Power and energy, Maintenance | Schneider Electric Altivar 212

Parameter list

Power and energy

	Parameter	Modbus		Unit	Description
		address

	Input power (FE29)	65065	16#FE29	kW	Value before trip

	Output power (FE30)	65072	16#FE30	kW	Value before trip

	Input energy (FE76)	65142	16#FE76	kWh	-

	Output energys (FE77)	65143	16#FE77	kWh	-

Maintenance

	Parameter	Modbus		Unit	Description
		address

	Motor load (FE26)	65062	16#FE26	%	Value before trip

	Inverter load (FE27)	65063	16#FE27	%	Value before trip

	Cumulative run time (FE14)	65044	16#FE14	h	-

	Cumulative power on time (FE80)	65152	16#FE80	h	-

I/O values

	Parameter	Modbus		Description
		address

	Digital inputs status Fd06	64774	16#Fd06	Current value

	Digital outputs status Fd07	64775	16#Fd07	Current value

	Digital inputs status at last trip FE06	65030	16#FE06	Value before trip

	Digital outputs status at last trip FE07	65030	16#FE07	Value before trip

	Analog input VIA value FE35	65077	16#FE35	-

	Analog input VIB value FE36	65078	16#FE36	-

Trip and alarm codes

Parameter

Modbus address

Description

Trip code FC90	64656 16#FC90	-

Alarm code FC91	64657 16#FC91	-

Alarm of run FE79	65145 16#FE79	-

Latest trip code FE10	65040 16#FE10	-

2nd previous trip code FE11	65041 16#FE11	-

3rd previous trip code FE12	65042 16#FE12	-

4th previous trip code FE13	65043 16#FE13	-

S1A53844 01/2011

47

Image 47

Schneider Electric Altivar 212 manual Power and energy, Maintenance, Values, Trip and alarm codes

Contents

Altivar S1A53844 01/2011 Table of Contents Table of Contents Important Information Safety Information At a Glance About the Book Hazard of Electric SHOCK, Explosion or ARC Flash S1A53844 01/2011 Introduction Introduction Topic Hardware setupWhats in this Chapter? Tightening torque Pin out of the Open Style Modbus connectorRJ45 Cross section Open Style Reference Connection via Open Style wiring systemPin out of the RJ45 Modbus connector Pin Signal RJ45 Reference Connection via RJ45 wiring systemConnection accessories Connecting cables Protection Against Interference PTC resistor value F646 Description of terminals GND Hardware setup Configuration After Configuration of the communication parametersAccess to the parameters Parameters Modbus Adjustment range Default Valid Address Communication Configuration of the control sourceParameters Modbus Setting Control by the Modbus network Parameters Setting Default ValidControl by the terminals, monitoring by the Modbus network Parameters Modbus Setting Default Valid LI R selection Parameters Modbus Setting Default Valid AddressCom channel choice F807 Communication Menu COM submenu LI R selection F112 VIA VIA Parameters LocationRemote spd ref 2 F207 Frequency source Commands CMOd Complete control diagram Configuration Configuration of the indirect blocks Configuration of the communication interruption 2129 Configure the drive behaviourParameter Modbus Setting Default Valid Address Communication detected fault 16#851 Configuration Modbus services Slave address Function code Data RTU modePrinciple of the Modbus protocol Slave Slave j Slave k Function 3, quantity = Modbus functions availableRead one word Status info Read indirect blockFunction 3, quantity = 1 Read indirect block of 2 parameters Write Single Register Function 16 = 16#10, quantity =1 Write multiple registers Speed Setpoint Command word Frequency SetpointWrite indirect block Request 6C 7E Response Read Device Identification 43/14 Exception code Error response Modbus services Parameter list General Auto ramp AUI Disabled ManualSetting of Max frequency FH Referring to the Altivar 212 programming manual Outputs control from serial communication Commands from serial communicationList of control parameters Setpoints from serial communication Current and torque List of monitoring parametersStatus Frequency and speed Values Power and energyMaintenance Trip and alarm codes Bit Specifications Remarks CommandsCommand word FA00 Over-current stall level change bit Command word 2 FA20Energy reset bit Examples Speed setpoint FA13 SetpointsFrequency setpoint FA01 Status word FE0I Fd01 Status Status word 3 FE49 Fd49 Command mode status FE45Setpoint mode status FE46 Status word 2 FE42 Fd42 Alarm of run time FE79 Trip and alarm codesAlarm code FC91 Code Value Description Hexadecimal number Decimal number Bit Terminal name Function parameter title Monitoring and control of I/O from communicationDigital inputs status Fd06, FE06 Digital outputs status Fd07, FE07 Analog inputs values FE35, FE36 Digital outputs command FA50Analog outputs command FA51 Damper opening command F580 = 3 Drive model code F805 Model Voltage Power Rating Code FB05 Class FB72bit8Identification ATV212WU15N4C S1A53844 01/2011 Appendix RS485 standard Modbus 2-wire standard schematicSchematic diagram Migration Commissioning Migration ATV21 ATV212For example ATV212Modbus manualENS1A5384401 S1A53844 01/2011