jog dial to select “3.CAMERA CONTROL SET” and then turn the shuttle dial clockwise 7 Use the same procedure to set the connection channels of other dome cameras 15 Press the [EXIT/OSD] button 1 Press the [FUNC.] button (1) 2 Set the camera lens orientation 3 Press and hold the [PRESET] button (2) for about 3 seconds For example, CH02 corresponds to PRESET Operating the camera with the digital video recorder Page 7 Turn the jog dial to select “ON” and then turn the shuttle dial clockwise 8 Set “NTP SERVER ADDRESS” 10 Set “TIME TO SYNCHRONIZE” Example: 10:30 Page Page 1GETTING PREPARED Installing DVR Viewer2 Setting Internet Options 1 Select [Internet Options...] from the Internet Explorer [Tools] menu Example: Windows XP 2 Click the [Security] tab Minimum system requirements Audio playback requirements TCP/IP settings 1 Click the [Network and Internet Connections] icon in the [Control 2NETWORK CONTROL 4 Select a language and click [OK] 1 Click the button on the operation screen of the PC Display on the unit „When control rights are switched to the PC „When control rights are switched to the unit „Forced disconnection from the unit Display on the PC „When disconnected from the network „When network settings are changed Channel and screen selection buttons 1.Channel number 2.Channel selection (LV1/2/3/4) 3.Multi 9/16 screen display (LV1/2/3/4) 4.Quad-screendisplay (LV1/2/3/4) Click to display 4 screens 1 Click [CAMERA CONTROL] 2 Click each button to use a dome camera 2.Channel selection Select a camera channel 3.Pan/tilt 4.Menu set Finishing dome camera operation 3 Click [CAMERA CONTROL] 1RECORDING IMAGES 2WATCHING IMAGES Playback Click the button Adjusting the playback speed During playback, click the or button Reverse playback Page Page 1 Displays live image for users with download authorization „To cancel a save operation Click [CANCEL] 3SEARCHING FOR RECORDED VIDEO 1 Click “1. ALARM LOG SEARCH” on the “SEARCH” screen 2 Set a time period for “TERM” and click the [MOVE] button 3 Set the date and time 4 Set “SEARCH” to the desired search mode 5 Click the [SEARCH] button 1 Click “2. ALARM SEARCH” on the “SEARCH” screen 3 Click the preview screen to play back the image 1 Click “3. ALARM THUMBNAIL SEARCH” on the “SEARCH” screen 2 Click the thumbnail for the image to be played back 1 Click “4. TIME/DATE SEARCH” on the “SEARCH” screen 2 Specify the camera number from the “CHANNEL” pull-downmenu 4 Click [PREVIEW] 5 Click the preview screen to play back the image 1 Click “5. ARCHIVE AREA SEARCH” on the “SEARCH” screen 1 Click “6. MOTION DETECTION SEARCH” on the “SEARCH” screen 2 Specify the search area from the “SEARCH FROM” pull-downmenu SEARCH FROM CHANNEL (3) START/END 4SAVING (COPYING) RECORDED VIDEO Play a recorded image 6 Specify copy range as numeric values according to the “UNIT” settings 7 Specify “COPY CH” 8 Click the [START] button button on the operation 4 Set “UNIT” 5 Set “AUDIO” 6 Specify download range with numeric values depending on settings for “UNIT” 8 Set “DESTINATION FOLDER” 9 Click [START] 1SETTINGS Page 2INITIAL SET Setting the external clock 7 For “ADJUST TIME”, set the time at which the clocks are to be synchronized 8 Click [SAVE] 3 Click “3. HOLIDAY SET” 4 Specify the days to be treated as holidays 3RECORD SET AREA FULL RESET 4 Click [AREA FULL RESET] under “RECORDING AREA” Setting overwriting permission for recording areas 3 Click “2. RECORDING CONDITIONS SET” Setting the picture quality for recording 3 Click “3. NORMAL REC MODE SET” 4 Set “PICTURE QUALITY” Setting audio recording 5 Set “AUDIO RECORDING” to “ON” or “OFF” 7 Set “REC PROGRAM GROUP” to the desired program group 3 Click “4. PROGRAM REC SET” 4 Set “PROGRAM” to the desired program group 6 Click [SAVE] 3 Click “5. TIMER SET” 4 Set timer recording conditions for different days of the week (7) DLY (8) EXT „Performing timer recording Setting alarm recording 3 Click “6. ALARM REC MODE SET” 6 Set “AUDIO RECORDING” Audio recording is enabled when “REC RATE (Step 8)” is set to 1 FPS or more. ALL (P-1 – 4): Audio recording is enabled when “REC RATE” for any one of the program-registeredcameras is set to 1 FPS or more. ONLY (P-1 – 4): Setting pre-alarmrecording 10 Set “PRE-ALARMRECORDING” to “ON” or “OFF” 11 Set “REC RATE” to the desired recording rate 12 Set “DURATION” to the desired pre- alarm recording duration 13 Set “ALARM TRIGGER” to the desired 4GENERAL SET 3 Click “3. SECURITY LOCK SET” 3 Click “4. USER ID SET” 4 Set user ID for “USER ID” 5 Set “PASSWORD” 6 Set user level for “LV” 3 Click “5. RS-485SET” 3 Click “6. HDD SET” (1) Hard disk capacity (2) MIRRORING (3) PLAYBACK DRIVE 3 Click “7. NETWORK SET” 4 Change the settings as required 3 Click “8. NETWORK CONTROL SET” 6 Set “OPERATION AUTHORITY” to “NORMAL” or “CHANGE” 9 Click [SAVE] 5SCREEN SET 3 Click “2. MASK SET” 4 Set the following functions as required 6POWER LOSS/USED TIME 7INITIALIZATION LOG 8COPY MENU SETTINGS 9ADVANCED MENU SET 6 Set up “SMTP SERVER ADDRESS” and “PORT” 8 Specify “ON” or “OFF” for “USE” under “SEND MAIL ADDRESS” 9 Enter the recipient’s e-mailaddress under “MAIL ADDRESS” 10 Set “IMAGE” to “ON” or “OFF” 3 Click “2. CAMERA CONTROL SET” 4 Set “PROTOCOL” to the protocol corresponding to the dome camera 5 The address (000 to 127) is displayed in “ADD” 7 Use the same procedure to set the other channels 8 Set “2ND RS-485/422PROTOCOL” Set “NTP SERVER ADDRESS” 3 Click “4. TIME ZONE/NTP SET” 4 Set “TIME ZONE” 5 Set “SYNC. WITH NTP SERVER” to “ON” 1DVR VIEWER2 Initial screen 1Menu bar 1 File menu Open: Save: 1 Click in the toolbar 2 Click 3 Specify the folder in which the images are saved and click [OK] 4 Verify the displayed folder and click [OK] 5 Screen display Toolbar Full screen Quad screen 9 screen 16 screen (Viewer Operating Panel) 1 Playback slide bar 4 Audio adjusting section 2Operating buttons 3Playback speed adjusting section (Initial setting: 3) Full screen display Click in the toolbar or “Save” in the File menu Click in the toolbar or click “Print” in the File menu Click “Title Input” in the File menu 1Display format (‹ indicates default setting) To set the date display format 2INTERFACE SPECIFICATIONS The table below shows the commands supported by the digital video recorder 3Specifications Page „ Example: Recording to a 300 GB hard disk; internal HDD 300GB*1 (99%-usage) „ Example: Recording to a 500 GB hard disk; internal HDD 500GB*1 (99%-usage) Page Page Page Page Page 4MENU SETTING SEQUENCE Continued GENERAL SET (→P.111) SCREEN SET (→P.132) DISPLAY SET (→P.112) BUZZER SET (→P.114) INITIALIZATION LOG (→P.140) ADVANCED MENU SET (→P.144) ROI SET (→P.145) AREA SET (→P.147) ALARM NOTICE SET (→P.149) OpenSSL License Page INDEX Setting the interval and monitors for automatic screen User level 117, 131 Page Printed in Japan