SATO CX208/212 specification

SATO America, Inc.

545 Weddell Drive

Sunnyvale, CA 94089

Main Phone: (408) 745-1300

Tech Support Hot Line: (408) 745-1379

Fax: (408) 745-1309

http://www.satoamerica.com

©Copyright 2001 SATO America, Inc.

Warning: This equipment has been tested and found to comply with the limits for a Class B computing device pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed in accordance with the instruction may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and the receiver.

•Connect the equipment into an outlet or a circuit different from that to which the receiver is connected.

•Consult an experienced radio/TV technician for help.

Caution: The FCC warns the users that changes or modifications of the unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

All rights reserved. No part of this document may be reproduced or issued to third parties in any form whatsoever without the express permission of SATO America, Inc. The material in this document is provided for general information and is subject to change without notice. SATO America, Inc. assumes no responsibility for any errors that might appear.

Image 2

SATO CX208/212 manual

Contents

CX208/212 Page Table of Contents Sato CX208/212 Printers PN 9001092 Rev. a Introduction Sato Programming Language Using Basic Selecting Protocol Control Codes Printing with the Parallel Port Printing with the RS232 Port Print Area CX208/212 Programming GuidePage Rotated Fields Command Default Settings Printer Configuration Label Sensing ESCAESCCP1ESCCI2ESCCAESCZ Command Code page Reference Bar Codes MSI A01597 Input to Printer Printer Output CX208/212 Programming Guide Special Notes Printer Output Special Notes Command Structure ESCBWaabbbBar Codes, Expansion Command Structure ESCBTabbccddee Bar Codes, Variable Ratio This command must be immediately followed by the Escbw Command Structure ESCA3H-aaaaVbbbb Base Reference Point Printer configuration until a new Base Reference Point ESCK1H903F Command Structure Store Command ESCTabccCharacters, Custom-Designed Printer Input When printing the custom character using the Esck Recall Character Expansion This command will expand the following fonts Command Structure Escpr Character, Fixed Spacing Command Structure ESCPaa Character Pitch This command is affected by the Escl Character Expansion Command Structure Escps Character, Proportional Spacing Special Note Command StructureClear Print Jobs & Memory Command Structure None Continuous Forms Printing Example ESCWDH0100V0050X0600Y0400 Command Structure ESCWDHaaaaVbbbbXccccYddddCopy Image Area Horizontal 0001 Aaaa Cutter Command Command Structure ESC~aaaa or ESCNULaaaa Fonts U, S, M, OA, OB, XU, XS & XM Escoa Characters may be enlarged through the use of the Character Fonts WB, WL, XB & XL ESCWB1123456 Characters may be enlarged through the use of the Escl Form Feed Command Structure ESC Form Overlay, Recall Form Overlay, Store Command Structure ESCGabbbcccdata Graphics, Custom Custom graphic cannot be enlarged by the Escl Character Command Structure ESCGPaaaaa,data Graphics, PCX Command Structure Escj Journal Print ESCFWaabbVccccHdddd Command Structure Line ESCFWaabccccLines and Boxes CX208/212 Programming Guide Field ranges are Line Feed Command Structure ESCA1aaaabbbb Media Size Off-Line/Pause Command Structure ESCBPn...n Postnet Command Structure ESC#Ea Print Darkness Print Length, Expanded Maximum Print length, or until the printer is repowered Print Position ESCQ2ESCZAH0025100 0150ESCL0303ESCMSATO Print position of a field is affected by both the Rotate Command Structure ESCQaaaaaa Print Quantity Command Structure ESCCSa Print Speed Repeat Label Escc Command Structure ESC0 ESCzero Replace Data Partial Edit Fewer characters than the old data, then the characters not ESC100,50 Command Structure ESCaaaa,bbbbReverse Image CX208 CX212 Command Structure ESC%a Rotate, Fixed Base Reference Point Same data stream ESCAQ1ESCZNR Rotate, Moving Base Reference Point This command is provided for compatibility with other Sato ESCF001-001,04,03 Command Structure ESCFaaaabcccc,dd,eeSequential Numbering Value specified for Print Quantity should be equal to Start/Stop Label Expanded Memory Option Commands Command Structure ESC*a,bb Expanded Memory Function Clear Expanded Memory Example ESCBJT,11,02,02,01,00,0004,SATO Command Structure ESCBJT,aa,bb,cc,dd,ee,ffff,gg..gExpanded Memory Function Fonts, TrueType Recall Expanded Memory Function Fonts, TrueType Store Command Structure Command Function Printer Input ESCGRaaa Expanded Memory Function Graphics, Custom Recall Command Structure ESCGIabbbcccddddata Expanded Memory Function Graphics, Custom Store ESCGIHaaabbb002DATA Escz Command Structure ESCPYaaa Expanded Memory Function Graphics, PCX Recall Expanded Memory Function Graphics, PCX Store ESCPI001,32000,data ESCZCC2ESCA Expanded Memory Function Initialize ESCZACC1 Expanded Memory Function Area Select BJS Expanded Memory Function Status Two-Dimensional Symbols Two-Dimensional Bar Codes Maxicode Example ESCBV1,2,3,123456789,222,333,MESSAGEESC Please refer to UPS Publication Guide to Bar Coding with UPS BK0304400000021 Two-Dimensional Bar CodesCommand Structure Command Function Printer Input Values 00Hthru 1FHcan be specified as print data Configuration Commands Command Structure ESCCFa Auto-Calibrate Backfeed Enable Command Structure ESCCEa Calibrate Sensor Command Function Printer Input Printer Output Custom Protocol Command Codes DownloadCommand Structure ESCLD,a,b,c,d,e,f,g,h,i ESCLD,,,%,#,&,*,~,0,0 Resulting Command Code Command Structure ESCCBabb Label Tear-Off Print Darkness Range Adjustment Print Test Label ESC Azct Set Print Mode Command Structure ESCCPa Command Structure ESCCRaaaaa,b,c,d Set RS232 Parameters ESC AZCI2 Command Structure ESCCIaSet Sensor Type Enable Options ESC CL1 Mode