Print Darkness, Command Structure ESC#Ea | SATO CX208/212 manual

CX208/212 Programming Guide

Print Darkness

Command Structure <ESC>#Ea

	a	=	Print darkness value
			a = 1, 2, 3, 4 or 5
	Example:			<ESC>#E2
	Placement:			Must be placed immediately after <ESC>A and
	immediately before <ESC>Z in its own separate data stream
	Default:			2
Command Function	To specify a new print darkness setting. This command allows
	software control of the darkness setting for unique media and ribbon
	combinations.
Input to Printer	<ESC>AZ#E2
Printer Output	There is no printer output for this command.
Special Notes	1. This becomes the new setting in the printer configuration for all
		subsequent print jobs, unless changed. The setting is stored in
		non-volatile memory and is not affected by cycling power.

2. The lighest setting is the smallest value and the darkest setting is the largest value.

3. This command adjusts the print darkness in discrete steps. The range of this command is set using the <ESC>CD Print Darkness Fine Adjustment command. Changing the Print Darkness Fine Adjustment setting will affect this command.

Page 51

PN 9001092 Rev. A

SATO CX208/212 Printers

Image 55

SATO CX208/212 manual Print Darkness, Command Structure ESC#Ea

Contents

CX208/212 Page Table of Contents Sato CX208/212 Printers PN 9001092 Rev. a Sato Programming Language Introduction Selecting Protocol Control Codes Using Basic Printing with the RS232 Port Printing with the Parallel Port CX208/212 Programming Guide Print AreaPage Rotated Fields Printer Configuration Command Default Settings Label Sensing ESCAESCCP1ESCCI2ESCCAESCZ Command Code page Reference MSI Bar Codes Input to Printer A01597 Printer Output CX208/212 Programming Guide Special Notes Bar Codes, Expansion Command Structure ESCBWaabbbPrinter Output Special Notes Bar Codes, Variable Ratio Command Structure ESCBTabbccddee This command must be immediately followed by the Escbw Base Reference Point Command Structure ESCA3H-aaaaVbbbb Printer configuration until a new Base Reference Point Printer Input Command Structure Store Command ESCTabccCharacters, Custom-Designed ESCK1H903F When printing the custom character using the Esck Recall Character Expansion This command will expand the following fonts Character, Fixed Spacing Command Structure Escpr Character Pitch Command Structure ESCPaa This command is affected by the Escl Character Expansion Character, Proportional Spacing Command Structure Escps Clear Print Jobs & Memory Command StructureSpecial Note Continuous Forms Printing Command Structure None Copy Image Area Command Structure ESCWDHaaaaVbbbbXccccYddddExample ESCWDH0100V0050X0600Y0400 Horizontal 0001 Aaaa Command Structure ESC~aaaa or ESCNULaaaa Cutter Command Escoa Fonts U, S, M, OA, OB, XU, XS & XM Characters may be enlarged through the use of the Character ESCWB1123456 Fonts WB, WL, XB & XL Characters may be enlarged through the use of the Escl Form Feed Form Overlay, Recall Command Structure ESC Form Overlay, Store Graphics, Custom Command Structure ESCGabbbcccdata Custom graphic cannot be enlarged by the Escl Character Graphics, PCX Command Structure ESCGPaaaaa,data Journal Print Command Structure Escj Lines and Boxes Command Structure Line ESCFWaabccccESCFWaabbVccccHdddd CX208/212 Programming Guide Field ranges are Line Feed Media Size Command Structure ESCA1aaaabbbb Off-Line/Pause Postnet Command Structure ESCBPn...n Print Darkness Command Structure ESC#Ea Maximum Print Length, Expanded Print length, or until the printer is repowered ESCQ2ESCZAH0025100 0150ESCL0303ESCMSATO Print Position Print position of a field is affected by both the Rotate Print Quantity Command Structure ESCQaaaaaa Print Speed Command Structure ESCCSa Escc Repeat Label Replace Data Partial Edit Command Structure ESC0 ESCzero Fewer characters than the old data, then the characters not Reverse Image Command Structure ESCaaaa,bbbbESC100,50 CX208 CX212 Rotate, Fixed Base Reference Point Command Structure ESC%a Same data stream Rotate, Moving Base Reference Point ESCAQ1ESCZNR This command is provided for compatibility with other Sato Sequential Numbering Command Structure ESCFaaaabcccc,dd,eeESCF001-001,04,03 Value specified for Print Quantity should be equal to Start/Stop Label Expanded Memory Option Commands Expanded Memory Function Clear Expanded Memory Command Structure ESC*a,bb Expanded Memory Function Fonts, TrueType Recall Command Structure ESCBJT,aa,bb,cc,dd,ee,ffff,gg..gExample ESCBJT,11,02,02,01,00,0004,SATO Expanded Memory Function Fonts, TrueType Store Expanded Memory Function Graphics, Custom Recall Command Structure Command Function Printer Input ESCGRaaa Expanded Memory Function Graphics, Custom Store Command Structure ESCGIabbbcccddddata ESCGIHaaabbb002DATA Escz Expanded Memory Function Graphics, PCX Recall Command Structure ESCPYaaa ESCPI001,32000,data Expanded Memory Function Graphics, PCX Store Expanded Memory Function Initialize ESCZCC2ESCA Expanded Memory Function Area Select ESCZACC1 Expanded Memory Function Status BJS Two-Dimensional Symbols Example ESCBV1,2,3,123456789,222,333,MESSAGEESC Two-Dimensional Bar Codes Maxicode Please refer to UPS Publication Guide to Bar Coding with UPS Command Structure Command Function Printer Input Two-Dimensional Bar CodesBK0304400000021 Values 00Hthru 1FHcan be specified as print data Configuration Commands Auto-Calibrate Command Structure ESCCFa Command Structure ESCCEa Backfeed Enable Calibrate Sensor ESCLD,,,%,#,&,*,~,0,0 Custom Protocol Command Codes DownloadCommand Structure ESCLD,a,b,c,d,e,f,g,h,i Command Function Printer Input Printer Output Resulting Command Code Label Tear-Off Command Structure ESCCBabb Print Darkness Range Adjustment ESC Azct Print Test Label Command Structure ESCCPa Set Print Mode Set RS232 Parameters Command Structure ESCCRaaaaa,b,c,d Set Sensor Type Command Structure ESCCIaESC AZCI2 ESC CL1 Enable Options Mode