Configuration | Schneider Electric Altivar 212 guide

Configuration

Configuration

3

What's in this Chapter?

This chapter contains the following topics:

Topic

Configuration of the communication parameters

Configuration of the control source

Configuration of the indirect blocks

Configuration of the communication interruption

Page

20

21

27

28

The settings of communication-related parameters can be changed from the operation panel or from Modbus (PLC, computer or controller) or from graphic display option.

Note that there are two types of parameters: parameters whose settings take effect immediately after the setting and parameters whose settings do not take effect until the drive is turned back on or reset. In the table below, these 2 types are mentioned in the column "valid" by "After setting" and "After power cycle".

S1A53844 01/2011

19

Image 19

Schneider Electric Altivar 212 manual Configuration, Whats in this Chapter?

Contents

Altivar S1A53844 01/2011 Table of Contents Table of Contents Important Information Safety Information At a Glance About the Book Hazard of Electric SHOCK, Explosion or ARC Flash S1A53844 01/2011 Introduction Introduction Whats in this Chapter? Hardware setupTopic Tightening torque Pin out of the Open Style Modbus connectorRJ45 Cross section Open Style Reference Connection via Open Style wiring systemPin out of the RJ45 Modbus connector Pin Signal RJ45 Reference Connection via RJ45 wiring systemConnection accessories Connecting cables Protection Against Interference PTC resistor value F646 Description of terminals GND Hardware setup Configuration After Configuration of the communication parametersAccess to the parameters Parameters Modbus Adjustment range Default Valid Address Communication Configuration of the control sourceParameters Modbus Setting Control by the Modbus network Control by the terminals, monitoring by the Modbus network Setting Default ValidParameters Parameters Modbus Setting Default Valid LI R selection Parameters Modbus Setting Default Valid AddressCom channel choice F807 Communication Menu COM submenu LI R selection F112 VIA VIA Parameters LocationRemote spd ref 2 F207 Frequency source Commands CMOd Complete control diagram Configuration Configuration of the indirect blocks Configuration of the communication interruption 2129 Configure the drive behaviourParameter Modbus Setting Default Valid Address Communication detected fault 16#851 Configuration Modbus services Slave address Function code Data RTU modePrinciple of the Modbus protocol Slave Slave j Slave k Read one word Modbus functions availableFunction 3, quantity = Function 3, quantity = 1 Read indirect blockStatus info Read indirect block of 2 parameters Write Single Register Function 16 = 16#10, quantity =1 Write multiple registers Write indirect block Command word Frequency SetpointSpeed Setpoint Request 6C 7E Response Read Device Identification 43/14 Exception code Error response Modbus services Parameter list General Auto ramp AUI Disabled ManualSetting of Max frequency FH Referring to the Altivar 212 programming manual Outputs control from serial communication Commands from serial communicationList of control parameters Setpoints from serial communication Current and torque List of monitoring parametersStatus Frequency and speed Values Power and energyMaintenance Trip and alarm codes Command word FA00 CommandsBit Specifications Remarks Over-current stall level change bit Command word 2 FA20Energy reset bit Examples Frequency setpoint FA01 SetpointsSpeed setpoint FA13 Status word FE0I Fd01 Status Status word 3 FE49 Fd49 Command mode status FE45Setpoint mode status FE46 Status word 2 FE42 Fd42 Alarm code FC91 Trip and alarm codesAlarm of run time FE79 Code Value Description Hexadecimal number Decimal number Bit Terminal name Function parameter title Monitoring and control of I/O from communicationDigital inputs status Fd06, FE06 Digital outputs status Fd07, FE07 Analog inputs values FE35, FE36 Digital outputs command FA50Analog outputs command FA51 Damper opening command F580 = 3 Identification Model Voltage Power Rating Code FB05 Class FB72bit8Drive model code F805 ATV212WU15N4C S1A53844 01/2011 Appendix Schematic diagram Modbus 2-wire standard schematicRS485 standard Migration For example Migration ATV21 ATV212Commissioning ATV212Modbus manualENS1A5384401 S1A53844 01/2011