Calibrate Sensor, Command Structure | SATO CX208/212 guide

CX208/212 Programming Guide

Calibrate Sensor

Command Structure	<ESC>CA
	Example:	<ESC>CA
	Placement:	This command should be sent after the sensor type
		has been selected with the <ESC>CI command. It
	should
		not be included with print job commands.
	Default:	There is no default for this command.
Command Function	To adjust the label sensor for unique media and ribbon combinations.
Input to Printer	<ESC>AI2CZA

Printer Output	There is no printer output for this command. It will cause the printer to
	feed a label while the characteristics of the label backing or eye-mark
	are measured.
Special Notes	1.	The sensor is calibrated for the currently selected sensor type
		(Eye-Mark or Transmissive).
	2.	If the Sensor is disabled with a <ESC>CI0 command, no
		calibration is performed.
	3.	The sensor must be recalibrated whenever the sensor type is
		changed.
	4.	When calibrating the sensor for the CX200/212TT Thermal
		Transfer unit operating in the thermal transfer mode, the ribbon
		must be installed in the printer.

Page 90

PN 9001092 Rev. A

SATO CX208/212 Printers

Image 94

SATO CX208/212 manual Calibrate Sensor, Command Structure

Contents

CX208/212 Page Table of Contents Sato CX208/212 Printers PN 9001092 Rev. a Introduction Sato Programming Language Using Basic Selecting Protocol Control Codes Printing with the Parallel Port Printing with the RS232 Port Print Area CX208/212 Programming GuidePage Rotated Fields Command Default Settings Printer Configuration Label Sensing ESCAESCCP1ESCCI2ESCCAESCZ Command Code page Reference Bar Codes MSI A01597 Input to Printer Printer Output CX208/212 Programming Guide Special Notes Bar Codes, Expansion Command Structure ESCBWaabbbPrinter Output Special Notes Command Structure ESCBTabbccddee Bar Codes, Variable Ratio This command must be immediately followed by the Escbw Command Structure ESCA3H-aaaaVbbbb Base Reference Point Printer configuration until a new Base Reference Point ESCK1H903F Command Structure Store Command ESCTabccCharacters, Custom-Designed Printer Input When printing the custom character using the Esck Recall Character Expansion This command will expand the following fonts Command Structure Escpr Character, Fixed Spacing Command Structure ESCPaa Character Pitch This command is affected by the Escl Character Expansion Command Structure Escps Character, Proportional Spacing Clear Print Jobs & Memory Command StructureSpecial Note Command Structure None Continuous Forms Printing Copy Image Area Command Structure ESCWDHaaaaVbbbbXccccYddddExample ESCWDH0100V0050X0600Y0400 Horizontal 0001 Aaaa Cutter Command Command Structure ESC~aaaa or ESCNULaaaa Fonts U, S, M, OA, OB, XU, XS & XM Escoa Characters may be enlarged through the use of the Character Fonts WB, WL, XB & XL ESCWB1123456 Characters may be enlarged through the use of the Escl Form Feed Command Structure ESC Form Overlay, Recall Form Overlay, Store Command Structure ESCGabbbcccdata Graphics, Custom Custom graphic cannot be enlarged by the Escl Character Command Structure ESCGPaaaaa,data Graphics, PCX Command Structure Escj Journal Print Lines and Boxes Command Structure Line ESCFWaabccccESCFWaabbVccccHdddd CX208/212 Programming Guide Field ranges are Line Feed Command Structure ESCA1aaaabbbb Media Size Off-Line/Pause Command Structure ESCBPn...n Postnet Command Structure ESC#Ea Print Darkness Print Length, Expanded Maximum Print length, or until the printer is repowered Print Position ESCQ2ESCZAH0025100 0150ESCL0303ESCMSATO Print position of a field is affected by both the Rotate Command Structure ESCQaaaaaa Print Quantity Command Structure ESCCSa Print Speed Repeat Label Escc Command Structure ESC0 ESCzero Replace Data Partial Edit Fewer characters than the old data, then the characters not Reverse Image Command Structure ESCaaaa,bbbbESC100,50 CX208 CX212 Command Structure ESC%a Rotate, Fixed Base Reference Point Same data stream ESCAQ1ESCZNR Rotate, Moving Base Reference Point This command is provided for compatibility with other Sato Sequential Numbering Command Structure ESCFaaaabcccc,dd,eeESCF001-001,04,03 Value specified for Print Quantity should be equal to Start/Stop Label Expanded Memory Option Commands Command Structure ESC*a,bb Expanded Memory Function Clear Expanded Memory Expanded Memory Function Fonts, TrueType Recall Command Structure ESCBJT,aa,bb,cc,dd,ee,ffff,gg..gExample ESCBJT,11,02,02,01,00,0004,SATO Expanded Memory Function Fonts, TrueType Store Command Structure Command Function Printer Input ESCGRaaa Expanded Memory Function Graphics, Custom Recall Command Structure ESCGIabbbcccddddata Expanded Memory Function Graphics, Custom Store ESCGIHaaabbb002DATA Escz Command Structure ESCPYaaa Expanded Memory Function Graphics, PCX Recall Expanded Memory Function Graphics, PCX Store ESCPI001,32000,data ESCZCC2ESCA Expanded Memory Function Initialize ESCZACC1 Expanded Memory Function Area Select BJS Expanded Memory Function Status Two-Dimensional Symbols Two-Dimensional Bar Codes Maxicode Example ESCBV1,2,3,123456789,222,333,MESSAGEESC Please refer to UPS Publication Guide to Bar Coding with UPS Command Structure Command Function Printer Input Two-Dimensional Bar CodesBK0304400000021 Values 00Hthru 1FHcan be specified as print data Configuration Commands Command Structure ESCCFa Auto-Calibrate Backfeed Enable Command Structure ESCCEa Calibrate Sensor Command Function Printer Input Printer Output Custom Protocol Command Codes DownloadCommand Structure ESCLD,a,b,c,d,e,f,g,h,i ESCLD,,,%,#,&,*,~,0,0 Resulting Command Code Command Structure ESCCBabb Label Tear-Off Print Darkness Range Adjustment Print Test Label ESC Azct Set Print Mode Command Structure ESCCPa Command Structure ESCCRaaaaa,b,c,d Set RS232 Parameters Set Sensor Type Command Structure ESCCIaESC AZCI2 Enable Options ESC CL1 Mode