Auto-Calibrate, Command Structure ESCCFa | SATO CX208/212 specification

CX208/212 Programming Guide

Auto-Calibrate

Command Structure <ESC>CFa

a

=

0 Disable Auto-Calibrate

1Enable Auto-Calibrate

Example: <ESC>CF1

	Placement:	This command should be sent in a separate data
		stream.
	Default:	Enabled
Command Function	To enable/disable the Auto-Calibrate function.
Input to Printer	<ESC>AZCF1
Printer Output	Theres is no printer output as a result of this command.
Special Notes	1. When Auto-Calibrate is enabled, the printer will automatically

attempt to calibrate when it detects an out-of-paper condition (10" of platen feed after a label is printed without detecting a label edge or sense mark). If the calibration is successful, the printer shall move paper to the next index mark and resume normal operations. If the calibration is not successful, the printer shall indicate an out-of-paper condition by a red READY LED. The printer shall restore the original index circuit settings.

2. See “Label Sensing” on page 8 for more information on calibration.

Page 88

PN 9001092 Rev. A

SATO CX208/212 Printers

Image 92

SATO CX208/212 manual Auto-Calibrate, Command Structure ESCCFa

Contents

CX208/212 Page Table of Contents Sato CX208/212 Printers PN 9001092 Rev. a Introduction Sato Programming Language Using Basic Selecting Protocol Control Codes Printing with the Parallel Port Printing with the RS232 Port Print Area CX208/212 Programming GuidePage Rotated Fields Command Default Settings Printer Configuration Label Sensing ESCAESCCP1ESCCI2ESCCAESCZ Command Code page Reference Bar Codes MSI A01597 Input to Printer Printer Output CX208/212 Programming Guide Special Notes Printer Output Special Notes Command Structure ESCBWaabbbBar Codes, Expansion Command Structure ESCBTabbccddee Bar Codes, Variable Ratio This command must be immediately followed by the Escbw Command Structure ESCA3H-aaaaVbbbb Base Reference Point Printer configuration until a new Base Reference Point Command Structure Store Command ESCTabcc Characters, Custom-DesignedESCK1H903F Printer Input When printing the custom character using the Esck Recall Character Expansion This command will expand the following fonts Command Structure Escpr Character, Fixed Spacing Command Structure ESCPaa Character Pitch This command is affected by the Escl Character Expansion Command Structure Escps Character, Proportional Spacing Special Note Command StructureClear Print Jobs & Memory Command Structure None Continuous Forms Printing Example ESCWDH0100V0050X0600Y0400 Command Structure ESCWDHaaaaVbbbbXccccYddddCopy Image Area Horizontal 0001 Aaaa Cutter Command Command Structure ESC~aaaa or ESCNULaaaa Fonts U, S, M, OA, OB, XU, XS & XM Escoa Characters may be enlarged through the use of the Character Fonts WB, WL, XB & XL ESCWB1123456 Characters may be enlarged through the use of the Escl Form Feed Command Structure ESC Form Overlay, Recall Form Overlay, Store Command Structure ESCGabbbcccdata Graphics, Custom Custom graphic cannot be enlarged by the Escl Character Command Structure ESCGPaaaaa,data Graphics, PCX Command Structure Escj Journal Print ESCFWaabbVccccHdddd Command Structure Line ESCFWaabccccLines and Boxes CX208/212 Programming Guide Field ranges are Line Feed Command Structure ESCA1aaaabbbb Media Size Off-Line/Pause Command Structure ESCBPn...n Postnet Command Structure ESC#Ea Print Darkness Print Length, Expanded Maximum Print length, or until the printer is repowered Print Position ESCQ2ESCZAH0025100 0150ESCL0303ESCMSATO Print position of a field is affected by both the Rotate Command Structure ESCQaaaaaa Print Quantity Command Structure ESCCSa Print Speed Repeat Label Escc Command Structure ESC0 ESCzero Replace Data Partial Edit Fewer characters than the old data, then the characters not ESC100,50 Command Structure ESCaaaa,bbbbReverse Image CX208 CX212 Command Structure ESC%a Rotate, Fixed Base Reference Point Same data stream ESCAQ1ESCZNR Rotate, Moving Base Reference Point This command is provided for compatibility with other Sato ESCF001-001,04,03 Command Structure ESCFaaaabcccc,dd,eeSequential Numbering Value specified for Print Quantity should be equal to Start/Stop Label Expanded Memory Option Commands Command Structure ESC*a,bb Expanded Memory Function Clear Expanded Memory Example ESCBJT,11,02,02,01,00,0004,SATO Command Structure ESCBJT,aa,bb,cc,dd,ee,ffff,gg..gExpanded Memory Function Fonts, TrueType Recall Expanded Memory Function Fonts, TrueType Store Command Structure Command Function Printer Input ESCGRaaa Expanded Memory Function Graphics, Custom Recall Command Structure ESCGIabbbcccddddata Expanded Memory Function Graphics, Custom Store ESCGIHaaabbb002DATA Escz Command Structure ESCPYaaa Expanded Memory Function Graphics, PCX Recall Expanded Memory Function Graphics, PCX Store ESCPI001,32000,data ESCZCC2ESCA Expanded Memory Function Initialize ESCZACC1 Expanded Memory Function Area Select BJS Expanded Memory Function Status Two-Dimensional Symbols Two-Dimensional Bar Codes Maxicode Example ESCBV1,2,3,123456789,222,333,MESSAGEESC Please refer to UPS Publication Guide to Bar Coding with UPS BK0304400000021 Two-Dimensional Bar CodesCommand Structure Command Function Printer Input Values 00Hthru 1FHcan be specified as print data Configuration Commands Command Structure ESCCFa Auto-Calibrate Backfeed Enable Command Structure ESCCEa Calibrate Sensor Custom Protocol Command Codes Download Command Structure ESCLD,a,b,c,d,e,f,g,h,iCommand Function Printer Input Printer Output ESCLD,,,%,#,&,*,~,0,0 Resulting Command Code Command Structure ESCCBabb Label Tear-Off Print Darkness Range Adjustment Print Test Label ESC Azct Set Print Mode Command Structure ESCCPa Command Structure ESCCRaaaaa,b,c,d Set RS232 Parameters ESC AZCI2 Command Structure ESCCIaSet Sensor Type Enable Options ESC CL1 Mode